Sort By
Per Page
View
Grid
List
Kirjes Bowl Sander - 40 x 40mm Sleeve
This Kirjes Ball Drum Sander is 40 x 40mm.
Sold individually - discounts available for bulk (see pricing above).
Every sanding sleeve is made to specifically fit each inflatable sander. On the round sander, the overlapping design of the sanding sleeves is to ensure longevity and optimum effectiveness in awkward places.
Vallorbe Triangular Saw Files
To choose the right file, size it to the tooth. Ideally, about half of the cutting surface of the file will be in contact with the tooth -- half of the file will be in the gullet and the other half unused. When you rotate the file to get a fresh edge, it will be uniformly sharp. If you use a smaller file, only some of the new surface will be fresh and the rest dull.
Lie-Nielsen A2 Bevel Edge Chisels
Lie-Nielsen A2 bevel edge chisels - these will hold their edge longer than high carbon chisels and therefore require less frequent sharpening.
The chisel edges are square, parallel along the length, and very narrow so you can get into tight places. The backs are ground flat and finished by hand at 400 grit. The bevel is flat ground at 30°, but a higher secondary bevel (about 35°) is advisable,...
Ashley Iles MKII Bench Chisels
These Ashley Iles MKII bench chisels are so attractively priced - how do they do it? These MKII chisels are a great improvement upon the original MKI's.
Hardened O1 high carbon steel with slim tapered blades which gives you access to tight spaces. The backs are also ever so slightly concave (a few thousands of an inch!) This is designed to help with sharpening.
Padauk handles with brass ferules.
Set...
Japanese Waterstones - Toishi-Ohishi
Toishi-Ohishi offer 7 single grit stones and 6 combination stones.
These stones are 8" (205mm) long, 3 inches (75mm) wide and a minimum of 1" (25mm) thick*.
The 3" (75mm) width makes them particularly useful when honing wide plane blades, knives or cut throat razors.
*Stone sizes:
220 grit - 205 x 80 x 35mm
All other single grit stones 205 x 75 x 25mm
Combination stones...
Kirjes Small Bowl Sander - 20 x 20mm Sleeve
These sleeves are for the Kirjes Small Bowl Sander (20 x 20mm).
Sold individually - discounts available for bulk (see pricing above).
Every sanding sleeve is made to specifically fit each inflatable sander. On the round sander, the overlapping design of the sanding sleeves is to ensure longevity and optimum effectiveness in awkward places.
DMT Diamond 8'' Dia-Sharp Bench Stones
The surface of this plate has continuous diamond abrasive bonded to it (not polka dot pattern)
The 8" version of this bench stone is the most popular Dia-Sharp® size. It's large enough to handle almost any tool or knife and is offered by us in 7 grits. Guaranteed not to hollow or groove, DMT®'s precisely engineered Dia-Sharp® Bench Stone with continuous diamond surface assures consistent, even...
Pfeil Lino & Block Cutting Tools - Individual
Pfeil palm handled tools for lino and block cutting available in wide range of sizes. These tools are the same high quality as the basic carving tools.
Precisely ground and polished.
Pear handles, 70mm blade length, 125mm overall length
Please see the larger images for the shape of the tool.
Veritas Mk.II Honing Guide
The key to consistent and fast honing is repeatability - and this guide delivers it in spades. Whether you're a sharpening veteran or just starting out, this versatile guide lets you concentrate on sharpening without worrying about controlling blade angle at the same time. This makes your honing reliable, accurate and consistent. Three options let you choose the honing guide that best suits your...
Abranet Strips - Pack of 10
Abranet strips are aluminium oxide resin bonded polyamide fabric strips. We offer a choice of the most popular grits from 80grit (coarse) through to 600grit (super fine) and they are available in packs of 10 or 50.
Strips measure 70mm by 125mm
Please choose your grit and quantity carefully.
MoraKniv 120 Sloyd Woodcarving Knife
The Mora 120 Sloyd woodcarving knife is the shorter of the two we carry. The thin (2.8mm thick by 60mm long) blade is made from carbon steel which is easier to sharpen, and will ultimately give you a better edge over the laminated blades. Comes sharp, ready to go to work. The handle is made from oiled birch which is barrell shaped to give good grip. The tang runs the full length of the handle which...
Narex Richter Bevel Edge Chisels
Until recently we stocked the Narex 8116 range of bevel edge chisels which were popular amongst students and people starting out in woodworking. Most importantly the steel in the 8116 range was very good but in our opinion the balance and feel would sometimes let them down. I'm glad to say that this new premium range 8150 from Narex is a massive improvement upon the old chisels. Yes they are not...
Pfeil Straight Gouge - Series 9
Straight Gouges are used for shaping recesses and raised surfaces, for instance folds such as drapery. Our broad range of sweeps and widths opens unlimited possibilities in sculpture carving.
Pfeil Straight Gouge - Series 8
Straight Gouges are used for shaping recesses and raised surfaces, for instance folds such as drapery. The broad range of sweeps and widths offered by Pfeil opens unlimited possibilities in sculpture carving.
Series 7 and 8 sweeps are particularly useful for finishing work.
Paul Adamson recommends the 25mm tool for making a Kuksa, his book can be viewed here
Pfeil Straight Gouge - Series 5
Straight Gouges are used for shaping recesses and raised surfaces, for instance folds such as drapery. Our broad range of sweeps and widths opens unlimited possibilities in sculpture carving.
Kirjes Long Cylindrical Sander - 28 x 80mm Sleeve
These sleeves are for the Kirjes Long Cylindrical Sander (28 x 80mm).
Sold individually - discounts available for bulk (see pricing above).
The sanding cloth material is highly flexible and made of the very best quality, sanding not only wood but also metals, plastic, bone and horn.
The sharpness of the abrasive lasts a long time, however, we highly recommend using a cleaning stick to considerably...
Shapton Ceramic Glass Stone
The Shapton stones are ceramic which means they will wear more slowly than a traditional waterstone, but still cut quickly to get you back working in no time.
The ceramic grit is bonded to float glass which also helps maintain the stones flatness.
No need to soak, just splash water on to its surface, and you are ready to go.
Like a waterstone these Shapton Glass Stones will need to be flattened...
Shapton Kuromaku Professional Series Stones
These are the ever popular Shapton Kuromaku Stones. They also known as Shapton Professional or Shapon Pro whetstones, but are all one and the same thing. They are ceramic which means they will wear more slowly than a traditional waterstone, but still cut quickly to get you back working in no time. Ideal for sharpening woodworking blades and chisels, aswell as kitchen knives and straight razors.
No...
Lie-Nielsen No.60 1/2 Block Plane
The Lie-Nielsen No 60½ Block Plane is based upon the old Stanley No 60½.
This is a superb little block plane and should be in your tool kit, useful for all woodworking jobs in particular great for trimming end grain. The movable shoe in front of the blade allows you to easily adjust the mouth opening - fine mouth for finishing your work and wafer thin shavings or the wider opening...
Kirjes Short & Fat Cylindrical Sander - 42 x 44mm Sleeve
These sleeves are for the Kirjes short & fat Cylindrical Sander (42 x 44mm).
Sold individually - discounts available for bulk (see pricing above).
The sanding cloth material is highly flexible and made of the very best quality, sanding not only wood but also metals, plastic, bone and horn.
The sharpness of the abrasive lasts a long time, however, we highly recommend using a cleaning stick...
Veritas Side-Clamping Honing Guide
The tried-and-true design of a side-clamping guide is familiar to most woodworkers. This side-clamping honing guide is a piece of modern-day engineering that improves on this established design while maintaining the flexibility of this type of guide. Chisels and plane blades ranging from 1/8" (3mm) to 2½" (63mm) fit securely for accurate honing. The unique three-point holding position...
Hock Bench Plane Blades
Ron Hock has earned an international reputation for the quality of his plane blades. Ron incorporates the same basic principles as used by 19th Century edge tools makers in his high carbon steel blades and updates these principles in his A2 cryogenically treated steel.
High carbon steel blades are easier to sharpen and will give you a fantastic cuting edge. However they will require more frequent...
Pfeil Straight Gouge - Series 7
Straight Gouges are used for shaping recesses and raised surfaces, for instance folds such as drapery. Our broad range of sweeps and widths opens unlimited possibilities in sculpture carving.
Series 7 and 8 sweeps are particularly useful for finishing work.
Pegas Skip Tooth Blades
These Pegas scroll saw blades are a good all round versatile application blade. The range of sizes and teeth per inch allows the cutting of intricate patterns as well as rough-cut work. Thickness of work range from 1/16 inch to 2½ inch. Skip scroll saw blades perform well with wood, plastic, bone, Corian and most fibrous materials. The blades provide good chip removal, will accept a fast feed...
Sharpen This
by Christopher Schwarz
Sharpening is not a sport.
If you want to be a better woodworker, you need to learn to sharpen. If you want to be a better sharpener, you need to stop paying so much attention to tertiary bevels and carbide formations in steel and start paying attention to the wood. If the wood is cut cleanly, then your tools are sufficiently sharp. If the wood is torn out and covered in...
Pfeil Straight Gouge - Series 3
Straight Gouges are used for shaping recesses and raised surfaces, for instance folds such as drapery. Our broad range of sweeps and widths opens unlimited possibilities in sculpture carving.
Pfeil Series 1 - Double Bevel Chisel
These are straight chisels with a double bevel. Straight chisels are used to carve the blank into rough form and to work on large areas.
Veritas Narrow Router Plane Blades
These high-carbon steel router plane blades fit the Veritas large and merdium router planes, as well as Stanley #71 router planes (with the height-adjustment nut inverted). The narrow single-piece blades are available in both metric and imperial sizes.
Please note that Veritas do not produce a 3mm and a 1/8" blade, they consider them close enough in size so we only advertise the 1/8".
Sizes...
Brusso Brass Shelf Sleeves K-2
The K-2 brass heavy-walled shelf support sleeve is mortised flush into the side of a case, providing an anchor for the K-10 shelf support pin. The sleeve measures 3/8" in diameter x 7/16" deep. Supplied as a set of 12.
Pfeil Series 12 - 60° V Parting Tools
For carving lettering and ornamentation and for sculpting figures.
60°
Veritas Pocket Layout Square - Metric
Just as a speed square is an essential layout tool for carpenters and framers, these small squares are similar in both form and function but are appropriately sized for laying out joinery and other common workshop tasks.
Available individually and as a set including 35mm, 60mm and 85mm squares – each a compact, lightweight tool that fits into a pocket, comes to hand nicely, and is easy to...
Wood is Good Unbreakable Mallets
Wood is Good wood carving mallets from the USA.
These mallets are made with an American maple handle and a urethane head that is guaranteed to be unbreakable. They are designed to be quiet and yet able to transmit the maximum force to the tool.
The smaller sizes seem to be the most popular (with the 18oz the biggest seller) but the biggies also appeal to those of you doing larger scale work or...
Lie-Nielsen Honing Guide
The Lie-Nielsen version of the side clamping style of honing guide is solidly machined from Stainless Steel, with a Bronze bearing.
Their Honing Guide features removable jaws: it comes with a standard pair of jaws that fit most Lie-Nielsen blades, and additional jaws are available (sold separately) for Chisels 3/16" and under, tall jaws for Mortice Chisels, long jaws for very short blades and...
Lie-Nielsen Bronze Low Angle Block Plane
The Lie-Nielsen small bronze Low Angle Block Planes fit perfectly in the hand and slip easily into the pocket. The 5¼" body holds a 1¼" x 1/8" thick blade. An unobtrusive Stainless Steel adjuster offers blade control of micrometer ease and precision with minimum backlash. The mouth is not adjustable.
The blade in the Low Angle Plane is bedded at 12° for fine cuts...
MoraKniv 106 Sloyd Woodcarving Knife
The Mora 106 Sloyd woodcarving knife has a slightly longer blade than the 120 for larger cuts. The thin (2.8mm thick by 82mm long) blade is made from carbon steel which is easier to sharpen, and will ultimately give you a better edge over the laminated blades. Comes sharp, ready to go to work. The handle is made from oiled birch which is barrell shaped to give good grip. The tang runs the full length...
Pfeil Straight Gouge - Series 11
Straight Gouges are used for shaping recesses and raised surfaces, for instance folds such as drapery. Our broad range of sweeps and widths opens unlimited possibilities in sculpture carving.
Series 11 are the narrowest and are ideal for carving fine details like hair.
The Anarchist's Tool Chest
By Christopher Schwarz
"When I am too exhausted, ill or busy to work in my shop, I will shuffle down the stairs to my 15' x 25' workshop and simply stand there for a few minutes with my hands on my tools.
To be sure, I thought I was a touch nuts because of this personality quirk. But after reading the oral histories and diaries of craftsmen from the last 300 years, I found it's...
Pfeil Straight Gouge - Series 2
Straight Gouges are used for shaping recesses and raised surfaces, for instance folds such as drapery. Our broad range of sweeps and widths opens unlimited possibilities in sculpture carving.
Kirjes Short Cylindrical Sander - 20 x 32mm Sleeve
These sleeves are for the Kirjes Short Cylindrical Sander (20 x 32mm).
Sold individually - discounts available for bulk (see pricing above).
The sanding cloth material is highly flexible and made of the very best quality, sanding not only wood but also metals, plastic, bone and horn.
The sharpness of the abrasive lasts a long time, however, we highly recommend using a cleaning stick to considerably...
Ray Iles Rounding Planes
A rounder is also known as rotary plane and is used to create accurate tenons or for rounding spindles for chairs. All of these 6 rounders are made by Ray Iles.
The thick blade is held in place by two washered screws which allows you to adjust or remove the blade for sharpening very easily.
Beech body, lightly linseed oiled.
Having reduced your spindle to a little over the size of the rounder...
Connells Leather Strop & Paste
A strop is a leather strip used to polish the edge of a chisel, plane iron or a knife. Stropping is the final part of the sharpening process in achieving a truly sharp edge. Stropping has always been the accepted way to finishing a cut throat razor guaranteeing the closet of shaves. Unlike honing which removes metal from the bevel, stropping burnishes away any microscopic metal strands clinging to...
Ashley Iles MKII Butt Chisels
Butt or American Pattern Bevel Edge Chisels are a shorter version of the standard length. Used where the chisel is pushed rather than struck with a mallet, the shorter handle fitting snugly into the palm of the hand.
Hardened O1 Carbon Steel. Padauk handles.
Set of 5 includes 1/4" (6mm), 3/8" (9mm), 1/2" (12mm), 3/4" (19mm) and 1" (25mm).
Veritas Plane Screwdriver
A regular screwdriver just doesn't work well on cap iron screws. A narrow blade can mar the cap-screw slot, and there's always the risk that the screwdriver tip will slip out of the slot altogether. Veritas have designed this screwdriver to make it both safe and easy to remove, replace or adjust cap irons.
It has a turned brass collar surrounding the tip to capture the head of a cap iron screw...
Pfeil Carpenter Chisels
Introduced in 2010 from Switzerland, Pfeil Carpenters Chisels have strong Elm wood octagonal handles with an oval section. We prefer these to the bench chisels.
The blades are forged from K 510 steel, hardened up to 60 RC. Bevel edged with well marked facets. The blades are finely ground and polished.
Bevel angle 25°, razor sharp.
4mm wide to 40mm wide.
Overall length 240-260mm.
Narex Marking Knives
The Narex marking knife is an essential tool for creating marks on wood when laying out precision joinery or transferring measurements. The flat handle profile prevents the knife from rolling off the bench.
With the addition of laser cut finger indents which are useful for applying pressure closer to the tip.
Available in three thicknesses; 2.5mm, 1.2mm, & 0.75mm
Handle: Polished Rosewood...
The Anarchist's Design Book: Expanded Edition
Why is this book on sale? Basically Lost Art Press need some storage space as the floors are creaking in their new Anthe Building. Please visit the Lost Art Press Blog for more information.
By Christopher Schwarz
Most of the American furniture we celebrate as the pinnacle of design is overbearing, over-embellished and a monument to waste and excess.
These high styles of furniture took hold...
Veritas Micro Adjust Marking Gauge
The Veritas wheel marking gauge is a great workhorse and excellent value. Its popularity led to the development of a second model that incorporates a micro-adjust feature. It is similar to our standard wheel marking gauge with an anodized aluminium body, brass face, stainless-steel rod and internal O-ring to keep a constant light friction force on the rod. It differs in that the body is slightly...
Lie-Nielsen No.507 Rebating Block Plane
The Lie-Nielsen No 507 Rebating Block Plane is also described as a Lie-Nielsen 60½ Rebating Block Plane (60 1/2R).
This 12° angle rebate block plane is based on an old Sargent block plane (No 507). The plane body is made from unbreakable ductile iron and is ground flat and square to .001". The cap iron is polished bronze. The throat is non adjustable. It is 6¼" long...