Sort By
Per Page
View
Grid
List
Workshop Wound Care
by Dr. Jeffery Hill
“Workshop Wound Care” – part of the Lost Art Press pocket book series – delves right to the heart of what you need to know when faced with common workshop injuries, from lacerations, to puncture wounds to material in the eye.
The author, Dr. Jeffery Hill, is an emergency room physician and an active woodworker. So he knows exactly the information a...
Mouldings in Practice
By Matthew Sheldon Bickford
Words from Chris Schwarz of Lost Art Press
After years of publishing woodworking information, you often hear that there is nothing new in the craft. Everything has been done before, written before and fully figured out.
I used to believe that was true, until I read the manuscript that was to become “Mouldings in Practice” by Matthew Sheldon Bickford....
Pfeil Chip Carving Knife - Kerb 1
Pfeil Chip Carving Knives come in a variety of shapes, this one is a Kerb 1 also known as Rosenmesser.
A simple knife for chip carving with a straight blade. You can use it to carve patterns (geometric or simple flowers) as well as whittling.
Fine cherry wood handles, shaped to correspond to the use of the knife.
Blade length 50mm
Saburrtooth 1/8'' Sphere - 3/8'' x 3/8''
Now available in Fine (yellow), Coarse (green) and Ex Coarse (orange).
Head Diameter: 3/8"
Head Length: 3/8"
Hard Arkansas Bench Stones
Prized by craftsmen worldwide, Arkansas Novaculite is the only known substance that can sharpen a blade and polish it as well. All of these Bench Stones are 100% natural Novaculite, cut to size and skillfully finished to ensure precise flatness.
The recommended stone for work that requires a smooth polish, but not the finest polish. This stone will provide a final hone and polish edge.
All bench...
Handles for Veritas Low-Angle Block Plane
The bevel-up configuration of the Veritas low-angle block plane lets you vary the blade angle to suit the task, from low-angle blades for use on end grain to high-angle blades on figured wood. However, steeper cutting angles require more force to push the plane—a challenge for those with small hands or less strength.
We offer inexpensive hardwood grips to adapt our low-angle block plane into...
Dutch Tool Chests
by Megan Fitzpatrick, with a foreword by Roy Underhill
''Dutch Tool Chests'' gives you the in depth instruction you need to build your own slant lid tool chest – from choosing materials, to the joinery, the hardware, the interior parts that hold your tools and the paint.
At the same time, the book offers you detailed instructions on how to grow as a hand tool woodworker....
Veritas Jointer/Edger
This jointer/edger can be used on cabinet scrapers, scraper plane blades, handsaws and ski edges.
It has a 45° jointing capability as well as the standard 90°. The handle has a comfortable, ergonomic shape and the screws are designed so they can be tightened with a small coin (to accommodate skiers).
In the shop, it is invaluable for jointing scrapers and handsaws; the fence is relieved next...
Kitchen Think
A guide to design and construction, from refurbishing to renovation
.png "Last Ones!")
Bessey KR Body Clamp 600mm
For parallel jaw clamping.
* now with 40% more clamping force (7000 N)
* depth increased from 85mm to 95mm
* supplied with 3 supporting pressure caps for extra protection
* with quality 2-component handle
* attach KR-AS adaptors for extra reach
KR60-2K 600mm opening 95mm depth
KR80-2K 800mm opening 95mm depth
Lie-Nielsen Honing Guide Chisel Jaw Pair
The Lie-Nielsen Chisel Jaws fit their 1/8" and 3/16" Bevel Edge Chisels (as well as the 1/4" to 3/4" Bevel Edge Chisels).
Replacement Blade for Nakaya Dozuki Classic Saw
A replacement blade for the Dozuki Classic dovetail saw.
0.3mm thick blade with very fine back teeth. Especially suitable for cutting tenon shoulders and precise wood joints.
Robert Sorby Traditional Bevel Edged Chisel
Traditional "carver" style boxwood handle with brass ferule and leather washer.
Overall Size 265 - 340mm
Blade Length 127-178mm
Kutzall 1/8'' Taper Burr - 1/8'' x 7/8''
Kutzall burrs are the perfect companions for your rotary carving tools.
Made in the USA, Kutzall burrs provide a great combination of material removal and surface quality. Efficient with or against the grain, these burrs have a long wear life.
Their outstanding performance on a wide variety of materials to include wood, plastic, rubber, fibreglass and soft stone.
NOTE: These burrs should only...
Gyokucho Razorsaw 291 Compact Ryoba 180mm
Full Name : Gyokucho Razorsaw Compact Ryoba.
Blade Length : 180mm.
Overall Length : 390mm.
Max Cutting Depth : N/A.
Teeth Pitch / TPI : Crosscut 1.5mm / 16.9. Rip Cut 3.7-2.7mm / 8-9.
Blade Thickness : 0.5mm.
Cutting Width : 0.81mm.
Teeth Pattern : Crosscut & Rip Cut.
Gyokucho Product Number : 291.
Weight : 160g.
Replacement Blade : S291
The compact range of saws can...
Gyokucho 293 Compact Kataba Atsuba 180mm
Full Name : Gyokucho Razorsaw Compact Kataba Atsuba.
Blade Length : 180mm.
Overall Length : 390mm.
Max Cutting Depth : N/A.
Teeth Pitch / TPI : 1.5mm / 16.9
Blade Thickness : 0.5mm.
Cutting Width : 0.81mm.
Teeth Pattern : Crosscut with some rip cut teeth.
Gyokucho Product Number : 293.
Weight : 160g.
Replacement Blade : S293
The compact range of saws can do much the same...
Nakaya Ryoba Gold Saw
The Nakaya Ryoba Gold is a great universal saw for your workshop. Ryoba refers to the saw being double edged, so one side with cross-cut teeth, the other rip-cut. A choice of 4 sizes........
Ryoba Gold 220mm.
220mm long, 0.4mm thick blade.
Set (Kerf width) 0.7mm.
Tooth spacing / teeth per inch cross-cut: 1.3mm or 19.5 TPI (teeth per inch).
Tooth spacing / teeth per inch rip-cut: graduated from...
Veritas Medium Router Plane
Slightly larger than the Veritas small router plane, this tool has the advantage of using the same blades as our full-size router plane.
For general use, the blade may be positioned inboard with the sole encircling it for maximum registration on the workpiece, even when approaching from the side or working an edge. This allows it to bridge recesses, providing great stability even on narrow stock....
Pfeil Medium Sized Tools - Series 9
Pfeil Medium Sized Tools are for smaller hands and beginners tackling basic projects. They have exactly the same quality and features as the Pfeil full sized tools.
These are the Pfeil Medium Sized Gouges.
Sweep ranges from series 2 to series 11. The higher the series, the deeper the sweep.
Widths range from 1mm to 14mm.
Brusso Brass Ball Catch BC-265
The Brusso BC-265 brass morticed ball catch, consisting of a brass cylinder with spring-loaded steel ball and a brass keeper, is used to secure cabinet doors. The grooved sides of each half, measuring 11/32" in diameter, provide grip when mounted and a reservoir for glue.
Diameter: 0.344" - 11/32" - 9mm
Translucent Arkansas Bench Stones
Prized by craftsmen worldwide, Arkansas Novaculite is the only known substance that can sharpen a blade and polish it as well. All of these Bench Stones are 100% natural Novaculite, cut to size and skillfully finished to ensure precise flatness.
The rarest of Arkansas sharpening stones. Translucent stones in their purest form are white. Translucent stones may contain shades of pink, yellow, and...
Cut & Dried
By Richard Jones
Serious woodworkers have long been starved of accurate information on wood technology that's explained in language for artisans - instead of for scientists.
Author Richard Jones has spent his entire life as a professional woodworker and has dedicated himself to researching the technical details of wood in great depth, this material being the woodworker's most important...
DMT Diamond Dia-Sharp Credit Card Sharpener
Take your sharpening anywhere with the portable Dia-Sharp® Credit Card Diamond Sharpener. Fitting easily into any pocket or wallet, it also comes in a convenient, grit color-coded vinyl carry case.
Available in 3 grits:
Coarse (45 micron / 325 mesh) to quickly restore a neglected edge.
Fine (25 micron / 600 mesh) to hone a razor sharp edge.
Extra-fine (9 micron / 1200 mesh) to refine a razor...
Lie-Nielsen Dowel Plates
If you want to make exact-sized dowels from any wood you choose, a Lie-Nielsen Dowel Plate is the best tool.
It's also handy to get a precise tenon on chair spindles. The Lie Nielsen plates are 1/4" x 5-5/8" x 1½" surface ground A2 tool steel. The holes are machined with 6-degree clearance taper on the underside, the holes are straight for the first .025"; so this tool can be sharpened many times...
Robert Sorby Timber Framer's Slick
This heavy duty timber framers and boat builders slick from Robert Sorby has an offset blade to allow for clearance when working in deep sockets and mortises. It can also be used as a massive paring chisel. Choice of two widths - 2-3/8" (60mm) & 3-3/8" (85mm).
Solid one piece forged blade including the heavy tang which is set deep into the handle. A heavy duty socket is fitted between...
Joseph Marples Trial 1 - Combined Marking & Mortice Gauge - Rosewood
The Joseph Marples Trial 1 Screwslide Marking and Mortice Gauge has a full 1/8" thick brass face.
The stock is locked on to the stem by brass knurled thumbscrew and protective pressure pad. The locking screw is set within a traditional brass protective shield.
A screw slide gives fine and precise adjustment of the mortice pins and on the back of the stem is a single marking gauge pin.
Veritas Apron Plane + PM-V11 Blade
This small, low-angle block plane from Veritas is the answer to a trim carpenter's prayers. At only 14oz it is half the weight of a standard block plane, a significant factor if you want to carry it with you all day.
The 5½" long, tough ductile cast iron body will take job-site accidents in stride. This is not a plane body that will break when dropped. It has good hand feel; the unique side...
Veritas Marking Gauge Replacement Wheel - (Inside)
Replacement wheel for the Dual Marking gauges. Both the Inside and Outside cutters are required for the Dual Marking gauge.
Hamlet Bowl Gouge
Milled from round bar. Every Hamlet bowl gouge is finely turned for making the best of turned bowls, for heavy profile cuts or delicate feather cuts.
Mastercarver 3 Piece Knife Set
Mastercarver® has improved the handle comfort of their popular 3 piece knife set. The naturally shaped hardwood handles will fit your hand better for superior grip and comfort. Perfect for right or left-handed use. The handles are lightly finished with natural Tung oil. Unlike ordinary varnish used on others, Tung oil prevents skin blistering and discomfort.
The blades are the 3 most popular...
Veritas Dovetail Markers
For quick, accurate marking of dovetails, this pair of Veritas Dovetail Markers are the best available. With riding ledges on both sides, these 50 x 50mm markers can be flipped over to scribe both slopes of the dovetail.
They are designed so the entire ledge is riding on the reference face, even when marking edge dovetails.
The relieved corners at the join of the body ensure perfect seating....
The Woodworker:
The Charles H. Hayward Years Vol. I - Tools
The Charles H. Hayward Years Vol. I - Tools
There is little doubt that Charles H. Hayward (1898-1998) was the most important workshop writer and editor of the 20th century. Unlike any person before (and perhaps after) him, Hayward was a trained cabinetmaker and extraordinary illustrator, not to mention an excellent designer, writer, editor and photographer.
Add to all that the fact that Hayward was, according to Robert Wearing, a "workaholic,"...
Lee Valley Glue Pot
We saw this little glue pot on the Lee Valley website, and we could not resist...........
Part of the reason heat sensitive hide glue is useful for furniture construction is because it can be softened for repairs; however, this property also makes it necessary to keep the glue warm while you work with it. This double boiler pot surrounds the inner pot with water to evenly distribute heat and help...
Pfeil Medium Sized Tools - Series 7
Pfeil Medium Sized Tools are for smaller hands and beginners tackling basic projects. They have exactly the same quality and features as the Pfeil full sized tools.
These are the Pfeil Medium Sized Gouges.
Sweep ranges from series 2 to series 11. The higher the series, the deeper the sweep.
Widths range from 1mm to 14mm.
Veritas Tongue-Cutting Blades for Combination & Small Plough Planes
All blades are made from A2 tool steel. Blades are made in Canada. These blades are suitable for both the Veritas Small Plough Plane and Veritas Combination Plane.
With these tongue cutters, you can now use our small plough plane for tongue-and-groove work. The blades are used in conjunction with our wide-blade conversion kit (see above), creating an interchangeable blade system that enables you...
Shinwa Mini Ink Line
Professional quality, compact Sumitsubo.
Body 130 mm, line length 15 m.
No ink is included.
New design (shiny new colours!)
Abranet Single Sided Sanding Pad
A 70mm by 125mm single sided moulded sanding pad designed to be used with smaller sanding strips. Black gel foam with one side velcro backed.
Ray Iles 6' Small Draw Knife
The Ray Iles 6" drawknife is a standard carpenter's drawknife, made from 01 high carbon steel and fitted with beech handles and brass ferrules.
Made in England
Grobet Auger Bit File
Auger bit files are double ended, with one end having teeth cut along the face with uncut edges, and the other with teeth cut along the edge and uncut faces.
This version, made by Grobet in Italy is very nicely made, with each end of the file tapered in two dimensions, and a finely shaped centre section to grip when working.
Length 7'' - Steel (8oz)
Made in Italy by Grobet
The Woodworker:
The Charles H. Hayward Years Vol. IV - The Shop & Furniture
The Charles H. Hayward Years Vol. IV - The Shop & Furniture
There is little doubt that Charles H. Hayward (1898-1998) was the most important workshop writer and editor of the 20th century. Unlike any person before (and perhaps after) him, Hayward was a trained cabinetmaker and extraordinary illustrator, not to mention an excellent designer, writer, editor and photographer.
Add to all that the fact that Hayward was, according to Robert Wearing, a "workaholic,"...
James Krenov:
Leave Fingerprints
Leave Fingerprints
By Brendan Bernhardt Gaffney
James Krenov (1920-2009) was one of the most influential woodworking writers, instructors and designers of the 20th century. His best-selling books – starting with “A Cabinetmaker’s Notebook” – inspired tens of thousands of people to pick up the tools and build things to the highest standard.
Yet, little is known about his life, except...
Veritas Vice Handle
A wooden handle from Veritas that fits both their Tail Vice Screw and their Front Vices.
Handle length 310mm and diameter of 30mm
Muzzles for Veritas Bench Dogs & Pups
For clamping a finished piece without marking it, the slip-resistant muzzles slide over the Bench Dogs (or Bench Pups) to give you a non-marring surface. They have a hard, spring-grip, plastic body with six face ribs.
Available in two sizes: 1¼" long for Bench Dogs or 3/4" long for Bench Pups. Sold in pairs.
Shaving Horses, Lap Shaves, and Other Woodland Vices
By Sean Hellman
Sean's book contains over 400 colour photographs and illustrations to demonstrate all stages and processes of making, using, and celebrating these traditional wood-braking devices.
It also provides plans and techniques that span instructions for beginners, to more complex designs, tool use and repair, and contemporary variations on traditional designs.
From the foreword written...
Brusso Brass Offset Pivot Hinge L-97
The Brusso L-97 offset pivot hinge is employed when a minimum of visible hardware is desired or when the door must swing free of its frame. It is morticed into the top and bottom of the door and frame; only the pivot is visible. The leaf measures 3¼" x 3/4" x 5/16".
Length: 3.250" - 3¼" - 83mm
Width: 0.750" - 3/4" - 19mm
Leaf Thickness: 0.313"...
Lie-Nielsen No.7 Jointer
The Lie-Nielsen No.7 Jointer Plane is a great plane for edge jointing and flattening larger areas.
The late, great Alan Peters used his No.7 for pretty much everything, and today we still come across ex-students which still favour their jointer over any other plane.
The equivalent of a later type Stanley Bedrock No.607 jointer plane.
22" (558mm) long.
2 3/8" (60mm) wide blade....