Sort By
Per Page
View
Grid
List
Peacock Oil (Low Odour) - Clear Honey - 100ml
Skelton Saws Peacock Oil is a wood finish made up of a mixture of traditional oils, resins and waxes, each adding its own special benefit. All ingredients are naturally obtained, mainly from ancient tree species and all have been time proven wood preservatives used by the Egyptians and Ancient Greeks. Both breathable and water-repellent, unlike current commercial finishes, Peacock Oil is built up from...
Peacock Oil (Low Odour) - Clear Honey - 250ml
Skelton Saws Peacock Oil is a wood finish made up of a mixture of traditional oils, resins and waxes, each adding its own special benefit. All ingredients are naturally obtained, mainly from ancient tree species and all have been time proven wood preservatives used by the Egyptians and Ancient Greeks. Both breathable and water-repellent, unlike current commercial finishes, Peacock Oil is built up from...
Robert Sorby Sandmaster 2'' Sanding Discs
Robert Sorby Sandmaster 2" velcro sanding discs.
Aluminium Oxide. Supplied in packs of 10
Veritas Bar Gauge Heads
Compares measurements e.g. equal diagnosis in drawers.
Transfers dimensions without converting into numbers.
Can be used for sizing shelves or interior trim on windows.
Gauge head openings are 13 x 19mm, rip 6mm slices to make bars (wood not included).
Greenwood Spoon Carving
By: Emmet Van Driesche
Carving a spoon from a piece of freshly harvested wood is a rewarding – and challenging – pastime. Tremendous knowledge about the properties of wood, and grain, and the use of sharp edge tools can be gleaned through this seemingly simple practice. There is more to it than meets the eye.
But many would-be spoon carvers don’t know where to begin. What...
Honest Labour:
The Charles H. Hayward Years
The Charles H. Hayward Years
“Honest Labour” is a collection of essays from The Woodworker magazine while the legendary Charles H. Hayward was editor (1936-1966). This book will be the fifth and final volume in the Lost Art Press series from The Woodworker.
When Lost art Press started on The Woodworker project more than a decade ago they didn’t intend to publish “Honest Labour.” The series was...
Lie-Nielsen Chipbreakers
Fits Lie-Nielsen No. 3 Bench Planes.
Lie-Nielsen chipbreakers are made of High Carbon Tool Steel and are 1/8" thick with a .015" lip ground at a 2 degree angle to provide excellent contact between the leading edge of the chipbreaker and the blade. Very solid. Supplied with the chipbreaker screw.
* 1-3/4" wide
Lie-Nielsen chipbreakers are designed specifically for their tools. It is possible...
Pentel Ain Stein - 0.7mm tube of 40 HB leads
About 10% stronger than any other Pentel refill lead thanks to a ceramic cell structure
Supplied in easy to dispense, swivel-top tubes
Smoother than other refill leads on the market
Suitable for all 0.7mm mechanical pencils
40 leads per tube
Made from 92% recycled material
Lie-Nielsen Chisel Handles
Lie-Nielsen chisel handles are made from Maine-harvested Hornbeam and can be used with any of the Lie-Nielsen chisels.
The standard handle is recommended for all but the largest chisels.
Long chisel handles are 4" longer than the standard handles. Excellent for paring.
The Mortise chisel handles are slightly larger in diameter and length than the standard chisel handle, the Mortise Chisel Handle...
Gransfors Bruk Large Splitting Axe 445 - Long 31'' Handle
The same as the Gransfors Large Splitting Axe 442 but with a longer 31" hickory handle. Ideal for taller users or when more power is required.
Danger: Always wear adequate clothing and protection for your face and eyes.
The poll of this axe, like the poll on most axes, is definitely not designed for heavy pounding on a wedge.
The axe has a 3" face and a 31" hickory handle and weighs just...
The Joiner & Cabinet Maker
The Joiner and Cabinet Maker" has more than 370 pages of detailed handtool instruction, including many processes that have not been covered before in the early woodworking literature. In 1839. In that year, an English publisher issued a small book on woodworking that has – until now – escaped detection by scholars, historians and woodworkers.
Titled "The Joiner and Cabinet...
Hamlet Standard Spindle Gouge
These are tools for working between centres on parallel grain. For beads, coves and profile work on vases, cups and shaped work.
Lee Valley Scratch Awl
Most scratch awls have a round handle, which makes it easy for them to roll off a bench. We designed this one with a 3" long hardwood handle with two flats to ensure it does not go anywhere when you lay it down.
The 5" long tapered blade is dressed to a fine point for precise marking and layout.
Hardened to Rc55, the high-carbon steel blade does not dull quickly.
Made in Canada.
Thomas Flinn Pax Flexible Flush Cutting Saw 20tpi
The Pax Flexible Flush Cutting Saw has a very flexible alloy steel bade which cuts on the pull stroke. As it has no set, this saw is excellent for use in cutting dowels etc. as you can get the saw right to the edge with out leaving a very smooth surface.
The saw has a brightly polished brass back and a Walnut handle. Blade length 6". 20tpi as standard. Individually blister packed.
Mortise & Tenon Magazine - Issue 17
The Table of Contents for Issue 17 of Mortise and Tenon Magazine is
Andrew Hunter – “Finding a Path”
Michael Updegraff – “The Light Within: Restoring Wooden Sash Windows”
Edward Bouvier – “A Communal Legacy: Handcraft as Part of a Holistic Education for Life”
Narelle Freeman – “Secrets Beyond Our Reach”
Joshua A....
Veritas Shooting Board
The 24" long shooting track fits the Veritas shooting plane.
This is a shooting board that doesn’t limit you to one angle, the fence is adjustable to let you shoot up to 60° from square. A spring-loaded button registers in fixed detents at 0°, 18°, 22.5°, 25.7°, 30°, 36°, 45° and 60° to let you quickly set the fence for square angles as well as miter cuts to produce frames with ten,...
Spare Blade for Lie-Nielsen No. 62 Low Angle Jack Plane
Replacement blade for the Lie-Nielsen No. 62 Low Angle Jack Plane.
The blade comes with a 25° flat ground bevel; it sits in the tool at 12°, making the included cutting angle 37°.
The blade comes ready to use, but honing a secondary bevel of 5° or 10° will increase performance, help achieve a razor edge quickly, and improve edge life in hardwoods.
* 2" wide x .175" thick
* A2 cryogenically...
Blue Spruce Round Mallet
Blue Spruce Round Mallets feature a maple head infused with a tough polymer resin that increases the density of the maple by 80%. The infused head puts more “smack” into less space than simple wooden headed mallets. In addition to concentrating power, the resin protects the wood fibers from compression. This beautiful tool will still look beautiful after chopping hundreds of dovetails and...
Veritas Scraper Holder
There is no tool handier in the workshop than a cabinet scraper, and this holder lets you use it to maximum advantage.
The light, strong, glass-filled nylon body, with all brass fittings, is kind to a sharp hook. You can slip any thickness of scraper (6"/150mm long) into it, clamp it in position, and set the amount of bow with the screw-actuated centre pad.
The body is moulded to fit your hands...
Bessey XV5-170 VarioClippix Spring Clamp
* Variable clamping width up to 170 mm‚ yet can be operated with one hand
* Lightweight‚ functional and easy to handle
* Extremely stable
* Retail-ready packaging
Gransfors Bruk Scandinavian Forest Axe 430
A profesional axe for those who want to limb a felled tree in a traditional way. Forged to a thin, curved "bit" and sharpened to make it suitable for cutting branches in fresh, resinous wood, spruce or pine. The long handle gives extra strength and power to the cut. The axe has a 3½" face and a 25" hickory handle and the head weighs 2 lb.
Book and protective leather sheath included.
Spare Blade for Lie-Nielsen No. 102 Low Angle Block Plane
Replacement blade for the Lie-Nielsen No. 102 Low Angle Block Plane.
The 1¼" wide 1/8" thick A2 steel blade comes with a 25° flat ground bevel.
Brusso Brass Jewellery Cabinet Pull MC-428
The Brusso MC-428 brass decorative knob, with a flattened dome face ringed by a band-shaped edge, is pressure-fit and glued into place. It measures 3/8" in diameter and projects 7/16". The mounting dowel is 3/16" in diameter.
Diameter: 0.375" - 3/8" - 9.5mm
Length: 0.436" - 7/16" - 11mm
Saburrtooth 1/8'' Cylinder - 1/4'' x 1/2''
15% discount from price shown.
Veritas Small Plough Plane
This is Veritas' redesigned small plough plane. While it still excels at cutting grooves, rabbets and tongues, it now has the ability to cut decorative beading (beading blades available soon).
Closest in size to the classic Record #044 plane, the preferred size of the old-style plough planes, it has a 6 5/8'' long fence that registers solidly to the workpiece and is through-drilled...
Pfeil Back Bent Gouges Series 25
Pfeil Back Bent Gouges are for carving convex surfaces that are hard to reach, and for clean finish cuts.
The tools range from Least Convex to Most Convex: 10 - 20 - 30 - 25 - 28.
Please note that series 25 and 28 are more convex than 30.
Spare Blade for Lie-Nielsen No. 4 and 5 Plane
Replacement blade for Lie-Nielsen No. 4 or 5 Bench Planes.
A2 Steel, Cryogenically treated, hardened to Rockwell 60-62 and double tempered. Lie-Nielsen heat treating technique ensures that the blade will take and hold a very fine edge for a long time. After heat treating, the blade is fully surface ground on the top, back, and cutting edge, giving a smooth, flat surface that will take a mirror...
MoraKniv Single Edge Spoon / Hook Knife - 164 Left Hand
This new re-designed Mora knife is ideal for spoon and bowl carving. This model has a single cutting edge optimised for left handed use. So if you held it in your left hand it would cut on the pull. It can be used in the right hand but would require a push stroke away. The 164 has a tight curve.
Mora changed the design with input from renowned craftspeople Jögge Sundqvist and Beth Moen, with...
Veritas Skew Block Plane + PM-V11 Blade
The Veritas Skew Block Plane is a versatile plane that excels at trimming rebates and planing end grain. Of course, you can also use it as a normal block plane. Its Norris-style adjuster guarantees precise blade setting. Machined and surface ground, the 162 x 44mm body is ductile cast iron. It has a 12° bed angle and a movable toe fully enclosed by the body casting. A Bubinga knob locks the toe...
Pfeil Medium Sized Tools - Set of 4
Pfeil Medium Sized Tools - Set of 4 come in a plastic slip case and includes:
1 x Chip Carving Knife;
1 x Straight Chisel: 8mm (D1-8);
1 x Gouge: Series 8 - 7mm (D8-7);
1 x 60° V-Tool: 6mm (D12-6).
Size 260 x 130mm
Weight 160g
Beech
Beech is not toxic, meaning it is particularly suited for household and kitchen items.
Carved spoons in beech are common as well as bowls and platters.
Naturally white with a pinky-red heart called ‘Kern’. Often beech may have characterful mineral streaks in the timber.
Peacock Oil (Low Odour) - Antique Amber - 100ml
Skelton Saws Peacock Oil is a wood finish made up of a mixture of traditional oils, resins and waxes, each adding its own special benefit. All ingredients are naturally obtained, mainly from ancient tree species and all have been time proven wood preservatives used by the Egyptians and Ancient Greeks. Both breathable and water-repellent, unlike current commercial finishes, Peacock Oil is built up from...
Pfeil Hornbeam Mallets
Pfeil Hornbeam Mallets are the perfect choice for woodcarvers seeking durability and precision in their tools. Expertly turned from a single piece of high-quality Hornbeam, these mallets offer exceptional balance and control, ensuring every strike is accurate and effective.
Solid Hornbeam Construction: Crafted from a single piece of Hornbeam, these mallets are built to withstand rigorous use...
Famag Extension Shanks
Perfect for drilling deep holes.
The Ø 8mm shanks are suitable for FAMAG Fortsner bits up to 22mm (7/8").
The Ø 10mm shanks are suitable for FAMAG Fortsner bits 22mm (7/8") and larger.
The Forstner bits we stock are 90mm tall from tip to tip, which gives you a working depth of 57mm.
Four attachment screws for fixing.
13mm shank has three clamping surfaces.
Suitable for...
Pegas Spiral Blades
Pegas Spiral Scroll Saw Blades (plain end) allow cutting around the entire periphery of the blade due to a helical shape. This design allows work to be fed in straight moves. The work does not have to be turned to make cuts, so sharp inside corners can be created. Excellent for wood, plastic, ferrous metals, nonferrous metals, bone, wax and more.
5" (130mm) in length and supplied in packs of...
Crucible Engraving Tool
The Crucible Engraving Tool is a simple, easy-to-use tool that allows you to slice straight and curved decorative lines on almost any wooden surface. The Engraving Tool was designed to create geometric patterns found on old Scandinavian and Eastern European furniture. But we found it also is excellent at carving modern geometric patterns.
The Engraving Tool consists of two pieces: a handle and a...
From Truths to Tools
By Jim Tolpin and George Walker, Illustrated by Andrea Love
Good books give you a glimpse of small truths - about workbenches, joinery or sharpening, for example. Great books, on the other hand, stitch together seemingly disparate ideas to present a new way of looking at the whole world, from your marking awl, to your hand or to the line of the horizon.
"From Truths to Tools" is a hand-illustrated...
Kirjes Bowl Sander - 40 x 40mm Ball Drum
This Kirjes Ball Drum Sander is 40 x 40mm.
Comes with one 220grit sleeve. Additional sleeves available separately.
Every sanding sleeve is made to specifically fit each inflatable sander. On the round sander, the overlapping design of the sanding sleeves is to ensure longevity and optimum effectiveness in awkward places.
Shaft diameter 6mm.
Lee Valley Small Double Square
This is an excellent tool for precise layout work and machinery set-up. Made entirely from stainless steel, the square includes two 2 1/2'' long rules with etched and black-filled markings for legibility.
The standard rule is graduated on one face in 32nds and 64ths. The narrow (0.2'' thick) rule, with a 1/2'' long probe on one end, is designed for access into confined spaces,...
Pfeil Series 2a - Spoon Bent Gouge
For shaping recesses and working in corners.
.png "Last Ones!")
Henry Taylor No.5 Fishtail Gouges
This range is being discontinued by the supplier, only available while we have stock.
From the "Professional" range of Henry Taylor carving tools. These fishtail gouges have a 4¾" (120mm) blade with a ground inner surface and a charcoal black non-reflective finish on the outer surface. Fitted with an octagonal beech handle and brass ferrules.
A copy of the Henry Taylor sizing...
Arbortech Ball Gouge
The Arbortech Ball Gouge is a unique tool designed for power carving. It has a cutting ring on a 30mm spherical ball with a 90mm arm that attaches to any standard 100mm (4") or 115mm (4½") angle grinder. The cutting action produces fine shavings rather than dust.
This ball gouge gives you the ability to make smooth hollows and concave recesses in spoons or small bowls and safely undertake freehand...
Hock Marking Knife Blades
This right or left hand, spear point marking knives (bevels are on one side only) are perfect for scribing fine lines against a straight edge.
High carbon steel. All steel knife.
Veritas Bevel-Up Smoother Plane + PM-V11 Blade
The latest addition to the Veritas family of low-angle bench planes is the state-of-the-art pure smoothing plane. It is the plane to use for the final finish on surfaces, especially woods of difficult grain patterns. It also complements the low-angle jack plane.
Veritas have combined the generous width and weight of a dedicated smoother with the versatile inner workings of a low-angle bevel-up...
Pfeil Carpenter Chisel Sets
Introduced in 2010 from Switzerland, Pfeil Carpenters Chisels have strong Elm wood octagonal handles with an oval section. We prefer these to the bench chisels.
The blades are forged from K 510 steel, hardened up to 60 RC. Bevel edged with well marked facets. The blades are finely ground and polished.
Bevel angle 25°, razor sharp.
4mm wide to 40mm wide.
Overall length 240-260mm.
The...
Lynx Mini Scraper Set of 4
The Lynx four piece Mini Scraper Set is the perfect way to smooth/remove wood and finish small areas.
This set has the following shapes included:
Mini gooseneck - good for curved areas
Mini oval - good for curved areas
Mini square - good for a variety of straight edges for a wide and even has notches in which is good for luthier work ie acoustic bridge saddle crowning
Mini Concave/Convex - good for...
Mortise & Tenon Magazine - Tenth Anniversary Issue (Issue X)
This is a pre-order, stock will not arrive until July.
Anything ordered at the same time will be held until Issue X arrives.
Hock Metal Spokeshave Blades
2 .1/8'' Cutting Edge.
Hock Replacement blades for metal spokeshaves (Type 151) - cryogenically treated A2 blades.
Perhaps the most dramatic improvement can be realised by accurizing and tuning your Spokeshave. It is a mediocre tool as it comes from the factory, but with a quality blade and a little fussing, it becomes a versatile and sensitive tool capable of doing fine work. Stanley...
![Union No.42 Tongue & Groove Plane [Preowned, SOLD]](/images/products/thumbs/3823_9649.jpg "Union No.42 Tongue & Groove Plane [Preowned, SOLD]")
![Union No.42 Tongue & Groove Plane [Preowned, SOLD]](/images/products/thumbs/3823_9647.jpg "Union No.42 Tongue & Groove Plane [Preowned, SOLD]")
