Sort By
Per Page
View
Grid
List
Hamlet Rolled Edge Radius Skew Chisels
A combination of radius skew and rolled edge for steadiness on the tool rest without fear of drag.
Robert Sorby Fingernail Profile Spindle Gouges
Robert Sorby fingernail profile spindle gouges are ideal for fine detailing on spindle work. The wing tips are ground back to reduce the danger of catching when working in confined areas.
Robert Sorby Fingernail Profile Bowl Gouges (Deep Flute)
The profile of this Robert Sorby Fingernail Profile Bowl Gouge increases the flexibility allowing a woodturner to perform "pull cuts" without catching the lathe bed. The greater cutting tip area allows for both delicate shearing cuts and for heavy profiling cuts.
Robert Sorby Spindle Roughing Gouges
Robert Sorby spindle roughing gouges are for initial turning of uneven or square stock to round. The shape of the roughing out gouge enables the tool to cut safely with the wings (the name given to the tips of the side walls) well back from the workpiece.
Robert Sorby Standard Bowl Gouges (Deep Flute)
The Robert Sorby standard bowl gouges are a must in the tool kit of every bowl turner.
These tools are ideal for making bowls, capable of producing either massive profiling cuts or delicate finishing cuts as necessary.
Hamlet Bowl Gouge
Milled from round bar. Every Hamlet bowl gouge is finely turned for making the best of turned bowls, for heavy profile cuts or delicate feather cuts.
Robert Sorby Standard Spindle Gouges
Robert Sorby spindle gouges are detailing tools used on between-centre work, where the grain is running parallel to the lathe bed. They are used to create coves, beads, and other profiles on goblets, vases and egg cups.
Square End Scrapers
The Robert Sorby square end scrapers are used for finishing convex and flat bottomed forms. The end profile can be modified to a specific shape as required, eg diamond point.
Robert Sorby Standard Parting Tools
Robert Sorby standard parting tools are used to part the finished project off from the waste material, the parallel sides make for a rigid tool that handles well. The 1/8" (3mm) tool reduces the amount of waste, vital if the timber is an expensive, exotic one.
It also makes for a fine detailing tool, e.g. beads and fillets.
Hamlet 1/16' Parting Tool
Parting tools are mostly used for cutting through or forming shoulders, and are essential in any workshop.
Robert Sorby Standard Skew Chisels
Robert Sorby standard skew chisels are rectangular in section, giving this type of of skew more weight. This makes them superb for large spindle work e.g kitchen table legs and newel posts.
Hamlet Oval Skew Chisel
Finely balanced tool designed to allow the tool ease of movement along the tool rest producing a clean fine finish without the fear of tool rest damage.
Hamlet Beading & Parting Tools
These beading and parting tools are used primarily for forming beads and spigots, these tools can also perform the standard parting tool tasks such as cutting through and forming shoulders.
Hamlet 3/16'' Diamond Parting Tool
The Hamlet diamond parting tool is not made from diamonds, sorry to disappoint! It refers to the diamond shaped profile which reduces friction, and therefore heat to avoid unwanted burn marks, or even splitting. The shape also reduces the risk of binding in the cut.
Bead Forming Tools - 835H
Bangles and curtain rings are just two of the projects which can be undertaken with the use of Robert Sorby ring cutting tools. They can also be used to adorn stems with captive rings. Unlike some simular tools, the original Robert Sorby ring cutting tools are designed in such a way that sharpening and repeatability are not compromised.
All tools are supplied with full use and sharpening instructions.
Beading Tool Set
Robert Sorby bead forming tools to cut perfect semi-circular beads every time.
The nose design permits multiple bead designs.
This ia a boxed set of 5 RS-835H Bead Forming Tools 1/8", 3/16", 1/4", 5/16" & 3/8" .
Hamlet Big / Little Brother Cutter
1x replacement cutter that fits the Hamlet Big and Little Brother Hollowing Tool.
Hamlet Big / Little Brother Edge Protector
1x replacement edge protector that fits the Hamlet Big and Little Brother Hollowing Tool.
Hamlet Big Brother
Hamlet Big Brother is the complete set consisting of Multi Handle (26"), 1/2" cutter, edge protector and a 5/8" straight stem.
Does not include reducing collets, side handle or hollowing gate, but these are available separately.
Hamlet Detail Gouge
Detail gouge for very fine point work between spindles.
Hamlet Hollowing Gate
Available in 19mm (3/4") and 25mm (1"). Other stem sizes can be made to order, but will have a longer lead time.
Hamlet Little Brother
The Hamlet Little Brother has the same set-up as its Big Brother. So it has the same 1/2" cutter and edge protector. The difference is that the Small Brother has a smaller (17") handle and the 5/8" stem is tapered.
Does not include reducing collets, side handle or hollowing gate, but these are available separately.
Hamlet Parting Tools
Parting tools are mostly used for cutting through or forming shoulders, and are essential in any workshop. The 1/8 parting tool (HCT 090) is a popular starter tool.
Hamlet Rolled Edge Skew Chisels
A combination of flat skew and rolled edge for steadiness on the tool rest without fear of drag.
Hamlet Round Nose Scrapers
Hamlet round nose scrapers are used on concave surfaces such as bowls to leave you with a smooth finish.
Hamlet Side Handle
Will fit both Little Brother & Big Brother.
Hamlet Spindle Roughing Gouge
These are often simply referred to as roughing gouges but they are not to be used for roughing bowls. They are only for spindle work i,e roughing a square spindle to round.
Hamlet Standard Skew Chisel
Made from flat rectangular bar heavier than oval section for turning on legs, posts etc.
Hamlet Standard Spindle Gouge
These are tools for working between centres on parallel grain. For beads, coves and profile work on vases, cups and shaped work.
Hamlet Thread Chasers 18 tpi HSS (pair of)
Thread chasers by Hamlet Craft Tools in Sheffield, England.
These are tools used for chasing (this basically means cutting) a thread on your workpiece on your lathe and are made in matched pairs. One of the pair (the male or external thread) has its cutting 'teeth' at the end of the blade and is used for threading the outside of the workpiece, whilst the "female" has cutting teeth set at right...
Hamlet Thread Chasers 20 tpi HSS (pair of)
Thread chasers by Hamlet Craft Tools in Sheffield, England.
These are tools used for chasing (this basically means cutting) a thread on your workpiece on your lathe and are made in matched pairs. One of the pair (the male or external thread) has its cutting 'teeth' at the end of the blade and is used for threading the outside of the workpiece, whilst the "female" has cutting teeth set at right...
Henry Taylor Negative Rake Cove Tool
The Henry Taylor negative rake cove tool was designed to be used with The Decorating Elf but can also be used as an individual tool. When using with the Decorating Elf allows you to make coves.
Ideal for end grain work and spindle work.
Made with a high speed steel blade.
Henry Taylor Negative Rake Fine Point Tool
The Henry Taylor negative rake fine point tool was designed to be used with The Decorating Elf but can also be used as an individual tool.
Ideal for fine detail and is made with a high speed steel blade.
Robert Sorby 1/16' Slim Parting Tool
This Robert Sorby 1/16" handy parting tool is designed to give the cleanest and finest of cuts with the minimum of waste wood. Its 1¼" blade width eliminates the flexing and twisting normally associated with such a thin blade.
The double bevel HSS cutting face gives the very finest of cuts. For added security the blade is seated and riveted deep into the handle.
Robert Sorby 3/8' & 5/8' Bead Cutting Tip
The Robert Sorby Bead Cutter is one of a few additional cutters available for the popular Robert Sorby Multi-tip Hollowing Tool. This double sided cutter will cut beautiful beads on spindle work at 3/8" and 5/8" and is one of two beading cutters available for this tool.
Sharpening: Use a diamond file or honing stone flat across the top face. To gain best results and increase the longevity...
Robert Sorby 3/8' & 5/8' Cove Cutting Tip
The Robert Sorby Cove Cutting Tip is one of a few additional cutters available for the popular Robert Sorbyn Multi-tip Hollowing Tool.
Sharpening: Use a diamond file or honing stone flat across the top face. To gain best results and increase the longevity of the cutter this simple procedure should be done little and often.
This cutter is designed for use with the following tools:
Multi-tip...
Robert Sorby Beading & Parting Tool
The Robert Sorby beading and parting tool is a versatile tool used for parting off as well as producing beads. Its size makes it very stable, but also very sensitive in use. Ideal for creating the spigots to fit in a chuck.
3/8" Beading & Parting Tool - 18¾" with handle.
Robert Sorby Bedan Parting Tool
The Robert Sorby bedan parting tool is used in the same way as the beading and parting tool the relieved side bevel allows the tool to plunge cut in bowls and boxes with little risk of binding.
3/8" Bedan Parting Tool - 18¾" with handle.
Robert Sorby Box Scraper
The special cutting profile of this Robert Sorby box scraper makes it ideal for cutting the parallel side walls of end grain boxes. The small radius on the point at the bottom of the cutting section creates a smooth intersection between the side wall and the flat bottomed vessels. The profiles cause this to be very responsive and sensitive in use.
3/4" Box Scraper - 16" with handle
Robert Sorby Captive Ring Tool Set
This set of Robert Sorby Captive Ring Tools comes with tips capable of producing 3/16", ¼", 3/8", and ½" rings. These can be used on the stems or spindles of projects or may be used in their own right as items of jewellery, napkin rings, curtain ring or even wheels.
The set enables the turner to cut rings of the four above mentioned sizes with just one tool simply by switching over the tips....
Robert Sorby Chattertool - 215
Chattertool patterns add a neat, random decoration on end grain like box lids. These are created by using the Robert Sorby chattertool which comes with two different double-ended chattering tips and a handy scraper cutter. One chattertool tip (RS220) has a straight and a pointed end, the second (RS221) has a convex and a concave half-round end.
Chatter patterns are created by causing the spring...
Robert Sorby Continental Style Spindle Gouges
Robert Sorby continental style spindle gouges have a wonderful reputation for superb handling when doing spindle work.
Robert Sorby Curved Scraper
The curved end profileof thie Robert Sorby Scraper makes this excellent for creating, smoothing and blending curved surfaces in bowl and spindle work, eg round bottomed boxes. This new tool is able to take an agressive cut, whilst retaining the butterfly sensitivity for the refining cuts.
3/4" Curved Scraper - 16" with handle
Robert Sorby Detail Point Tool - 822H
This is a 3/8" round shaft with a 3 facet point. Ideal for for fine detailing on bowl and spindle work.
Robert Sorby Diamond Section Parting Tool
The special profile of this Robert Sorby diamond section parting tool reduces the risk of binding in the cut. It also reduces the amount of heat build up caused by friction, thereby reducing the chance of burning the bottom of the parted project.
3/16" Diamond Parting Tool - 17" with handle.
Robert Sorby Diamond/Side Cut Scraper
The Robert Sorby diamond/side cut scraper can be used on square bottomed boxes the end profiles allows the tool to create a right angled juncture between side wall and bottom. The 85º angle at the end prevents the tool from cutting th eside wall and the bottom at the same time.
3/4" Diamond/Side Cut Scraper - 16" with handle.
Robert Sorby Easybeader - 814H
The Easybeader allows traditional beads to be formed whilst also offering the option of producing perfect half beads. Suitable for use with both spindle and bowl work.
The easybeader is a unique yet simple tool to cutting a series of consistent and regular beads. Originally conceived by a production turner it allows for easy replication of designs like bee-hive boxes, and honey dippers. Because...
Robert Sorby Fluted Parting Tool
This Robert Sorby fluted parting tool has a milled flute running along the bottom edge, creating two sharp spurs at the cutting face. These sever the fibres to produce a burnished finish. The tapered profile also reduces the risk of binding in the cut. The long bevel has a milled flute which is the cutting face. The small bevel his the sharpening face. When parting off, this unique arrangement causes...