Sort By
Per Page
View
Grid
List
Pfeil Series 14 - 55° Soft V Parting Tools
For carving lettering and ornamentation and for sculpting figures.
55°
Auriou Cranked Neck Curved Ironing Rasps
These are the Right Handed versions, to see the Left Handed please CLICK HERE.
These are very useful for working in small areas. The rasp is short and is curved along its length so you can enter your work easily.
The tang is cranked to allow knuckle clearance.
4 sizes and grains based on width:-
10mm wide Grain 12
15mm wide Grain 11
20mm wide Grain 10
25mm wide Grain 09
30mm wide Grain...
Henry Taylor Swan Neck Chisel 1/4''
A Henry Taylor swan neck chisel is used to clean the bottom of mortices. The chisel is levered in use, not struck.
Available in 1/4".
Replacement Blade for Nakaya Ryoba Gold Saw
Replacement blades for Ryoba Gold Saw.
A double edged blade with X-cut & rip edges and traditional style handle.
A choice of 4 sizes
220mm blade - 0.4mm thick (spacing of teeth 1.3mm cross 2.0-3.4mm rip cut setting 0.7mm) WRG220
240mm blade - 0.5mm thick (spacing of teeth 1.6mm cross 2.7-3.9mm rip cut setting 0.75mm) WRG240 - This is our most popular size.
270mm blade - 0.6 mm thick...
Table for 1 1/2'' Wheels for Veritas Grinder Tool Rest
This replacement table for the Veritas grinder tool rest has a wider slot to let you use it with 1 1/2" wide wheels (like 8" CBN wheels).
The 4" wide aluminum table has a 1 5/8" wide slot and installs easily in place of the standard table. It has the same horizontal slot and center hole for use with sliding and rotating jigs.
(For wheels narrower than 1 1/2", the standard...
Crucible Planing Stop
We have always loved blacksmith-made planing stops, which are embedded in the end of a block of wood that is about 3” x 3” x 12”. The block is friction-fit into a mortice in the benchtop and moves up and down with mallet taps.
In our experience, the planing stop is as important as the workbench’s face vice and has almost-endless uses.
The main problem with a blacksmith...
Lee Valley Replica Spill Plane
Before matches became widely available in the 1860s, long, coiled wood shavings known as spills were used to transfer a flame from one location to another, such as from a fireplace to a candle, lantern or stove. Typically made using a special inverted plane, spills burn more slowly and consistently than paper, and also double as a convenient tinder material. We based the design of our spill plane on...
Lynx Concave Scraper Set
The Lynx Concave Scraper Set contains 2 scrapers shaped specifically to scrape curved areas such as spindles, chair legs etc. The high grade steel used on these scrapers, has been cut with various concaved areas to suit different sized curves.
The recess areas are sized as follows:
Scraper 1 - 1/4", 3/8", 1/2", 5/8" and 6/8"
Scraper 2 - 7/8", 1", 1 1/8",...
Robert Sorby Woodworkers' Square Guide
This simple to use jig has been designed as an upgrade to the current woodworking chisel jig (PESQ). This jig can be adjusted to ensure exact and repeatable 90 degree angles can be achieved every time. A stepped plate raises the tool to be sharpened away from the tool platform.
Ideal for sharpening chisels and plane irons.
Kutzall 4 1/2'' Shaping Dish - Extreme
Made in the USA, the Kutzall Shaping Wheels provide a great combination of material removal and surface quality. Efficient with or against the grain, these wheels have a long wear life.
Their outstanding performance on a wide variety of materials to include wood, plastic, rubber, fibreglass and soft stone.
NOTE: These wheels should only be used on non-metallic materials.
The Shaping Wheels...
Shaker Inspiration
Five Decades of Fine Craftsmanship
Shinwa Combination Square 45°, 90° & 135° - Metric
Shinwa Combination Metric Square made of stainless steel includes a mitre gauge and square.
Measurements on both sides
Angular accuracy 45° & 135°: 0.2 mm or less per 100 mm
Angular accuracy 90°: 0.1 mm or less per 100 mm
Base length: 163mm
Veritas Shooting Board Track
These are straight, durable aluminium tracks for making your own shooting board. They are designed to fit the Veritas Shooting Plane, and any other plane with a running surface between 2-1/32" and 2-1/4" wide; you can adjust the stainless-steel outer rail for a perfect fit. Set screws keep the rail from shifting in use.
The inner rail is 11/64" tall. Low-friction UHMW strips in the...
Kutzall 1/8'' Sphere Burr - 3/8''
Kutzall burrs are the perfect companions for your rotary carving tools.Made in the USA, Kutzall burrs provide a great combination of material removal and surface quality. Efficient with or against the grain, these burrs have a long wear life.Their outstanding performance on a wide variety of materials to include wood, plastic, rubber, fibreglass and soft stone.NOTE: These burrs should only be used...
Blue Spruce Optima Mortise Chisels - Curly Maple
Blue Spruce Toolworks new Optima Chisels feature a lapped and polished back with a flatness measured in light bands (the same system used to measure silicon wafers). When you unbox your new Optima Chisels, they’re razor sharp and 100% ready to go to work.
Each Optima Chisel is machined from A2 tool steel, then double-tempered and cryogenically treated. The tempering and cryo treatments result...
Veritas Beading Blades for Combination & Small Plough Planes
All blades are made from PM-V11® tool steel. Blades are made in Canada. These blades are suitable for both the Veritas Small Plough Plane and Veritas Combination Plane.
These blades let you use the small plow plane to create decorative beading on workpieces. The blades are available in 1/8", 3/16" and 1/4" bead diameters. A 1/16" groove is cut on either side of the bead.
Making Traditional English Wooden Eating Spoons
By Eric Rogers
Learn how to make traditional English wooden eating spoons with Eric Rogers
Of all the materials used by our forefathers wood was undoubtedly the most common but is the least represented in museums today.
Churches and timber framed houses preserve some of the grander uses of wood but very few everyday artifacts survive.
Tens of thousands of wooden spoons must have been thrown...
Ash
Sourced from our mill friends in Yorkshire this is UK kiln dried ash supplied in squares with sealed edges.
There is some spalting which suggest that when worked these ash blanks may reveal some interesting features.
Everyone loves ash because it is a strong wood that is relatively straight forward to turn and that is take stain and finishes well.
Ash is a great wood for handles and other...
Hamlet Round Nose Scrapers
Hamlet round nose scrapers are used on concave surfaces such as bowls to leave you with a smooth finish.
Kirjes Polishing Cloths
Kirjes Polishing Cloths are an essential accessory for achieving a fine finish on your woodworking projects. Designed to be used with buffing sleeves, these cloths significantly reduce the time and effort required for sanding while delivering exceptional results. Available in different shapes and sizes, including short cylindrical, long cylindrical, dome, and short & fat cylindrical sanders, they...
Lie-Nielsen Cross Peen Hammer
This small hammer is not only great for tacks and brads, but also for making fine blade adjustments on your planes.
Brass Head, 4 oz (115 grams).
Cherry handle
Overall size is 12'' (300mm) long and 4'' (100mm) wide
Robert Sorby Bead Forming Tools - 835H
The Robert Sorby Bead Forming Tool has been designed for creating precise and consistent beads. Perfect for making decorative bangles, curtain rings, and adorning stems with captive rings, this tool ensures accuracy without compromising on ease of sharpening and repeatability.
Available in multiple sizes: 1/8", 3/16", 1/4", 5/16", 3/8", 1/2".
Includes full use...
Veritas String Inlay Tool System
Used much like a marking gauge, this inlay tool lets you accurately cut narrow grooves in a workpiece as well as neatly slice fine strings from a sheet of veneer. Its interchangeable blade system lets you quickly swap blades to suit the activity.
The hook-shaped blade is designed to cut grooves. Used in a sweeping push-pull motion, it has outlining spurs on one side of the blade to score the groove...
Veritas Tail Vice Screw
The tail vice screw is essentially the same construction as a shoulder vice screw but without an end guide, this tail vice screw has a clamping capacity of 17" less thickness of wooden jaws (not included) and is 21" overall.
1.1/8" diameter screw with single-lead Acme threads.
Mounting screws included.
Wooden Handle not included, but can be purchased as an optional extra.
Made...
Build a Chair from Bulls%$t
by Christopher Schwarz
Note: You can download a pdf of this book for free here from Lost Art Press and full-size patterns here. You won’t have to register or give up your email. Just click the link, and the book will download to your device. All copies are signed by the author.
Build a comfortable wooden stick chair using only materials and tools found at your home centre. No jigs, no...
Knew Concepts 6 1/2'' Coping Saw
On the Knew Concepts Coping Saw the blade is tensioned by a cam-lever and pulls so taut that the blade "sings" when plucked. Chris Schwarz said "...it's more like sawing with an unbendable wire than a floppy steel hotdog (which is what is typical of most saws)". Make turns that are tighter than ever before.
The solid steel indexing blade-hooks lock in eight 45° positions...
Lie-Nielsen 7 Tool Chisel Roll
7 pocket leather tool roll, Brass fittings. Beautifully made in Maine, USA.
Accessories for the Benchcrafted Drawsharp
Rehab kit
Most knives will be in good enough condition to use the abrasives included with the Drawsharp. But for those which require more aggressive material removal (removing knicks or severely blunted edges) or for those who may not want to grind their knife, Benchcrafted offer a rehab kit with medium and coarse diamond abrasives. The kit includes two sleeves and two each of coarse and medium diamond...
Hock 3 1/2'' Straight-Edge Krenov-Style Plane Assemblies
Dimensions
PI100: High Carbon Krenov-Style Blade and Cap Iron - 1'' x 3 1/2''
PI125: High Carbon Krenov-Style Blade and Cap Iron - 1 1/4'' x 3 1/2''
PI150: High Carbon Krenov-Style Blade and Cap Iron - 1 1/2'' x 3 1/2''
PI175: High Carbon Krenov-Style Blade and Cap Iron - 1 3/4'' x 3 1/2''
PI200: High Carbon Krenov-Style...
Pfeil Chip Carving Knife - Kerb 4
Pfeil Chip Carving Knives come in a variety of shapes, this one is a Kerb 4 also known as Schnitzmesser.
This knife is for whittling and for simple small objects like little animals. The blade is too thick for chip carving but is sturdy enough for rough cutting.
Fine cherry wood handles, shaped to correspond to the use of the knife.
Blade length 50mm
Gransfors Bruk Carpenter's Axe 465
These axes have a straight edge and thin blade with low angle of the bevel face, suited for work in dry wood. The forged inward curve from the heel to the lip of the head allows your hand to grip almost straight above the centre of the edge. This, and the long straight cutting edge, gives rigidity, stability, and control when cutting. Functions like a good heavy knife. The axe poll is ground and...
Veritas Small Tapered Reamer
The Veritas small tapered reamer 5mm to 19mm (3/16" to 3/4") is useful to rustic furniture makers for back-tapering holes for through-tenon wedging.
The bit is 85mm overall length with an 8mm hex shank.
Designed for use in an electric drill, these tools may also be used in a traditional brace.
Lie-Nielsen No.6 Fore Plane
The Lie-Nielsen No.6 Fore Plane is sized midway between a Jack and a Jointer. The No.6 Fore Plane is designed to further true the surface after the Jack has sized it. Its length enables it to skim off high spots as it bridges low spots, delivering a leveled surface ready for the smoothing plane.
18" (457mm) long
2 3/8" (60mm) blade. A2 steel.
Iron body. 7½lbs (3.4kg).
...
Knew Concepts Slip-on Foam Comfort Grip
The foam grips are available only for the Knew Concepts Mk.III, Mk.IV, and titanium hand saws.
The simplest way to reduce the stress on your hands of long hours of sawing is to increase the diameter of the saw’s handle.
This is where the Knew Concepts new Comfort Grips come in: they increase the diameter of the saw’s handle without adding weight, while they also make the handle...
Mortise & Tenon Magazine - Issue 10
Table of Contents:
Will Wheeler - “An Unexpected Gift: Discovering Calm in a Modern Apprenticeship”
Jeff Miller - “An Exercise in Precision & Randomness: Replicating David Pye’s Fluting Engine”
Al Breed - Book Recommendation
Joshua Klein – “Ready Hands: A Letter to My Sons”
John Ruskin - “Savageness”
George Walker –...
Gransfors Bruk Outdoor Axe 425
The Gransfors Bruk Outdoor Axe was inspired and co-developed by Scandinavian survival expert Lars Fält. The handy design with iron sheathed hickory handle is well-balanced, fits into any backpack and expertly handles any outdoor task.
The head weighs 350g (12oz) and has blade length of 65mm (2½"). Overall length 370mm (14½").
Book and protective leather sheath included.
Narex Dowel Plates
These new dowel plates from Narex are made from A2 steel hardened to 61 HRc. The holes are machined with a slight taper on the underside to create a relief on the bottom and sharp edges on top that shears off the corners.
The Metric Dowel Plate makes 4mm to 16mm dowels in mm increments.
The Imperial Dowel plate makes 1/8", 3/16", 1/4", 9/32'', 5/16", 3/8", 7/16'',...
Stanley Catalogue No. 34
More than 100 years ago, Stanley Tools printed handsome catalogues that illustrated the company's woodworking and carpentry tools with detailed illustrations and descriptions of how the tools worked.
Though few of these catalogues survive, they are an invaluable source of information for hand-tool users, offering exploded parts lists of complex tools - such as the No. 45 plane - and advice on...
Carving the Acanthus Leaf
By Mary May
Learning to carve the acanthus leaf is – for carvers – like a pianist learning a Chopin étude, a young oil painter studying the genius of Rembrandt or an aspiring furniture maker learning to cut dovetails by hand.
For carvers, especially those who focus on Classical Western ornament, there comes a time they will inevitably encounter the acanthus leaf, learn it,...
Gyokucho 297 Compact Dozuki 180mm Crosscut
Full Name : Gyokucho Razorsaw Compact Dozuki.
Blade Length : 180mm.
Overall Length : 390mm.
Max Cutting Depth : 45mm.
Teeth Pitch / TPI : 1.0mm / 25.4
Blade Thickness : 0.3mm.
Cutting Width : 0.46mm.
Teeth Pattern : Crosscut.
Gyokucho Product Number : 297.
Weight : 170g.
Replacement Blade : S297
The compact range of saws can do much the same as the full size saws, just...
Pentel Graphgear 1000 Automatic Pencil Set
We were first put onto these little beauties by Jaap Bosma (the taller half of Mappa Tools). Jaap was taking all the credit for uncovering the mechanical pencil, until we stumbled upon a blog from Christopher Schwarz and that they'd been on the market for almost a couple of decades! Anyway, a few years later and the dynamic buying department of CHT sprung into action and finally started to stock...
Lost Art Press - 5 Woodworking Pencils
Traditional school pencils aren't ideal for woodworking. The pencils and lead snap too easily in use. And the eraser is a joke (Lost Art Press have a recommendation below).
After Lost Art Press tested many different combinations of lead (called the “core”) and diameters, this pencil became their shop favourite. It is robust because of its diameter and the fact that it is round....
Ashley Iles 1 1/2'' Shallow Roughing Out Gouge
37mm 1½" handled shallow pole roughing gouge by Ashley Iles.
These tools have carbon steel blades, not HSS that you would find in the turning tools we offer from the likes of Hamlet and Robert Sorby. Carbon steel is preferable on a pole lathe because it will give you a finer edge, but more critically it is easier to sharpen if you are away from the power grid. So this roughing gouge...
Kutzall 1/8'' Sphere Burr - 1/4''
Kutzall burrs are the perfect companions for your rotary carving tools.Made in the USA, Kutzall burrs provide a great combination of material removal and surface quality. Efficient with or against the grain, these burrs have a long wear life.Their outstanding performance on a wide variety of materials to include wood, plastic, rubber, fibreglass and soft stone.NOTE: These burrs should only be used...
Veritas Wood Carver's Vice
A good carver's vice should be adjustable in all three axis. This one has full rotation in two axes and 3" of height adjustment in the third axis. But more important, it has controlled release; when you relieve the clamping pressure, a combination of internal springs and O-rings provides residual resistance so that your work does not suddenly fall or rotate. You can reposition the work and...
Pax Burnisher
Used in conjunction with Cabinet Scrapers to hone their edges after use.
* Walnut handle with Brass Ferrule
* Steel blade
* Puts burr back on Cabinet Scrapers to keep their edges sharp
Connells Leather Apron
Connell apron 36 inch - hand-made in the UK from high-quality moss backed leather that offers good resistance.
British nickel plated rivets are used for extra strength and durability.
Large front pouch enables storage of small tools and accessories.
Fastens with ties at the back which are also long enough to double back and tie at the front if it needs to be tighter.
Guaranteed against...
Flexcut 5'' Flexible Draw Knife KN16
This flexible Flexcut draw knife has 5 inches of workable edge, designed to flex around contours where large amounts of stock need to be removed quickly. The tool can be flexed to accommodate concave or convex surfaces. Cuts can be made that conform more closely to the finished shape, taking less time to sand or scrape.
The curved edge gives a skew-like cutting action for a low resistance cut. This...