Sort By
Per Page
View
Grid
List
Thomas Flinn Pax Veneer Saw 15tpi
The Pax Veneer Saw is made to enable cuts to be started in the centre of a panel of wood and for other inlaying work.
The saw has 15tpi and the two different sides of the blade are made so that one side has a crosscut tooth formation and the other side has a rip tooth formation.
The saw has a Walnut handle and are individually blister packed. Blade length 3".
Auriou Riffler Rasp - Knife / Spoon
These are hand stitched with a comfortable "fat" hexagonal barrel handle which allows you to use the riffler for long periods of time without discomfort or fatigue. Grain 14 is extremely fine and grain 10 is fine.
Veritas Bevel-Up Jointer Plane + PM-V11 Blade
The Veritas low-angle jointer is the largest member of the Veritas bevel-up bench plane family. At 22" x 2.7/8" and weighing 7½lb, it is the answer for jointing edges and flattening large panels.
The bevel-up blade configuration results in a plane that is versatile and straightforward to use. The 12° bed angle, coupled with the 25° blade bevel, creates an effective cutting angle of 37°. Simply...
Open Curve Spoon Knife (Right Handed)
A high quality spoon knife from Wood Tools designed for use with a combined 30 years of spoon carving experience.
The knives are made from an excellent high alloy steel, very hard and tough so they hold an edge for a long time. They come razor sharp and ready to use. The handles are beech and around 7.5″ long, allowing for a great range of grips to be used efficiently.
The open curve spoon...
Auriou Cranked Neck Curved Ironing Rasps
These are the Right Handed versions, to see the Left Handed please CLICK HERE.
These are very useful for working in small areas. The rasp is short and is curved along its length so you can enter your work easily.
The tang is cranked to allow knuckle clearance.
4 sizes and grains based on width:-
10mm wide Grain 12
15mm wide Grain 11
20mm wide Grain 10
25mm wide Grain 09
30mm wide Grain...
Lie-Nielsen No.6 Fore Plane
The Lie-Nielsen No.6 Fore Plane is sized midway between a Jack and a Jointer. The No.6 Fore Plane is designed to further true the surface after the Jack has sized it. Its length enables it to skim off high spots as it bridges low spots, delivering a leveled surface ready for the smoothing plane.
18" (457mm) long
2 3/8" (60mm) blade. A2 steel.
Iron body. 7½lbs (3.4kg).
...
Ashley Iles 1 1/2'' Shallow Roughing Out Gouge
37mm 1½" handled shallow pole roughing gouge by Ashley Iles.
These tools have carbon steel blades, not HSS that you would find in the turning tools we offer from the likes of Hamlet and Robert Sorby. Carbon steel is preferable on a pole lathe because it will give you a finer edge, but more critically it is easier to sharpen if you are away from the power grid. So this roughing gouge...
Barr Framing & Bench Chisels Leather Guards
Designed to fit the Barr framing & bench chisels, these hand-crafted leather guards will help protect your investment. The guard has an ABS plastic backing insert which is sandwiched between saddle grade leather, stitched and riveted.
Will also fit other chisels, but designed with the Barr framing and bench chisels in mind.
Both Veritas Dovetail Saw and Magnetic Guide
Hand-cut dovetails remain the mark of the skilled cabinetmaker and a feature that buyers look for in high-end furniture. Veritas has developed a guide and saw system that lets amateurs achieve professional results. The system also allows the seasoned expert to produce dovetail joints more quickly and with less effort.
The Veritas Magnetic Dovetail 1:8 Guide, clamps in position and holds the saw...
Knob Thorn
Knob Thorn is reddish brown with a very fine, dense texture. Great for turning and fine detail. Ideal for boxes and spindle work.
Tormek Short Tool Jig
This little Tormek woodcarving jig is designed for sharpening short woodcarving tools and the shortest chisels. Suitable for straight shanked tools, such as wood chisels, carving gouges and tools for power carvers.
The jig has two parallel flanges running on both sides of the Universal Support which ensures that the jig at all times – even when rotated – holds the tool square to the...
Veritas Set of 3 Miniature Chisels
This chisel set is the latest addition to the Veritas line of fully functional miniature tools. Made at about 1/3 the scale of our regular bench chisels, each is only about 3-1/4" long overall and weighs less than a third of an ounce. At this scale, the three tools in the set have 3/8", 1/4" and 1/8" wide blades. All permit a delicate touch where fine, controlled cuts are needed.
Their...
Hamlet Standard Skew Chisel
Made from flat rectangular bar heavier than oval section for turning on legs, posts etc.
Pfeil Punches for Wood
Pfeil Punches for Wood are essential tools for woodcarvers looking to add intricate background details to their carvings. Made from high-quality steel, these punches are designed for durability and precision, ensuring each imprint is clean and consistent.
Key Features:
High-Quality Construction: Crafted from durable steel, these punches are built to last and withstand repeated use.
Variety...
Carving the Acanthus Leaf
By Mary May
Learning to carve the acanthus leaf is – for carvers – like a pianist learning a Chopin étude, a young oil painter studying the genius of Rembrandt or an aspiring furniture maker learning to cut dovetails by hand.
For carvers, especially those who focus on Classical Western ornament, there comes a time they will inevitably encounter the acanthus leaf, learn it,...
Ray Iles 1 3/8'' Stanley & Record Block Plane Blade
Designed for the older Record 0230. Stanley 60, 60½, 61 and 103.
Width: 1 3/8''
Length: 4 3/8''
Thick: 3mm (1/8'')
High grade carbon steel hardened to 59 - 61 Rockwell C.
Narex Uni-Scraper
Universal scraper from Narex that can be used for many joinery, carving or restoration tasks.
200mm long. 14mm wide. 0.75mm thick blade.
Gransfors Bruk Small Hatchet 410
The Gränsfors Bruk small hatchet is the baby of them all weighing just 11 ounces and with a 2'' face and 11'' hickory handle. Ideal for splitting kindling.
Book and protective leather sheath included.
Tormek Anti-Corrosion Concentrate (2 Pack)
The Tormek Anti-Corrosion Concentrate makes water non-corrosive. Always use with Tormek diamond wheels. It can also be used with grindstones.
Add 10ml concentrate to 250ml water (~4%). Scale for correct dilution. Mix Anti-Corrosion Concentrate and water before adding to water trough. If you want to save the mix overnight, remember to lower the water trough. Does not contain anti-freeze.
Each...
Henry Taylor Hand Adze Straight Blade
Sheffield made hand forged adzes by Henry Taylor for single handed use.
There is a choice of 3 adzes, this one a 50mm (2') straight edge (like a chisel) or curved end (like a gouge) with either a shallow/mid gouge or a tight gouge (sweep 9).
At the other end to the cutting edge is a square faced hammer poll.
All the adzes have an ash handle of 250mm (about 10') .
The overall head size (from the...
Peacock Oil - Wick - Clear Figure - 250ml
Wick is the the latest Peacock Oil from Skelton Saws, a hard, quick drying and figure enhancing lustrous wood finish.
A unique blend of the world’s finest natural oils, resins and waxes that together produce a hard, bright, breathable, water-repellent, figure enhancing and grain strengthening finish. Peacock Oil Wick, is uniquely formulated to enable a quick build with a fast-drying time.
The...
Set of 3 Clifton Fine Scrapers
A more flexible version of the very popular Clifton scrapers - made in Sheffield, England
Clifton scrapers are made of medium carbon steel with a hardness of RC40/42. This gives them the best balance of edge holding qualities and a flex in the blade for control in using the tool.
Set of 3 - includes 5" x 2.1/2" rectangle, Concave/Convex & Gooseneck.
0.015" carbon steel,...
Clifton No.4 Smoothing Plane
A Clifton No.4 Smoothing Plane.
A quality British made woodworking plane made in Sheffield.
The most popular size of smoother. Despite its size this plane has a very heavy casting and is ideal for getting you the finish you deserve!
Bedrock design frog allows for maximum contact between frog and plane body, and gives you easier, more precise adjustment of the mouth.
Blade is cryogenically...
Pentel Graphgear 1000 Automatic Pencil Set
We were first put onto these little beauties by Jaap Bosma (the taller half of Mappa Tools). Jaap was taking all the credit for uncovering the mechanical pencil, until we stumbled upon a blog from Christopher Schwarz and that they'd been on the market for almost a couple of decades! Anyway, a few years later and the dynamic buying department of CHT sprung into action and finally started to stock...
Ashley Iles 1 1/4'' Deeper Roughing Out Gouge
31mm 1¼" handled deeper pole roughing gouge by Ashley Iles.
These tools have carbon steel blades, not HSS that you would find in the turning tools we offer from the likes of Hamlet and Robert Sorby. Carbon steel is preferable on a pole lathe because it will give you a finer edge, but more critically it is easier to sharpen if you are away from the power grid. So this roughing gouge is...
Temple Tool Co. Ultra Fine Crosscut Dozuki 180mm
Mid-sized Dozuki Japanese pull saw. Ultra-fine Crosscut teeth. Our thinnest and finest crosscut saw. Use for Kumiko, small to medium tenon shoulders, dovetail shoulders, and other fine crosscut needs. For soft and hard woods.
Blade Length 7'' (180mm)
Overall Length16.3'' (415mm)
Crosscut Teeth 30 TPI
Blade Thickness 0.008'' (0.2mm)
Kerf 0.012'' (0.3mm)
In...
Veritas Small Router Plane
The Veritas Small Router Plane is a versatile tool for fine work, particularly on narrow material or in confined areas, this small router plane is invaluable for any task requiring small recesses, grooves or dadoes.
The sole is designed to completely encircle the blade when in the closed-throat position for maximum registration to the workpiece, even when approaching from the side or working...
Spare Blade for Blue Spruce Marking Knife
Blue Spruce .032, Spear Point, Small Marking Blade
Take advantage of the tool-less collet design of the Classic Marking Knife and always work with a fresh cutting edge.
Gyokucho Flush Cutting Saw Single Edge 100mm
Blade Length : 110mm
Overall Length : 270mm
Max Cutting Depth : N/A
Teeth Pitch / TPI : 1.0mm / 25.4
Blade Thickness : 0.3mm
Gyokucho Product Number : 1150
Weight : 40g
A flexible 0.3mm blade with no set allows you to cut flush wihtout damaging your work surface. Useful for trimming dowels, plugs and smaller joints. These are great saws but care must be taken to keep them in top...
Joseph Marples Trial 1 - 6'' Try Square - Rosewood
The Joseph Marples Trial 1 6'' squares have 1/8'' thick machined brass on both the inside and outside faces, thus ensuring accuracy on the inside and outside edges.
They have a chemically blacked spring steel blade, secured to the stock with brass diamond washers and steel rivets. The accuracy of the try squares is well within that required by BS3322.
Kirjes Polishing Cloths
Kirjes Polishing Cloths are an essential accessory for achieving a fine finish on your woodworking projects. Designed to be used with buffing sleeves, these cloths significantly reduce the time and effort required for sanding while delivering exceptional results. Available in different shapes and sizes, including short cylindrical, long cylindrical, dome, and short & fat cylindrical sanders, they...
Left Handed Auriou Cabinet Maker's Rasps
ONLY LEFT HANDED CABINET RASPS AVAILABLE AT THE MOMENT (FEB 2026)
Hamlet 1/16'' Parting Tool
Parting tools are mostly used for cutting through or forming shoulders, and are essential in any workshop.
Veritas Combination Plane
Originally created to replace stacks of hollow and round wooden planes, combination planes are defined by their flexibility. However, they are not complex to use and are often faster to set up than a machine for one-off work.
The Veritas combination plane was designed from the ground up to eliminate problems that made the original Record and Stanley planes often frustrating to use. It is precisely...
Benchcrafted HiVise Mounting Screw
The mounting screw is designed for the HiVise to make it ultimately more portable. The HiVise can be made with either a tail vice cleat or a benchtop batten, but having a mounting screw will allow you to use it in multiple positions around your bench, or anywhere outside the workshop where you are allowed to make a mess!
Anticipating the varied needs of woodworkers Benchcrafted designed the HiVise...
Nakaya Japanese Folding Saw Set
Fujiyama Noko Japanese Folding Saw Set. A Ryoba, Dozuki and a Kataba in one set.
Comfortable rubber handle.
Length when folded 315mm
Teeth protecting and space saving.
Folding Saw Set comes with: Kataba and Ryoba blade with adapter, Dozuki blade with metal back.
Spare blades available and are listed with the individual saws.
Veritas Inlay String Thicknesser
The critical dimension for string inlay material is thickness. If too thick it won’t fit into the groove; too thin, and it will leave an unsightly gap. This Veritas Inlay String Thicknesser scrapes veneer - or any narrow, thin stock up to 2½" wide - to the exact thickness required.
Instead of a sole that travels on top of the material, it has two skates to elevate the blade from the work surface....
Gyokucho Razorsaw Seiun Saku Ryoba Komame (Fine) 240mm
Full Name : Gyokucho Razorsaw Seiun Saku Komame Ryoba.
Blade Length : 240mm.
Overall Length : 575mm Rattan / 555mm TPE.
Max Cutting Depth : N/A.
Teeth Pitch / TPI : Crosscut 1.3mm / 19.5. Rip Cut 3.8-2.4mm / 6.7-10.6.
Blade Thickness : 0.45mm.
Cutting Width : 0.73mm.
Teeth Pattern : Crosscut & Rip Cut.
Gyokucho Product Number : 611 Rattan / 662 TPE.
Weight : 215g Rattan / 260g TPE.
Replacement...
Lie Nielsen Carbide Burnisher
Creating a burr on a scraper requires a hard, highly polished surface.
The Lie Nielsen Carbide Burnishers have a 4" polished solid Carbide shank held in a Cherry handle. A flared Brass bolster protects your fingers while burnishing.
Veritas Bench Hold Down
The Veritas hold-down can clamp workpieces to a bench or anywhere a 3/4" hole can be drilled.
Exceptionally high clamping forces can be obtained with this hold-down for two reasons. First, with the arm free to pivot independently, all levered forces are exerted downward, without any losses due to horizontal slippage from the canting action of the hold-down post. Second, the fine barb-shaped grooves...
Veritas Mortice Chisel Adapter for Veritas Mk.II Narrow-Blade Honing Guide
This Veritas Mortice Chisel Adapter for the Mk.II honing guide expands its blade-holding capacity to allow consistent, accurate honing of mortice chisels. It increases the space between the roller base and the blade carrier to accommodate the thicker blades of mortice chisels, holding blades up to 11/16" thick.
Compatible with the narrow-blade clamping heads, the adapter is configured so...
Pfeil Scorp
The Pfeil scorp is a specialist tool for hollowing out bowls or for spoon making and has a closed ring with cutting edge and handle.
Please note that this Pfeil Scorp is not honed and ready to use.
Blade width 33mm
Pfeil Round Burnisher
The Pfeil Round Burnisher is used for burnishing cabinet scrapes.
9mm diameter polished steel bar, 165mm long with cherry handle.
Vallorbe 'Condor' File Handles
Precision needle file handle. These can be reused time and time again.
AL260 Condor Handle for Needle Files. Recommended for:
5" xx-slim and 6" xx-slim saw files.
AL160 Condor Handle for Needle Files. Recommended for:
4" xx-slim saw files.
Mechanick Exercises
Joseph Moxon’s “Mechanick Exercises or the Doctrine of Handy-Works,” is the first English-language book on woodworking (and other trades) – but it was written by a man who wasn’t a woodworker. Instead, Moxon (1627-1691) was a printer, a maker of mathematical instruments and (for a time) hydrographer to King Charles II.
Oh, and the engravings of woodworking tools in...
Auriou 9'' Straight Drawknife
Auriou's high quality, hand-forged tools are well known to discerning woodworkers, Famous for their hand stitched rasps and rifflers Auriou are using their small team of highly skilled artisans to produce a small range of tools to balance their portfolio of tools. Launched in autumn 2010 this large, straight-blade draw knife is sure to become a favourite in green woodworking circles.
Turned...
Joseph Marples Trial 1 - 12'' Try Square - Rosewood
The Joseph Marples Trial 1 12'' Try Squares have 1/8'' thick machined brass on both the inside and outside faces, thus ensuring accuracy on the inside and outside edges.
They have a chemically blacked spring steel blade, secured to the stock with brass diamond washers and steel rivets. The accuracy of the try squares is well within that required by BS3322.