Sort By
Per Page
View
Grid
List
Brusso Brass Jewellery Box Feet JB-423
The JB-423 decorative box foot, comprised of a sphere with a disC-shaped foot, is pressure-fit and glued into place. It measures 1/2" in diameter and projects 3/8". The mounting dowel is 5/16" in diameter.
Supplied as a set of 4.
Crucible GoDrilla
The Crucible GoDrilla extends the reach of your drill bits (and other tooling) without introducing any run out or wobble. This precision-machined tool (made in Tennessee) allows you to perform many unusual boring and fastening operations with immense ease and accuracy.
DIY store bit extenders are cheap, poorly made and are designed for operations where run out is OK. An oversized hole will be hidden...
Hock 1 1/4'' Carving Knife
This Carving Knife is a general purpose carving knife and the rounded point is very durable. A great knife suitable for beginners.
The length listed is an approximate blade length.
Handles are made from Jatoba with nothing more than an oil finish.
Journeyman Handcrafts Canvas Tool Roll
Keep your carving tools protected and portable with this Journeyman Handcrafts tool roll made from heavy weight 16oz green cotton canvas.
Designed with 16oz cotton canvas, this pouch is made to last and will endure many years of hard use. It’s double stitched with a very strong bonded nylon thread which is water and rot resistant. Finished with veg tan drawstrings for longevity and wooden toggles...
Saburrtooth 1/4'' Flame 3/4'' x 1 1/4''
Head Diameter: 3/4"
Head Length: 1¼"
If grits are not displayed they are no longer available.
Shinwa 90° Try Square - Metric
Stainless steel square.
Measurements on both sides
Angular accuracy 90°: 0.1 mm or less per 100 mm
Outside measurements: 150mm
Inside measurements: 120mm
Base length: 100mm
Thomas Flinn Pax Beech Handled Dovetail & Tenon Saws
The Pax range of saws are made by Thomas Flinn & Co in Sheffield, England. They perform like the 1776 premium range, just don't have all the refinery. So instead of an open Walnut handle, these saws have a closed handle made from steamed Beech with a two-tone gloss finish. They have the same heavy brass back which is folded to give the blade its tension. If you like a heavier saw, then this...
Veritas Miniature Planing Stops
The Veritas miniature planing stop is designed to slip over a pair of miniature surface dogs (sold separately) to provide a reliable registration surface when working on thin or narrow workpieces, allowing materials to be worked without obstruction.
For tasks that involve the application of horizontal force in one direction, such as planing, a single stop can be used with no additional clamping....
Arbortech Contour Sander
The Arbortech Contour Sander is solidly made, ingeniously designed and precision engineered. It uses an innovative new design resulting in a true random orbit action that is only evident when the disc is applied to the work. It gives an excellent finish free of sanding marks and won't leave the friction burns that a spinning pad is prone to do.
The sander is designed to fit a 100 or 110mm portable...
Auriou Traditional Stonecarving Chisels with Square Teeth
The Auriou Traditional Stonecarving Chisels with Square Teeth are meticulously crafted for exceptional performance in soft stone and marble carving. Available in a range of sizes from 4mm to 30mm, these chisels are designed to remove material efficiently while providing precise control. The traditional "fat" hexagonal barrel handle ensures comfortable use over extended periods.
Sizes...
Veritas Low Angle Spokeshave
The Veritas Spokeshave uses a basic traditional shape, not of the spokeshaves of the last century, but of the century before.
Until about 1900, the vast majority of spokeshaves were low-angle spokeshaves with wooden bodies. The blades were hand forged with upturned tangs that fitted into holes pierced in the body of the shave. Wedged in position, they were adjusted by tapping the ends of the...
Veritas Miniature Hold-Down
This 1:3 scale miniature version the Veritas hold-down can secure work vertically on small projects, such as when cleaning up dovetails or chopping mortises.
The low-profile 3'' cast steel arm is unobstructed at the clamping end, allowing good access to work from all sides. Simply turn the brass knob to apply the desired amount of clamping force. The 3'' post fits in a 17/64''...
Veritas Small Plough Plane Conversion Kit - Right Hand
For the Veritas Right Handed Plough Plane
Veritas Small Shoulder Plane + PM-V11 Blade
Designed to seat nicely in the hand, the smallest Veritas shoulder plane is easily controlled using a one-handed grip.
The lever cap wraps around the rear of the body, shrouding the blade adjustment mechanism so it does not obstruct the grip while acting as a comfortable rest for the palm.
The through-hole and textured recesses cast into the side of the body provide grip points for fingers.
The...
Pfeil Round Burnisher
The Pfeil Round Burnisher is used for burnishing cabinet scrapes.
9mm diameter polished steel bar, 165mm long with cherry handle.
Crucible Lump Hammer
The Crucible lump hammer has a 2.2lb. hardened steel head and is ideal for assembly, mortising, setting holdfasts and dozens of other chores. Comfortable octagonal hickory handle with a waxed finish.
The late, great furniture maker Alan Peters often said that one of his favourite tools was his “lump hammer,” a British term for what Americans might call an engineer’s hammer or a small sledge....
Flexcut Pocket Knife Roll KN00
This Flexcut tool roll will hold up to 4 Flexcut knives protecting their edges.
Brusso Brass Stop Hinge JB-804
The Brusso JB-804 brass full mortice hinge is engineered with a built-in stop that allows a lid to remain open at 95°. The hinge is surface mounted and can be used when an additional stay is not desired. The hinge measures 1¼" in length.
Length: 1.250" - 1¼" - 32mm
Width: 1.040" - 1" - 26.5mm
Thickness: 0.188" - 3/16" - 5mm
NOTE - All Brusso...
Kutzall 4 1/2'' Shaping Disc - Extreme
Made in the USA, the Kutzall Shaping Wheels provide a great combination of material removal and surface quality. Efficient with or against the grain, these wheels have a long wear life.
Their outstanding performance on a wide variety of materials to include wood, plastic, rubber, fibreglass and soft stone.
NOTE: These wheels should only be used on non-metallic materials.
The Shaping Wheels...
Lie-Nielsen 16'' Tenon Saw with Cherry Handle
A Tenon Saw is a large backsaw used for making deep, accurate cuts in furniture joinery. It should make straight, fast cuts without binding. Based on a classic Henry Disston model from the early 20th century, our Tenon Saws have Cherry handles, Brass fittings, and stout ¾'' x ¼''' milled Brass backs. These saws are solid, well balanced and smooth cutting. Filed rip...
Sunshine Polishing Cloths (pair)
Keep your tools looking new! Safely cleans jewellery, gold, silver, brass, copper, glass, mirrors and most other surfaces, leaving a deep, long-lasting lustre.
Sold in pairs.
Rub surface to be polished with medium pressure. Non-scratching polishing and cleansing action works until cloth is completely darkened.
Do not wash. When it is darkened, discard.
Thor Nylon Retail Hammer
The Thor Nylon Retail Hammer has interchangeable faces and comes fitted with one White and one Soft Grey screw in Face with Wood Handle. Approximate total length is 305mm (12'')
Alternative faces, colour coded to distinguish hardness are also available:
Replacement heads for 31-710R and 31-712R
Faces are designed to wear and to be replaced by hand.
All faces are one piece moulded.
No...
Veritas Shop Marking Knife
The unique handle shape on this marking knife lets you use it comfortably with a pencil grip when fine control is needed, or a pistol grip that allows greater force to be applied for a more visible line.
The removable blade design lets you flip the blade for right-hand or left-hand use, or for flush registration on either side of a reference surface.
The blade, made of PM-V11 tool steel, is 3/32"...
Auriou Riffler Rasp - V Shape / Rectangle
These are hand stitched with a comfortable "fat" hexagonal barrel handle which allows you to use the riffler for long periods of time without discomfort or fatigue. Grain 14 is extremely fine and grain 10 is fine.
Benchcrafted Glide Leg Vice Base Hardware - Cast
The Benchcrafted Glide makes holding your work quick, easy, and pleasurable. It uses a clever combination of components to deliver incredible clamping force with minimal effort.
Traditional leg vices use a sliding ''tommy bar'' to operate the vice. This style of handle offers one distinct advantage: lots of leverage. These guys have engineered the Glide to deliver rock-solid workholding...
Henry Taylor No.7 Allongee Gouge - 2' (50mm)
These tools were created especially for sculptors who work in large sections of timber.
They are beautifully balanced to handle heavy duty cuts as required and are fitted with heavy duty double hooped handles with shock absorbing leather washers.
Veritas Chamfer Guide for Low-Angle Block Plane
You can convert the Veritas Low-Angle Block Plane (05P22.01) and Standard Block Plane (05P22.30) into chamfer planes in seconds with this cunning guide.
Easy to install - you first set the chamfer width on the guide, then install the guide by unscrewing the front knob of the plane, replacing the toe piece with the chamfer guide and tightening the knob again. It is ready to go.
Adjustable for...
Veritas Reeding Blades for Combination Plane
For use with the combination plane only, these PM-V11 steel reeding blades are available in two-, three- and four-reed versions, with 1/8", 3/16" or 1/4" diameter reeds. A 1/16" groove (also known as a quirk) is cut on either side of each reed. Made in Canada.
Crucible Iron Holdfast
The Crucible holdfast. Made from ductile iron in an Illinois family foundry that’s been in business for more than a century. Based on a French design salvaged from a barn. The last holdfast you are likely to need.
Since Roman times, the iron holdfast has been an essential piece of workbench equipment for carpenters, joiners and cabinetmakers. Yet many of us struggle with holdfasts that work...
Flexcut Mini-Detail Knife KN27
The mini-detail knife has Flexcut's smallest 3/4' straight blade. It is made from ultra-thin material so as not to disturb adjacent wood for very delicate cuts.
Veritas Marking/Mortice Gauge Heads
Though designed for use with their Veritas® Wheel Marking Gauges, these gauge heads are a simple retrofit for any marking gauge with a 5/16" diameter shaft.
Made from carbon steel, the 5/8" diameter wheel cutters will scribe at any point in their circumference and slice rather than tear fibers for clean, accurate cuts. The single-bevel cutters are usable in-line for marking parallel lines, or...
African Blackwood
African Blackwood turns superbly and polishes up to a high shine.
African Blackwood is now CITES listed. Read more at https://cites.org
We have chain of custody documentation to show the African Blackwood we currently offer for sale pre-dates listing or is current with the appropriate import documentation.
Benchcrafted Mag-Blok Oak
We've had our eye on these Mag-Bloks by Benchcrafted for years and years, but sadly they'd previously had an agent in the UK. Thankfully, things have changed and we can import the Mag-Bloks alongside their wonderful bench hardware.
The Mag-Bloks are equally fantastic in both the home and the workshop. We use them here in the shop to display bench chisels, and a couple of us have them in...
Lie-Nielsen Tapered Carcass Saw with Cherry Handle
This is the tapered version of the ever popular carcass saw. The taper gives you better control over precise cuts. When you reach the gauge line on the front of your stock, the blade is slightly above the line on the back side, which reduces the risk of sawing past your line.
The tapered saw is very similar to the standard carcass saw in size, but has a thinner plate of .015". It tapers 1/4"...
Lie-Nielsen Tapered Tenon Saw with Cherry Handle
Lie-Nielsen have redesigned their three most popular back saws to feature a slight tapering of the blade from toe to heel. This taper gives you better control over precise cuts. When you reach the gauge line on the front of your stock, the blade is slightly above the line on the back side, which reduces the risk of sawing past your line. In addition, the taper introduces an angled approach to your...
Making Things Work:
Tales From a Cabinetmaker's Life
Tales From a Cabinetmaker's Life
By Nancy R. Hiller
Furniture making, once a basic way to earn a living through an arrangement between makers and clients, has been discovered, like a rosy-cheeked girl plucked from a dairy farm in Devon and made over into a London model
For many of us, making furniture and cabinetry is still a way to earn a living, however marginal. We may do what we love every day, to paraphrase the marketing...
Nakaya Golden Series - 4 Saw Set
Set of 4 Golden Series Japanese Saws in a traditional heavy linen roll; Ryoba Gold 240, Kataba Gold 240, Dozuki 210 & 240.
Ryoba Gold 240mm
240mm long, 0.5mm thick blade.
Set (Kerf width) 0.75mm.
Tooth spacing / teeth per inch cross-cut: 1.6mm or 15.8TPI (teeth per inch).
Tooth spacing / teeth per inch rip-cut: graduated from 2.7mm (9.4TPI) to 3.9mm (6.5TPI).
Kataba Gold 240
240mm long,...
Pfeil Lino & Block Cutting Tools - Set of 12
Pfeil Lino & Block Cutter Tools - Sets
Veritas 14° Dovetail Saddle Marker (1:
4)
4)
This new 14° marker is designed to approximate a 1:4 ratio, for those who prefer this angle when working in thinner stock, as it not only provides stronger material interlock than traditional ratio angles but produces a slightly exaggerated dovetail joint that many find attractive.
The long legs ensure accurate registration. Also, much like the Veritas saddle square they are based on, they allow...
Benchcrafted HiVise + Mounting Screw
Taking cues from early French prototypes (commonly referred to as an "etau(x)" which is simply the French word for vice) Benchcrafted have gone a few steps further and made improvements and refinements over the historical versions. The body of the vice is designed to be much stronger, yet more compact with its inset arms and single clamping screw for attaching the vise to a workbench or table. The...
Robert Sorby Fingernail Profile Bowl Gouges (Deep Flute)
The profile of this Robert Sorby Fingernail Profile Bowl Gouge increases the flexibility allowing a woodturner to perform "pull cuts" without catching the lathe bed. The greater cutting tip area allows for both delicate shearing cuts and for heavy profiling cuts.
Pfeil - 25 Piece Carving Set
This large fully forged Pfeil 25 piece carving set is for challenging carving projects and contains the roll case, 80mm wooden mallet, 2 genuine Arkansas stones, honing oil, carving knife and 20 full size carving tools.
The tools included are:1/16, 1s/16, 2/20, 3/3, 3/12, 3/25, 5/35, 7/20, 8/7, 8/18, 8/25, 9/7, 8a/18, 9/15, 7L/25, 11/2, 11/10, 15/3, 12/10 and 14/8.
This in plain english means
16mm...
.png "Last Ones!")
Henry Taylor No.9 Fishtail Gouges
This range is being discontinued by the supplier, only available while we have stock.
From the "Professional" range of Henry Taylor carving tools. These fishtail gouges have a 4¾" (120mm) blade with a ground inner surface and a charcoal black non-reflective finish on the outer surface. Fitted with an octagonal beech handle and brass ferrules.
A copy of the Henry Taylor sizing...
Blades for the Veritas Low Angle Smoothing Plane
Veritas 2" Blade in PM-V11 to fit the Veritas Low-Angle Smoothing Plane
Lie-Nielsen Honing Guide 18° Skewed Jaw Pair, Right Hand
The Lie-Nielsen 18° Skewed Jaw Pairs fit the Lie-Nielsen No. 140 Skew Block Plane (left or right hand).
The blade for the right hand No. 140 fits the right skewed jaws.
Pfeil Scorp
The Pfeil scorp is a specialist tool for hollowing out bowls or for spoon making and has a closed ring with cutting edge and handle.
Please note that this Pfeil Scorp is not honed and ready to use.
Blade width 33mm
Clifton 500 10'' Convex Spokeshave
Clifton Spokeshaves are made from virtually unbreakable spheridal graphite/malleable iron; the surfaces are finished and polished to give maximum comfort in the hand; the weight and balance permits the Spokeshave to sit firmly on the wood so that only a stroking action is required to make them cut. The firm seating and fine adjustment allow the woodworker to make delicate nuances in the weight of cut.
Available...