Sort By
Per Page
View
Grid
List
Henry Taylor Woodcarving Punch - Cross 1
Woodcarvers Punches from Henry Taylor which are made here in the UK. They are approximately 75mm (3'') in length and approximately 5mm wide.
Rob Cosman's Marking Gauge Cutters with Rods
What Rob says
Its very convenient to switch out marking gauge cutter sizes by just removing the rod with cutter attached and replacing it with a different size cutter attached to a rod. Therefore, we offer our replacement cutters with rods. These rods are designed to work with the Rob Cosman marking gauge. They should fit any marking gauge that accepts a 5/16 inch (7.94mm) diameter rod, but we...
Crown Tools Dovetail Cutting Tool
In 2001 Stiles and Bates ground some of their 1/2'' scrapers to this profile for a course they were running.
Crown Tools followed suit so you lovely people can also benefit from S&B's innovation.
So this is not a new idea but from what Dave Bates has shared with us, this tool is more useful than other dovetail tools as it will cut both internal and external dovetails on bowls...
Straight Cutter for Gifkins H Series
The TGHS 12 1/4' is the H10 straight cutter and mate to the dovetail cutter. The H10 dovetail cutter and the H10 straight cutter are designed specifically for the H10 Template.
Note: All Gifkins Dovetail cutters are designed for use in a table mounted router, and should not be used in a hand held router.
Henry Taylor Woodcarving Punch - Flower 2
Woodcarvers Punches from Henry Taylor which are made here in the UK. They are approximately 75mm (3'') in length and approximately 5mm wide.
Straight Cutter for Gifkins F15 Series
F15 Finger joint cutter, TGF15 15mm, with a red adjusting sleeve, is designed specifically for use with the F15 Template .
Note: All Gifkins Dovetail cutters are designed for use in a table mounted router, and should not be used in a hand held router.
.png "Last Ones!")
Saburrtooth 6mm Dove Tail - 3/4'' x 1''
15% discount from price shown.
Woodpeckers Edge Rule 900mm
Woodpeckers Woodworking Edge Rule - 900mm. Includes Edge Rule Stop.
Measuring the narrow edge of stock with typical rules is a little awkward. Getting the rule parallel to the stock and leaving yourself room to make a tick mark can become quite a juggling act. Working on the face of a piece is usually a little easier, but you can still struggle to jeep the rule parallel to your work. The Woodpeckers...
Henry Taylor Woodcarving Punch - Tree
Woodcarvers Punches from Henry Taylor which are made here in the UK. They are approximately 75mm (3'') in length and approximately 5mm wide.
Spare Blade for Lie-Nielsen Model Maker's Block Plane
Keep your Lie-Nielsen Model Maker's Block Plane in top condition with this premium replacement blade. Specifically designed for the No. 100 Model Maker's Block Plane, this blade ensures your tool maintains its precision cutting performance.
Key Features:
High-Quality Steel: Made from A2 cryogenically treated tool steel, this blade is engineered for superior edge retention and durability.
Optimized...
Foula View - Greetings Card
Foula View is an image of one of Fiona Kingdon's creations which has been printed on 300gsm card and blank inside for your own greeting.
15cm x 15cm
Crown Tools Revolution Bowl Gouge
Bowl Gouges to use with the Crown Tools Revolution Hollowing System are available in two sizes:
3/8'' (10mm) and 1/2'' (13mm)
Henry Taylor Woodcarving Punch - Arrow Cross
Woodcarvers Punches from Henry Taylor which are made here in the UK. They are approximately 75mm (3'') in length and approximately 5mm wide.
Silky Zubat Saw - Replacement Blades
A curved saw that is a favourite with arborists and other professionals. Large teeth, 7.5 teeth per 30mm
300mm Blade Length or 330mm Blade Length.
Curved Blade Pruning Saw
The Zubat, a heavy duty curved blade saw is the best professional pruning saw available in Britain today. Mono-construction with a moulded rubber handle. Specially designed sheath for the curved blade with a detachable belt...
Flexcut Detail Skew Knife KN32
This Flexcut knife is excellent for fine eye detail and feathers when decoy carving.
14.3mm (9/16') straight blade.
The extended shank offers a deeper reach for the blade.
Rob Cosman's VCI Saw Case:
XXL Size
XXL Size
What Rob says
Protect your premium handsaws from damage and corrosion during storage or transportation with our custom made VCI (Vapor Corrosion Inhibitor) saw cases.
Our XXL sized saw cases are specifically designed for our regular handled Rob Cosman full sized Handsaws, but this case will accommodate similar sized handsaws as long as the maximum saw dimensions are not exceeded (see product...
Flexcut Hooked Push Knife KN33
This Flexcut knife is an excellent choice for making concave, convex, and shaving cuts.
Also designed for cleaning stop cuts.
Saburrtooth 6mm Rotosaw - 2'' x 1/4''
15% discount from price shown.
Gyokucho Folding Saw 200mm + Spare Blade
The Gyokucho Folding Saw 200mm with a spare blade.
![3 Henry Taylor Fishtail Carving Gouges [New, Clearance, SOLD]](/images/products/small/4594_12582.jpg "3 Henry Taylor Fishtail Carving Gouges [New, Clearance, SOLD]")
Woodpeckers T-Square 600mm
Woodpeckers T-Square Metric 600mm with Rack-It
Striking lines parallel with the edge of your stock is made easy with the Woodpeckers Precision T-Square. The beam has a lip that rests on the top surface of your stock, preventing the tool from rolling like many T-Squares. Precision machined scribing guides are spaced every milimetre down the length of the blade. This allows you tro drop the point...
Saburrtooth 6mm Taper - 1/2' x 1' - (Smooth End)
15% discount from price shown.
Woodpeckers Precision Woodworking Square 300mm x 200mm
Woodpeckers 1281 Precision Square with Rack-It 300mm x 200mm.
The core of the 1281 is a precisely machined square milled from cast and ground tool plate......the most stable aluminium in the world. The stability of the material and the methods Woodpeckers use to machine the core mean they all hold the tolerance to +/-.0085°. To this highly accurate core they add cheeks to make the base thicker....
Crown Tools Revolution Spindle Gouge
Spindle Gouges to use with the Crown Tools Revolution Hollowing System are available in two sizes:
3/8'' (10mm) and 1/2'' (13mm)
Henry Taylor Woodcarving Punch - Snowflake
Woodcarvers Punches from Henry Taylor which are made here in the UK. They are approximately 75mm (3'') in length and approximately 5mm wide.
Tormek T8-00 Storage Tray
The Tormek T8-00 Storage Tray stores all the accessories included with the Tormek T-8. The storage tray has an improved design and is customized to fit in the Tormek Case TC-800 and the Sharpening Station TS-740.
The storage tray is made of EPP, a permanent construction material that is durable and ready for many years of holding jigs in their places.
Designed to hold:
WM-200 AngleMaster
HB-10...
![5 French Walnut Handles (with Tapered Brass Ferrules) [Clearance, SOLD]](/images/products/small/3970_10128.jpg "5 French Walnut Handles (with Tapered Brass Ferrules) [Clearance, SOLD]")
![5 French Walnut Handles (with Tapered Brass Ferrules) [Clearance, SOLD]](/images/products/small/3970_10129.jpg "5 French Walnut Handles (with Tapered Brass Ferrules) [Clearance, SOLD]")
5 French Walnut Handles (with Tapered Brass Ferrules) [Clearance, SOLD]
Attractive French Walnut handles for chisels, rasps etc
5" overall (125mm) with 3/4" diameter ferrule, rounded profile with waist.
The handles are pre-drilled with a 4mm diameter hole about 12mm deep.
Clear lacquer finish.
New old stock.
Barr Hand Adze
The Barr Hand Adze is the best choice for roughing out your bowls and chair seats. Designed for maximum control the 2¼" cutting edge is just enough for the task at hand. Not too light, not too heavy it is the perfect addition to your workshop!
2¼" cutting edge, head length 8", total weight 2lbs, handle length 15"
Build your own Gyokucho Cast Saw Bundle
Select 1 of the 6 Gyokucho CAST folding saws (supplied with blade) and add at least one more blade to create your own bundle. You can then add one or two more blades if you wish. The minimum bundle is your chosen saw (with its designated blade) and one additional blade of your choosing. The maximum bundle would be your chosen saw (with its designated blade) plus 3 additional saws of your choosing.
Gyokucho Blue Hard Ryoba 210mm
Full Name : Gyokucho Razorsaw Blue Hard Ryoba.
Blade Length : 210mm.
Overall Length : 530mm Rattan / 510mm TPE.
Max Cutting Depth : N/A.
Teeth Pitch / TPI : Crosscut 1.5mm / 16.6. Rip Cut 3.7-2.5mm / 6.7-10.
Blade Thickness : 0.45mm.
Cutting Width : 0.72mm.
Teeth Pattern : Crosscut & Rip Cut.
Gyokucho Product Number : 649 Rattan / 665 TPE.
Weight : 207g Rattan / 251g TPE.
Replacement...
Hamlet Round Side Cutting Scraper
These Hamlet scrapers are used to finish the insides and bottoms of objects as they are able to cut where conventional tools cannot reach.
This 3/4'' Round Side Cutting Scraper has a 10'' handle.
Henry Taylor Tipped Hollowing Tool - Bent
This versatile hollowing tool from Henry Taylor gives the option of being used as a scraper or hollowing tool thanks to the tip design, which can be rotated to give the most suitable angle of presentation to the work.
Handle length is 11 1/2''
Hewing Wooden Bowls with Peter Follansbee
An exciting form of green woodworking, these carved wooden bowls stem from the same Swedish tradition as Peter's carved spoons. Learn to split blanks from a log and hew bowls using hatchets, adzes, and carving gouges. From log selection to grain orientation, tool use, and decorative carving, this video covers all you need to get started in this enticing craft.
!!!!Disc 1 (1:39)!!!!
1. Introduction...
Replacement Blade for Clifton Low Angle Block Plane
1 5/8'' blade to fit the Clifton low angle block plane.
The Clifton blades are made from O1 steel that has been cryogenically treated to give a hardness of 60 to 62 Rockwell C.
Made in Sheffield, UK
Replacement Blade for Nakaya Kataba Universal Meiko Gold Saw
Replacement blade for the Kataba Meiko Gold Saw.
Kataba Meiko Gold 250 - 250mm blade - 0.5mm thick WKG250M - This is a very clever saw combining x-cut and rip teeth on one edge of a 0.5mm thick blade.
Rotur Standard Duty Rotating Centre
The Rotur Standard Duty Rotating Centre is a reliable, general-purpose tool designed for woodturners. It features a 31mm diameter head with a 60-degree point, ensuring precise and stable support during woodturning. The rotating center is equipped with twin deep groove ball races, which enhance smooth operation and durability. Available in 1 MT and 2 MT sizes, it is suitable for various lathe setups.
Saburrtooth 1/4'' Cylinder - 1'' x 1'' - (Smooth End)
Head Diameter: 1"
Head Length: 1"
Saburrtooth 1/4'' Cylinder - 3/8'' x 3/4''
Head Diameter: 3/8"
Head Length: 3/4"
Saburrtooth 1/8'' Rotosaw - 3/8'' x 3/16''
Head Diameter: 3/8"
Head Length: 3/16"
Spare Blade for Lie-Nielsen 95 Edge Plane
Replacement blade for the Lie-Nielsen No. 95 Edge Planes. Comes with a 25° flat ground bevel.
1.105" wide x .125" thick
A2 cryogenically treated Tool Steel
Tormek Scissors Jig - New
Why SC-60 Scissors Jig?
Simple 60° angle quick setting to get precise angles instantly.
Enhanced compatibility with the WM-200 AngleMaster to easily set any angle you might want.
Designed for ultra-low friction and minimised vibration.
Customized clamping for more secured sharpening.
Compatible with the Tormek T-2 Pro Kitchen Knife Sharpener, Tormek T-4, Tormek T-8 and older models.
Simple...
Flexcut 1.5mm Mixed Profile Micro Tool Set MT910
These Micro Tools can handle the extra-fine details often encountered in woodcarving.
This set features six 1.5mm mixed profile micro tools: MT11 Chisel, MT15 Skew, MT19 Sweep, MT27 Deep U, MT31 45 deg. V, MT39 90 deg. V.
Flexcut Detailing Power Gouge Set RG310
These Flexcut Detailing Power Gouges are tools for smaller carving and detail.
Can be used by hand with the RG102 Handle Adaptor.
Power Gouges included:
RG305 #3 x 3/8''
RG306 #5 x 5/16''
RG309 #11 x 1/8''
RG307 70 deg. x 1/4''
Inlay Slicing Gauge
The Latta Slicing Gauge by Red Rose Reproductions
This tool is used to slice veneer into thin strips to form pieces of stringing. It works much like a marking gauge, and can, in fact, be used for that purpose just as well. This is the only tool that is not ambidextrous, so it is available in both right-hand and left-hand versions to suit the user’s preference.
Hard Maple body with an oil...
Kirjes Basic Sanding System
The Kirjes Basic 2 Drum Sanding Kit (KJ40R140) plus the motor and shaft to provide a complete basic sanding system.
Includes KJ140R and KJ140 Drums.
![Record No.8 Jointer Plane [Pre-owned]](/images/products/small/4687_12808.jpg "Record No.8 Jointer Plane [Pre-owned]")
![Record No.8 Jointer Plane [Pre-owned]](/images/products/small/4687_12807.jpg "Record No.8 Jointer Plane [Pre-owned]")
Record No.8 Jointer Plane [Pre-owned]
A beast of a plane!
Robert Sorby Patriot Chuck
No insert or exert included.
Please select your insert from the list below, or visit here