Sort By
Per Page
View
Grid
List
Lie-Nielsen No.62 Low Angle Jack Plane
The Lie-Nielsen No.62 Low Angle Jack Plane. What is not to like? You take the most popular and useful jack plane and bed it at a low angle (12°). This makes the most versatile group of planes even more versatile.
Comes with a 2" (50mm) wide A2 steel blade which is .175" (4.5mm) thick. From the box it has a 25° bevel, but it is worth sticking a secondary bevel of 5° on it if...
Lie-Nielsen Tongue & Groove Plane - 1/2''
The Lie-Nielsen Tongue & Groove Plane (1/2") cuts a groove with one side of the cutter exposed. Swing the fence to expose both sides to cut the tongue. The slot in the one-piece blade registers on the milled body casting, to ensure squareness and equal depth of cut on both sides. Since this is a heavy stock removal tool no depth adjuster is needed.
Made to centre on 1/2" stock, tongue...
Lie-Nielsen Tongue & Groove Plane - 3/4''
The Lie-Nielsen Tongue & Groove plane cuts a groove with one side of the cutter exposed. Swing the fence to expose both sides to cut the tongue. The slot in the one piece blade registers on the milled body casting, to ensure squareness and equal depth of cut on both sides. Since this is a heavy stock removal tool no depth adjuster is needed.
Comes with a 3/16'' (4.8mm) thick A2 steel...
Make a Chair from a Tree:
Third Edition
Third Edition
By Jennie Alexander
In 2014, Jennie Alexander somewhat reluctantly agreed to a third edition of her 1978 seminal book on green woodworking, “Make a Chair From a Tree” – a book that launched the careers of thousands of woodworkers and helped ignite a green woodworking movement in this country.
Her reluctance wasn’t due to a lack of passion for the book’s subject –...
MoraKniv 120 Sloyd Woodcarving Knife
The Mora 120 Sloyd woodcarving knife is the shorter of the two we carry. The thin (2.8mm thick by 60mm long) blade is made from carbon steel which is easier to sharpen, and will ultimately give you a better edge over the laminated blades. Comes sharp, ready to go to work. The handle is made from oiled birch which is barrell shaped to give good grip. The tang runs the full length of the handle which...
MoraKniv 220 Push Knife
Whilst this looks like a traditional drawknife, this is actually sold as a wood splitting knife. The idea being that you take your larger chunks of wood and split them into smaller pieces of kindling that are easier to light.
It is double bevelled (has a bevel either side like a kitchen knife), whereas drawknives are single bevelled. However you can still use this for other purposes than just splitting...
Muller French-Style Sculptors Adze
Again, these adzes are from Leonhard Muller's Carpenter's Hatchets range but they are based on the traditional French design where the head gradually flares from the poll. 3 sweep widths to chose from and all come with straight hickory handles.
Straight 450mm hickory handles (about 18")
Choice of 65mm, 60mm or 56mm wide medium sweep cutting edge.
Narex Dowel Plates
These new dowel plates from Narex are made from A2 steel hardened to 61 HRc. The holes are machined with a slight taper on the underside to create a relief on the bottom and sharp edges on top that shears off the corners.
The Metric Dowel Plate makes 4mm to 16mm dowels in mm increments.
The Imperial Dowel plate makes 1/8", 3/16", 1/4", 9/32'', 5/16", 3/8", 7/16'',...
Narex Marking Knives
The Narex marking knife is an essential tool for creating marks on wood when laying out precision joinery or transferring measurements. The flat handle profile prevents the knife from rolling off the bench.
With the addition of laser cut finger indents which are useful for applying pressure closer to the tip.
Available in three thicknesses; 2.5mm, 1.2mm, & 0.75mm
Handle: Polished Rosewood...
Narex Mortice Chisels - Set of 4
Robust mortice chisels for chopping out joints and cutting mortices. Sides taper in height and length from tip to shoulder for sidewall clearance. Bulky handle made from hornbeam which is strong enough to withstand heavy blows with a mallet.
Overall length 304mm.
Available as a boxed set of 4 (3mm, 6mm, 10mm and 12mm).
Narex Richter Bevel Edge Chisels
Until recently we stocked the Narex 8116 range of bevel edge chisels which were popular amongst students and people starting out in woodworking. Most importantly the steel in the 8116 range was very good but in our opinion the balance and feel would sometimes let them down. I'm glad to say that this new premium range 8150 from Narex is a massive improvement upon the old chisels. Yes they are not...
Narex Richter Mortice Chisels
These are the premium range of mortice chisels from Narex which have earnt the name ''Richter'', who was the founder of Narex company in the Czech Republic.
Sides are slightly relieved to reduce sidewall friction and to allow minor adjustments.
CR-V cryogenically treated steel to 62HRc .
Ash handles with a stainless steel hoop and ferrule.
149mm blade length. 284mm overall...
Narex Spoon Bent Gouge
A Narex gouge specifically designed for spoon making. The carving tool is spoon bent which makes it easier to hollow a recess. It also has a comfortable, longer than normal (to allow 2 hands for control) octagonal barrell shaped handle made from stained beech.
Narex have used a chrome-silicon alloy steel which is heat treated to 59HRc (which basically means it will take a good edge). Comes sharpened...
Narex Uni-Scraper
Universal scraper from Narex that can be used for many joinery, carving or restoration tasks.
200mm long. 14mm wide. 0.75mm thick blade.
Oscar Rush Large Bowl Adze
A hand forged 50mm diameter hand adze with elliptical sweep profile to the cutting edge.
The head weight is approximately 600g with a 230mm - 235mm long (just over 9''), hand carved, faceted, kiln dried ash handle.
The leather adze cover is made by Oscar using Italian leather with solid brass rivets (these are much stronger than cap rivets).
This adze has been carefully designed for...
Oscar Rush Medium Carving Axe
A standard weight carving axe retaining a relatively compact design but with a broader curved edge for slicy cuts.
This carving axe has a 120mm - 125mm (5'') edge - SYMMETRICAL grind only for this axe (also known as double grind).
The head weight is approximately 625g. If striking the poll, do so with a wooden mallet (not a steel hammer)
The handle - hand carved 300mm - 320mm long...
Oscar Rush Side Axe - Left Grind
A hand forged, 130mm - 135mm (5 1/4'') edge side axe. LEFT grind.
The head weight is approximately 775g.
Handle - 320mm long (just over 1'') hand carved, faceted, kiln dried ash handle.
The leather cover is made by Oscar using Italian leather with solid brass rivets (these are much stronger than cap rivets).
This axe has been carefully designed as an all rounder rather...
Oscar Rush Side Axe - Right Grind
A hand forged, 130mm -135mm (5 1/4'') edge side axe. RIGHT grind.
The head weight is approximately 775g
Handle - 320mm long (just over 12'') hand carved, faceted, kiln dried ash handle.
The leather cover is made by Oscar using Italian leather with solid brass rivets (these are much stronger than cap rivets).
The axe is belt sharpened (2000 grit) and then polished on a wheel...
Oscar Rush Small Bowl Adze
A hand forged 30mm diameter hand adze with a compound sweep profile to the cutting edge (more of a U profile).
The head weight is approximately 450g with a 210mm - 215mm long (just over 8'') hand carved, faceted, kiln dried ash handle.
The leather adze cover is made by Oscar using Italian leather with solid brass rivets (these are much stronger than cap rivets).
This adze has been...
Oscar Rush Small Carving Axe
A small carving axe for all sizes of carving.
This stout hand forged carving axe has a 95mm - 100mm (4'') edge - SYMMETRICAL grind (also known as double grind).
The head weight is approximately 475 - 500g.
If striking the poll, do so with a wooden mallet (not a steel hammer).
The handle is hand carved by Oscar, 275mm - 285mm long (just over 11''), faceted, kiln dried ash...
Pfeil - 25 Piece Carving Set
This large fully forged Pfeil 25 piece carving set is for challenging carving projects and contains the roll case, 80mm wooden mallet, 2 genuine Arkansas stones, honing oil, carving knife and 20 full size carving tools.
The tools included are:1/16, 1s/16, 2/20, 3/3, 3/12, 3/25, 5/35, 7/20, 8/7, 8/18, 8/25, 9/7, 8a/18, 9/15, 7L/25, 11/2, 11/10, 15/3, 12/10 and 14/8.
This in plain english means
16mm...
Pfeil - 8 Piece Carving Set
This Pfeil 8 piece carving set is a starter set containing 7 full size fully forged tools and one chip carving tool. It is supplied in a rugged canvas roll case and the tools are honed and sharpened ready for use.
The tools included are 1/12, 1s/12, 5/12, 4/20, 7/10, 9/4, 12/8 and KERB12.
This in plain English means a 12mm chisel,
12mm skew chisel,
Series 5 12mm gouge,
Series 4 20mm gouge,
Series...
Pfeil Abegglen Detail Knives
These Pfeil Abegglen detail knives have two cutting edges. One side with round cutting edge and the other with a hollow cutting edge. As a result it is possible to make deep cuts but also to carve letters and ornamental work. A universal knife with many uses.
Small hexagonal oiled acacia wood handle.
Large: Blade Length 130mm, Cutting Edge 33mm.
Medium: Blade Length 125mm, Cutting Edge 27mm.
Small:...
Pfeil Canard Knife
Pfeil Canard Knives are for very fine chip carving. They have plum handles and the blade has a straight cutting edge which is ground thin.
Large: The blade length is 45mm.
Small: The blade length is 30mm.
Pfeil Chip Carving Knife - Kerb 1
Pfeil Chip Carving Knives come in a variety of shapes, this one is a Kerb 1 also known as Rosenmesser.
A simple knife for chip carving with a straight blade. You can use it to carve patterns (geometric or simple flowers) as well as whittling.
Fine cherry wood handles, shaped to correspond to the use of the knife.
Blade length 50mm
Pfeil Chip Carving Knife - Kerb 12
Pfeil Chip Carving Knives come in a variety of shapes, this one is a Kerb 12 also known as Fuchmesser.
The most popular Pfeil knife for one-handed carving on small objects where the small piece of wood is held in one hand and the knife is used with the other hand. Compared to the Kerb 1 it has a curved blade which is not suitable for chip carving but which runs easily through the wood for rougher...
Pfeil Chip Carving Knife - Kerb 15
Pfeil Chip Carving Knives come in a variety of shapes, this one is a Kerb 15 also known as Gebogen, 2 Schneiden.
This is a small knife to carve fine details on objects and figures. The curved blade cuts on both sides and has a pointy tip so it can be used in many ways. It is not suitable for chip carving.
Fine cherry wood handles, shaped to correspond to the use of the knife.
Blade length...
Pfeil Chip Carving Knife - Kerb 5
Pfeil Chip Carving Knives come in a variety of shapes, this one is a Kerb 5 also known as Schnitzhaken.
For one-handed carving on small objects, with this specialist shape you can reach deepened areas from above. Not made specifically for chip carving.
Fine cherry wood handles, shaped to correspond to the use of the knife.
Blade length 55mm
Pfeil Chip Carving Knife - Kerb 7
Pfeil Chip Carving Knives come in a variety of shapes, this one is a Kerb 7 also known as Kerbmesser.
This knife is for whittling or chip carving. The blade is curved so it will carve the wood easily but it cannot be used to carve straight lines as you can with the Kerb 1 or Kerb pfeil.
Fine cherry wood handles, shaped to correspond to the use of the knife.
Blade length 40mm
Pfeil Chip Carving Knife - Kerb Pfeil
Pfeil Chip Carving Knives come in a variety of shapes, this one is a Kerb Pfeil also known as Kerbschnittmesser.
The most popular knife made for chip carving (definitely one of our best sellers!). The short pointy blade allows a good grip in the wood.
Fine cherry wood handles, shaped to correspond to the use of the knife.
Blade length 36mm
Pfeil Lino & Block Cutting Tools - Sets of 6
Pfeil Lino & Block Cutter Tools - Sets
Pfeil Polishing Paste, Green
Pfeil Polishing Paste is a fine abrasive paste for polishing honed bevels. Ideal for use with a powered strop, the paste features a cooling property, to avoid heating of the blade. The paste can be used with a cloth.
Weight 900g
Pfeil Scorp Round
The Pfeil scorp round is a tool for hollowing out bowls, or sculpting the seat of chairs etc.
Cherry wood handle.
Forged from K720 steel, blade is 65mm in diameter.
Pfeil Series 22 - Wing Parting Tool
Traditional old English form.
For finishing fingers, toes, lips etc.
Pfeil Two Handed Scorp (Inshave)
This Pfeil two-handed scorp (actually we prefer to call this an Inshave) is ideal for hollowing out large cavities. Special form to cut the seats of chairs.
Cherry wood handles.
Forged from K720 steel. Blade width 140mm
Pfeil Violin Maker's Knives
Pfeil Violin Maker's Knives are easy to resharpen because the special steel is hardened all the way through. These have a double bevel.
Pocket Stones
Used to create the finest edge on precision tools, delicate instruments, and die work. RH Preyda Arkansas files hold their shape while creating the finest, most uniform finish.
Recommended for outdoor enthusiasts in need of a sharp edge on fish hooks, arrows, and hunting knives. The pocket stone's compact size allows it to easily fit in your outerwear pocket, or pack inside your gear. Pocket...
Proxxon Cordless Drill Set
Complete with lithium-ion battery, charger and case.
Ray Iles Rounding Planes
A rounder is also known as rotary plane and is used to create accurate tenons or for rounding spindles for chairs. All of these 6 rounders are made by Ray Iles.
The thick blade is held in place by two washered screws which allows you to adjust or remove the blade for sharpening very easily.
Beech body, lightly linseed oiled.
Having reduced your spindle to a little over the size of the rounder...
Red Rose Reproductions Compass Attachment
Red Rose Reproductions dividers can now be converted to a compass for drawing arcs and circles using the compass attachment. To convert, one of the points is unscrewed from the dividers and replaced with the mounting bracket and screw. The second screw secures a wooden pencil in place. The attachment is universal, and will fit on either the 5" or 7½" divider. Two pencils are included,...
Red Rose Reproductions Dividers
These dividers were designed with a few key objectives in mind. First, they needed to have the ability to be quickly adjusted. Many dividers are fitted with thumb screws used to open and close the arms. This method is fine for some tasks, but falls short when rapid adjustments are needed, such as when using with the sector where adjustments are frequent and over a large range. These are fitted...
Relief Carving in Wood:
A Practical Introduction
A Practical Introduction
By Chris Pye
This is a unique book for woodcarvers. Master woodcarver Chris Pye digs deeply into the process of relief carving by pulling apart a single subject, clearly demonstrating how low and high relief carvings 'work' and how to go about carving them.
Follow this book step by step and you'll learn about the tools and how to handle them properly, and fundamental, transferable carving skills...
Replacement Blade for Tite-Mark Marking Gauge
Replacement Blade for Tite-Mark Standard and Long Marking Gauges.
All Tite-Marks are supplied with an A2 Steel marking blade. Meaning it will take a very keen edge and be tough enough to hold it with minimal maintenance and normal use. Hone the flat side of it occasionally and it will last a long time.
The blades can be damaged however, so having a spare blade around is a good idea.
Precisely...
Robert Sorby Cutter Holder
The Robert Sorby Cutter Holder is a handy little accessory which will accept most of the Robert Sorby cutters.
It avoids skinning fingers when sharpening.
Tip not included.
Robert Sorby Gilt Edge Chisels - Boxwood
Robert Sorby Gilt Edge chisel with boxwood carver handle. Fitted with a tapered brass ferrule for comfort and elegance.
Robert Sorby Heavy Duty Corner Chisel
A heavyweight 1" (25mm) wide bruzz (corner chisel) for cleaning up deep corners of mortises.
Ash Handle
Overall Size:- 380-407mm
Blade Length 239mm
Robert Sorby ProEdge Knife Holder Small
The Robert Sorby ProEdge Small Knife Holder can be used for pocket knives, carving knives and blades up to 8" long.
Please note that you will already need to own a jig to use this (either the PEKJIGS or PEKJIGL).
Robert Sorby ProEdge Long Grind Jig
Helps you to create three different fingernail profiles.
