Sort By
Per Page
View
Grid
List
Henry Taylor Hand Adze Shallow Curved Blade
Sheffield made hand forged adzes by Henry Taylor for single handed use.
There is a choice of 3 adzes, this one a gouge end with a shallow/mid gouge or there is a tight gouge (sweep 9) and a 50mm (2') straight edge (like a chisel).
At the other end to the cutting edge is a square faced hammer poll.
All the adzes have an ash handle of 250mm (about 10') .
The overall head size (from the...
Henry Taylor Hand Adze Straight Blade
Sheffield made hand forged adzes by Henry Taylor for single handed use.
There is a choice of 3 adzes, this one a 50mm (2') straight edge (like a chisel) or curved end (like a gouge) with either a shallow/mid gouge or a tight gouge (sweep 9).
At the other end to the cutting edge is a square faced hammer poll.
All the adzes have an ash handle of 250mm (about 10') .
The overall head size (from the...
Hock 3 1/2'' Straight-Edge Krenov-Style Plane Assemblies
Dimensions
PI100: High Carbon Krenov-Style Blade and Cap Iron - 1'' x 3 1/2''
PI125: High Carbon Krenov-Style Blade and Cap Iron - 1 1/4'' x 3 1/2''
PI150: High Carbon Krenov-Style Blade and Cap Iron - 1 1/2'' x 3 1/2''
PI175: High Carbon Krenov-Style Blade and Cap Iron - 1 3/4'' x 3 1/2''
PI200: High Carbon Krenov-Style...
Hock Burnishers
Hock burnishers are hardened (Rc64) and polished high carbon tool-steel rods that stand up well to constant use on scraper edges. Most others are not hard enough for this demanding application.
Needs to be handled.
Size: 3/8" x 6
Hock High Carbon 5'' Chef's Knife Kit
Ron Hock High Carbon kit to create a Chef's Knife with a 5" blade , 1/8" thick - sold without handles and include 3 steel pins.
General Info on the Hock Tools Knife Kits - The top quality, high carbon tool steel in these blades makes a superior cutting tool in the kitchen. While stainless cutlery can be handy nothing cuts better in the kitchen than high-carbon tool steel. This is...
Hock High Carbon 8'' Chef's Knife Kit
A kit by Ron Hock to create a Chef's Knife with a 8" blade. 1/8" thick - sold without handles and include 3 steel pins.
General Info on the Hock Tools Knife Kits - The top quality, high carbon tool steel in these blades makes a superior cutting tool in the kitchen. While stainless cutlery can be handy nothing cuts better in the kitchen than high-carbon tool steel. This is O1 tool...
Hock Metal Spokeshave Blades
2 .1/8'' Cutting Edge.
Hock Replacement blades for metal spokeshaves (Stanley and Record Type 151).
Perhaps the most dramatic improvement can be realised by accurizing and tuning your Spokeshave. It is a mediocre tool as it comes from the factory, but with a quality blade and a little fussing, it becomes a versatile and sensitive tool capable of doing fine work. Stanley and Record Style...
Hock Replacement Blades for Stanley-Style Scraper Planes
The blades for the Stanley No.12 and No.112 Scraper Planes are 3/32" thick by 2-7/8" wide and 5" long with a 45 degree bevel on the cutting edge. Hardened for a balance of long edge life and burr "rollability".
No.80 replacement blade (also fits the Record 080) measures 1/16" X 2-3/4" X 3" long.
No.81 replacement blade measures 1/16" X 2-1/2"...
Hock Scratch Stock
Ron Hock Scratch Stocks are made from tough, wear-resistant bamboo plywood. Two spring steel blades are included, one of which has a quirk-bead shape cut into it, to get you started using your Scratch Stock with no more than final honing. Other shapes are up to your imagination and are cut into the blades with files and slipstones.
The body measures 3/4" x 1-1/2" x 4-3/4", the blue-tempered...
Journeyman Handcrafts Canvas Tool Roll
Keep your carving tools protected and portable with this Journeyman Handcrafts tool roll made from heavy weight 16oz green cotton canvas.
Designed with 16oz cotton canvas, this pouch is made to last and will endure many years of hard use. It’s double stitched with a very strong bonded nylon thread which is water and rot resistant. Finished with veg tan drawstrings for longevity and wooden toggles...
Journeyman Handcrafts Wool Lined Tool Roll
Keep your carving tools protected and portable with this Journeyman Handcrafts tool roll made from a two colours of 8oz waxed cotton canvas giving a lovely contrast of colour when rolled up. The tool roll is lined with a cream wool to give added protection to your tools.
This tool roll is made to last and will endure many years of hard use. It’s double stitched with a very strong bonded nylon...
Knew Concepts 6 1/2'' Coping Saw
On the Knew Concepts Coping Saw the blade is tensioned by a cam-lever and pulls so taut that the blade "sings" when plucked. Chris Schwarz said "...it's more like sawing with an unbendable wire than a floppy steel hotdog (which is what is typical of most saws)". Make turns that are tighter than ever before.
The solid steel indexing blade-hooks lock in eight 45° positions...
Knew Concepts Mk.IV Heavy Duty Fret Saw with Lever Tension & Swivel Blade Clamps
The Knew Concepts Mk. IV Fret Saws are designed to pull 50-60lbs of tension on their blades, which makes it much stronger, and the blades vibrate less than the standard saws. They are are also thicker and slightly heavier, closer to the weight of a traditional saw, but still lighter. The saw is powder-coated red, with a laser engraved logo and is extremely scratch and damage resistant.
The Cam Lever...
Kutzall 3 Piece Coarse 1/4'' Burr Kit
Kutzall burrs are the perfect companions for your rotary carving tools.
This Kit provides the perfect combo of removal rate and surface quality, along with the versatility you need on your larger projects. With three of the most popular shapes in the dependable ‘Coarse’ coating, this package is as trustworthy as it comes.
Set Includes:
Sphere Burr (S-1)
Coarse (Original)
Head...
Kutzall 3 Piece Fine 1/4'' Burr Kit
Kutzall burrs are the perfect companions for your rotary carving tools.
Made in the USA, Kutzall burrs provide a great combination of material removal and surface quality. Efficient with or against the grain, these burrs have a long wear life.
Their outstanding performance on a wide variety of materials to include wood, plastic, rubber, fibreglass and soft stone.
NOTE: These burrs should only...
Kutzall 3 Piece Very Coarse 1/4'' Burr Kit
Kutzall burrs are the perfect companions for your rotary carving tools.
With three of the most versatile shapes in the open-spaced, ‘Very Coarse’ coating, these Burrs are ready to get to work whenever action calls.
Set Includes:
Sphere Burr (SX-1C)
Very Coarse (Extreme)
Head Dimensions: 1'' x 1''
Flame Burr (FLX-12C)
Very Coarse (Extreme)
Head Dimensions:...
Kutzall 4 1/2'' Shaping Disc - Original
Made in the USA, the Kutzall Shaping Wheels provide a great combination of material removal and surface quality. Efficient with or against the grain, these wheels have a long wear life.
Their outstanding performance on a wide variety of materials to include wood, plastic, rubber, fibreglass and soft stone.
NOTE: These wheels should only be used on non-metallic materials.
The Shaping Wheels...
Kutzall 4 Piece Coarse 1/8'' Burr Kit
Kutzall burrs are the perfect companions for your rotary carving tools.
This Rotary Burr Kit provides the perfect combo of removal rate and surface quality, along with the versatility you need on your larger projects. With 4 of the most popular shapes in the dependable ‘Coarse’ grade, this package is as trustworthy as it comes. Includes extra slot for tool storage.
Set Includes:
Taper...
Leadwood
Leadwood is well suited to turning and carving. Dark brown heartwood with blackish streaks. Hard, heavy and durable. Sandpapers, varnishes and oils well to a high lustrous finish.
Lee Valley 3-in-1 Brass Marking Gauge
This elegant Lee Valley marking gauge is really three tools in one - a wheel gauge, a pin gauge, and a cutting gauge.
The unique swivelling pin/blade chuck takes either a pin or a blade that locks in place (after extension is set) using a set screw in the end of the 4½" gauge stem. The cutting blade can be set for either right or left handed use. The opposite end of the stem is tapped to accept...
Lee Valley Winding Sticks
Winding sticks are not new; woodworkers have been making them for years from scrap wood and using them to check the flatness of material. Placed at opposite ends of a board, they accentuate any twist (wind), making it easier to identify and correct. With the sticks in place, sight across their top edges. If the edges are parallel, the board is not twisted. Reposition and repeat to check the entire...
Lie Nielsen Carbide Burnisher
Creating a burr on a scraper requires a hard, highly polished surface.
The Lie Nielsen Carbide Burnishers have a 4" polished solid Carbide shank held in a Cherry handle. A flared Brass bolster protects your fingers while burnishing.
Lie-Nielsen Bronze Low Angle Block Plane
The Lie-Nielsen small bronze Low Angle Block Planes fit perfectly in the hand and slip easily into the pocket. The 5¼" body holds a 1¼" x 1/8" thick blade. An unobtrusive Stainless Steel adjuster offers blade control of micrometer ease and precision with minimum backlash. The mouth is not adjustable.
The blade in the Low Angle Plane is bedded at 12° for fine cuts...
Lie-Nielsen Corner Chisel 3/8''
Producing square mortises is exacting work. The Corner Chisel, used after the mortise has been roughed out by hand or with a slot mortiser—which produces round edged mortises—helps square corners easily and precisely.
Made from A2 Tool Steel, hardened to RC 60-62 and ground razor sharp. Beveled at 30º. Comes with a Hickory handle. Overall length is approximately 10".
Currently...
Lie-Nielsen Honing Guide Chisel Jaw Pair
The Lie-Nielsen Chisel Jaws fit their 1/8" and 3/16" Bevel Edge Chisels (as well as the 1/4" to 3/4" Bevel Edge Chisels).
Lie-Nielsen Honing Guide Mortice Chisel Jaw Pair
The Lie-Nielsen Mortice Chisel Jaws fit all Lie-Nielsen Mortice Chisels, as well as their 1" Bevel Edge Chisel.
Lie-Nielsen Leather Saw Cases
Protect your Backsaw with this fitted Michigan Leather case. Use it for storage and transportation. Beautifully made in Maine.
Lie-Nielsen Model Maker's Block Plane No.100
This delightful, small low angle tool fits snugly in the palm of your hand. It is a miniature work-horse ideal for all sorts of chamfering and trimming jobs.
Blade is 7/8" wide, .125 thick. At 4 3/8" long and 1 1/4" wide, weighing 8oz, this plane is effortless to use.
Lie-Nielsen Mortice Chisel Roll
7 pocket leather tool roll, Brass fittings. Deeper tool roll accommodates the Lie-Nielsen mortise chisels. Beautifully made in Maine, USA.
Lie-Nielsen Mortice Chisels
Designed with cabinetmaking in mind, these well-balanced Mortise Chisels are ground with parallel sides and are thicker than they are wide to help keep them straight in the cut.
Made of A2 Tool Steel, hardened to Rockwell 60-62, cryogenically treated and double tempered. Hard Maple handles. Overall length is approximately 10.5".
The bevel is ground sharp at 30º, but a higher secondary...
Lie-Nielsen No 101 Violin Maker's Plane
This pocket-sized block plane is the smallest of the Lie-Nielsen hand planes to feature a captive nut blade adjuster for precisely controlled depth of cut.
Loosely based on the Stanley No.101 block plane, the Lie-Nielsen Violin Maker’s Plane features several significant improvements that put it in a class of its own. The body and cap are made from Manganese Bronze for extra weight, durability,...
Lie-Nielsen No.042 Medium Shoulder Plane
A improved version of the now discontinued Record 042. This plane is 3/4" wide and weighs 2.35 lbs. The body is 9¼" long, with a 3/4" x .140" thick blade.
This is an elegant tool for trimming and fitting tenons, dados and rebates.
!!!!
Lie-Nielsen No.100 1/2 Convex Sole Block Plane
This is a sweet little plane from Lie-Nielsen Toolworks.
This curved sole low angle block plane is perfect for all sorts of hollowing jobs, chair seats, mouldings, model making, etc.
The radius across the width of the sole is 3 inches, from end to end the radius is 27 inches. The sole is 3 1/2 inches long and the overall length with the squirrel tail handle is 5 inches.
The 1/8 inch thick...
Lie-Nielsen No.51 Shooting Board Plane - Right Hand
The Lie-Nielsen Shooting Board Plane is a single purpose plane is designed to trim mitres and other end grain cuts on a shooting board. Stanley first made its version in 1909 along with a metal shooting board. Lie-Nielsen had many requests for this tool over the years, so we are pleased they redesigned the Stanley version.
The Lie-Nielsen version utilises a standard 60mm (2.3/8") bench plane...
Lie-Nielsen No.62 Low Angle Jack Plane
The Lie-Nielsen No.62 Low Angle Jack Plane. What is not to like? You take the most popular and useful jack plane and bed it at a low angle (12°). This makes the most versatile group of planes even more versatile.
Comes with a 2" (50mm) wide A2 steel blade which is .175" (4.5mm) thick. From the box it has a 25° bevel, but it is worth sticking a secondary bevel of 5° on it if...
Lie-Nielsen Small Router Plane Open Throat
Loosely based on the Stanley No. 271, these small Router Planes are perfect for shallow mortise and small relief work. The compact design makes it easy to guide along narrow edges and fit into tight spaces.
The Closed Throat design gives more support in front of the blade, making it ideal for working on the edges of boards or cleaning out the end of a stopped groove in a rail or stile.
Lie-Nielsen...
Lie-Nielsen Tapered Tenon Saw with Cherry Handle
Lie-Nielsen have redesigned their three most popular back saws to feature a slight tapering of the blade from toe to heel. This taper gives you better control over precise cuts. When you reach the gauge line on the front of your stock, the blade is slightly above the line on the back side, which reduces the risk of sawing past your line. In addition, the taper introduces an angled approach to your...
Lie-Nielsen Tongue & Groove Plane - 1/2''
The Lie-Nielsen Tongue & Groove Plane (1/2") cuts a groove with one side of the cutter exposed. Swing the fence to expose both sides to cut the tongue. The slot in the one-piece blade registers on the milled body casting, to ensure squareness and equal depth of cut on both sides. Since this is a heavy stock removal tool no depth adjuster is needed.
Made to centre on 1/2" stock, tongue...
Lie-Nielsen Tongue & Groove Plane - 3/4''
The Lie-Nielsen Tongue & Groove plane cuts a groove with one side of the cutter exposed. Swing the fence to expose both sides to cut the tongue. The slot in the one piece blade registers on the milled body casting, to ensure squareness and equal depth of cut on both sides. Since this is a heavy stock removal tool no depth adjuster is needed.
Comes with a 3/16'' (4.8mm) thick A2 steel...
MoraKniv 120 Sloyd Woodcarving Knife
The Mora 120 Sloyd woodcarving knife is the shorter of the two we carry. The thin (2.8mm thick by 60mm long) blade is made from carbon steel which is easier to sharpen, and will ultimately give you a better edge over the laminated blades. Comes sharp, ready to go to work. The handle is made from oiled birch which is barrell shaped to give good grip. The tang runs the full length of the handle which...
MoraKniv 220 Push Knife
Whilst this looks like a traditional drawknife, this is actually sold as a wood splitting knife. The idea being that you take your larger chunks of wood and split them into smaller pieces of kindling that are easier to light.
It is double bevelled (has a bevel either side like a kitchen knife), whereas drawknives are single bevelled. However you can still use this for other purposes than just splitting...
Narex Dowel Plates
These new dowel plates from Narex are made from A2 steel hardened to 61 HRc. The holes are machined with a slight taper on the underside to create a relief on the bottom and sharp edges on top that shears off the corners.
The Metric Dowel Plate makes 4mm to 16mm dowels in mm increments.
The Imperial Dowel plate makes 1/8", 3/16", 1/4", 9/32'', 5/16", 3/8", 7/16'',...
Narex Marking Knives
The Narex marking knife is an essential tool for creating marks on wood when laying out precision joinery or transferring measurements. The flat handle profile prevents the knife from rolling off the bench.
With the addition of laser cut finger indents which are useful for applying pressure closer to the tip.
Available in three thicknesses; 2.5mm, 1.2mm, & 0.75mm
Handle: Polished Rosewood...
Narex Mortice Chisels - Set of 4
Robust mortice chisels for chopping out joints and cutting mortices. Sides taper in height and length from tip to shoulder for sidewall clearance. Bulky handle made from hornbeam which is strong enough to withstand heavy blows with a mallet.
Overall length 304mm.
Available as a boxed set of 4 (3mm, 6mm, 10mm and 12mm).
Narex Richter Mortice Chisels
These are the premium range of mortice chisels from Narex which have earnt the name ''Richter'', who was the founder of Narex company in the Czech Republic.
Sides are slightly relieved to reduce sidewall friction and to allow minor adjustments.
CR-V cryogenically treated steel to 62HRc .
Ash handles with a stainless steel hoop and ferrule.
149mm blade length. 284mm overall...
Narex Spoon Bent Gouge
A Narex gouge specifically designed for spoon making. The carving tool is spoon bent which makes it easier to hollow a recess. It also has a comfortable, longer than normal (to allow 2 hands for control) octagonal barrell shaped handle made from stained beech.
Narex have used a chrome-silicon alloy steel which is heat treated to 59HRc (which basically means it will take a good edge). Comes sharpened...
Narex Uni-Scraper
Universal scraper from Narex that can be used for many joinery, carving or restoration tasks.
200mm long. 14mm wide. 0.75mm thick blade.
Oscar Rush Large Bowl Adze
A hand forged 50mm diameter hand adze with elliptical sweep profile to the cutting edge.
The head weight is approximately 600g with a 230mm - 235mm long (just over 9''), hand carved, faceted, kiln dried ash handle.
The leather adze cover is made by Oscar using Italian leather with solid brass rivets (these are much stronger than cap rivets).
This adze has been carefully designed for...