Sort By
Per Page
View
Grid
List
Veritas Jack Rebate Plane + PM-V11 Blade
This Veritas Jack Rebate plane cuts large-scale rebating down to size. The body is 385mm long and the blade extends the full width (57mm) of the body. It is suitable for very large rebates and fielded or bevelled panels. The long sole and substantial mass help ensure accuracy.
The 4.8mm thick bevel-up blade makes right or left-handed corner cuts cleanly and accurately. Adjustable scoring spurs...
Veritas Japanese Style Awl
These Veritas Japanese style awls have accurately turned conical tips, strong bolsters and comfortable handles. The tip is A2 steel hardened to Rc60-62 for toughness, and can be replaced if damaged.
The bolster, made from stainless steel, transitions smoothly into the taper of the handle to provide a larger hand contact area. The hard maple handles have been torrefied, a heating process that changes...
Veritas Low-Angle Block Plane + PM-V11 Blade
Veritas have made a block plane that uses a ''Norris'' style combined sideways (lateral) and up and down adjustment which gives you greater control when adjusting its impressive 1/8'' thick by 1 5/8'' wide PM-V11.
This plane also overcomes one of the drawbacks of other block planes in having higher side wings (ideal for shooting) with finger grips in each side. The...
Veritas Medium Router Plane
Slightly larger than the Veritas small router plane, this tool has the advantage of using the same blades as our full-size router plane.
For general use, the blade may be positioned inboard with the sole encircling it for maximum registration on the workpiece, even when approaching from the side or working an edge. This allows it to bridge recesses, providing great stability even on narrow stock....
Veritas Medium Shoulder Plane + PM-V11 Blade
The shoulder plane (a specialized rebate plane) is the ultimate tool for trimming a joint to a perfect fit. There is no better plane for trimming the shoulder of a tenon to perfection or for rebating work.
The Veritas® medium shoulder plane is proportioned for versatility; it measures 7" long by 0.700" wide and weighs 2 lb. The ductile cast iron body is accurately machined and ground so that...
Veritas Miniature Low Angle Block Plane
This version of the Veritas low-angle block plane is about a third the size of the original. At just under 2½" long and ¾" wide, it is a useful size for small-scale work or where a larger plane would be difficult to use. The low 12° bed angle combined with the 25° blade bevel gives it a cutting angle of 37°, making it also suitable for end-grain use.
The stainless-steel Norris-style adjuster...
Veritas Miniature Planing Stops
The Veritas miniature planing stop is designed to slip over a pair of miniature surface dogs (sold separately) to provide a reliable registration surface when working on thin or narrow workpieces, allowing materials to be worked without obstruction.
For tasks that involve the application of horizontal force in one direction, such as planing, a single stop can be used with no additional clamping....
Veritas Miniature Router
This 75mm wide router plane not only looks like its full-size counterpart, it works like it too. Comfortable to hold and manoeuvre, it is ideal for hardware installation, fine inlay or intarsia work.
It comes with a 3.2mm wide A2 tool-steel blade (hardened to HRC 60-62), positioned inboard for standard use or outboard for true bullnose work. The carefully machined stainless steel body has a ground...
Veritas Miniature Wonder Dog
This 1:3 scale version of the Veritas Wonder Dog is especially useful for securing small work horizontally. Sized to fit in a 17/64'' dog hole, it has a 1 1/2'' long stainless-steel post with an O-ring for slightly elevated clamping.
At 3/4'' wide and 1/4'' high, the brass head will not mark tools or workpieces. The clamping screw provides approximately 1 1/4''...
Veritas Mk.II Honing Guide
The key to consistent and fast honing is repeatability - and this guide delivers it in spades. Whether you're a sharpening veteran or just starting out, this versatile guide lets you concentrate on sharpening without worrying about controlling blade angle at the same time. This makes your honing reliable, accurate and consistent. Three options let you choose the honing guide that best suits your...
Veritas Mortice Chisel Adapter for Veritas Mk.II Narrow-Blade Honing Guide
This Veritas Mortice Chisel Adapter for the Mk.II honing guide expands its blade-holding capacity to allow consistent, accurate honing of mortice chisels. It increases the space between the roller base and the blade carrier to accommodate the thicker blades of mortice chisels, holding blades up to 11/16" thick.
Compatible with the narrow-blade clamping heads, the adapter is configured so...
Veritas No.80 Style Cabinet Scraper
This cabinet scraper is a very useful and versatile tool. Used in place of a much heavier belt sander, it can clean a dirty workbench top, remove dried glue and smooth a panel or tricky grain table top efficiently, leaving behind a surface free of tear-out, digs or gouges.
Veritas have designed this tool with several improvements over what is usually known as the No.80 cabinet scraper. To allow...
Veritas Plane Screwdriver
A regular screwdriver just doesn't work well on cap iron screws. A narrow blade can mar the cap-screw slot, and there's always the risk that the screwdriver tip will slip out of the slot altogether. Veritas have designed this screwdriver to make it both safe and easy to remove, replace or adjust cap irons.
It has a turned brass collar surrounding the tip to capture the head of a cap iron screw...
Veritas Planing Stop
These low-profile work stops present a broad bearing surface. Particularly useful with thin or narrow workpieces, each 1 1/4" wide anodized aluminum rail projects just 0.22" above the bench top, allowing materials as thin as 1/4" to be worked or planed without obstruction. It also provides a reliable registration surface for materials too narrow to span two adjacent bench dogs.
The...
Veritas Rip Cut Carcass Saw
The saw has a 275mm (11") long by 0.5mm thick high-carbon steel blade filed for rip cutting at 12tpi. The teeth have a rake angle of 10°, an included angle of 60° for fast and accurate cutting along the line of the grain. The depth of cut is 60mm.
The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece...
Veritas Round Spokeshave (with PM-V11 blade)
The Veritas Round Spokeshave has a 3.2mm thick PM-V11 steel blade, which fits perfectly onto the machined blade.
The ductile cast iron body is fitted with hardwood handles, shaped for comfort and control. The toe serves as a thumb rest allowing the user to choke up on the body to attain exceptional control. Twin adjustment wheels quickly and accurately control cut depth and skew and shims let...
Veritas Router Plane
Veritas Router Plane
Veritas Ruler Stop
The Veritas ruler stop increases the usefulness of a metal ruler by providing a solid reference point. It is ideal for setting saw fences, repeat cuts, etc.
To use, slide the stop over the ruler end and tighten it at the desired position. The notched post at the tip of the brass adjustment screw allows even the thinnest rulers to be clamped securely; it will not mar the ruler edge. Repositioning...
Veritas Shooting Board
The 24" long shooting track fits the Veritas shooting plane.
This is a shooting board that doesn’t limit you to one angle, the fence is adjustable to let you shoot up to 60° from square. A spring-loaded button registers in fixed detents at 0°, 18°, 22.5°, 25.7°, 30°, 36°, 45° and 60° to let you quickly set the fence for square angles as well as miter cuts to produce frames with ten,...
Veritas Shooting Board Fence
The Veritas Shooting Board Fence Kit lets you construct a shooting board that doesn’t limit you to one angle – the fence is adjustable to let you easily shoot mitres of various angles. A spring-loaded button registers in fixed detents at 0°, 18°, 22.5°, 25.7°, 30°, 36°, 45° and 60° to let you quickly adjust the fence to shoot square angles as well as mitres for frames with ten, eight,...
Veritas Shooting Board Track
These are straight, durable aluminium tracks for making your own shooting board. They are designed to fit the Veritas Shooting Plane, and any other plane with a running surface between 2-1/32" and 2-1/4" wide; you can adjust the stainless-steel outer rail for a perfect fit. Set screws keep the rail from shifting in use.
The inner rail is 11/64" tall. Low-friction UHMW strips in the...
Veritas Shooting Plane + PM-V11 Blade
The mass of this Veritas Shooting Plane, its long base and low centre of gravity make it both stable and effective. Tipping the scales at just over 3.5kg and just under 400mm long, it is a substantial plane; you will appreciate the authority it provides when shooting.
The body is fully stress-relieved, ductile cast iron, with a sole and running surface machined flat and square to one another;...
Veritas Short Blade Honing Guide
A frequent challenge faced by sharpeners of all skill levels is the safe and accurate honing of small or short blades. Spokeshave, small block plane and palm plane blades are too small for most guides. This short blade honing guide has the flexibility to hold small blades that other honing guides cannot handle.
Blades up to 2 5/8'' wide are easily aligned with the included registration jig...
Veritas Side Rebate Plane
The Veritas Side Rebate Plane is used for cleaning up or trimming sidewalls of rebates, dadoes or grooves to yield a perfect fit with its mate. It has a practical dual-blade configuration, coupled with an ingenious pivoting handle that permits right- or left-hand use to accommodate grain direction.
The thin sole functions much like a skate, allowing use in slots as narrow as 3/16" and to...
Veritas Skew Block Plane + PM-V11 Blade
The Veritas Skew Block Plane is a versatile plane that excels at trimming rebates and planing end grain. Of course, you can also use it as a normal block plane. Its Norris-style adjuster guarantees precise blade setting. Machined and surface ground, the 162 x 44mm body is ductile cast iron. It has a 12° bed angle and a movable toe fully enclosed by the body casting. A Bubinga knob locks the toe...
Veritas Small Bevel-Up Bench Plane + PM-V11 Blade
This Veritas low angle smoother is 225mm long, 59mm wide and weighs only 1.25kg. It is easier to handle than a full size smoother. Think of it lying somewhere between a large block plane and a full size smoother, then you’ll see just how useful this plane can be.
Like a full size version, it is useful for final finishing of surfaces, end-grain work and for shooting mitres. The ductile cast...
Veritas Small Plough Plane
This is Veritas' redesigned small plough plane. While it still excels at cutting grooves, rabbets and tongues, it now has the ability to cut decorative beading (beading blades available soon).
Closest in size to the classic Record #044 plane, the preferred size of the old-style plough planes, it has a 6 5/8'' long fence that registers solidly to the workpiece and is through-drilled...
Veritas Small Router Plane
The Veritas Small Router Plane is a versatile tool for fine work, particularly on narrow material or in confined areas, this small router plane is invaluable for any task requiring small recesses, grooves or dadoes.
The sole is designed to completely encircle the blade when in the closed-throat position for maximum registration to the workpiece, even when approaching from the side or working...
Veritas Small Tapered Reamer
The Veritas small tapered reamer 5mm to 19mm (3/16" to 3/4") is useful to rustic furniture makers for back-tapering holes for through-tenon wedging.
The bit is 85mm overall length with an 8mm hex shank.
Designed for use in an electric drill, these tools may also be used in a traditional brace.
Veritas Standard Marking Gauge
Standard Gauge - pretty much the same construction as the micro adjust but these are slighly shorter at 6" and do not have the micro adjust feature.
Veritas Tapered Snug Plug Cutters
Sometimes when plugging holes, no matter how carefully drilled, the holes finish up slightly oversize for the plug, especially in soft woods. These Veritas cabinet maker's snug plug cutters overcome this by cutting a slightly tapered plug.
The first 3mm of the plug is the diameter stated whilst the remaining length is then flared out at an angle of 3°. Just tap the plug into place until you...
Veritas Tapered Tenon Cutters
Veritas tapered tenon cutters will put tapered tenons on the tips of turnings, dowels or rustic furniture components to fit into tapered holes; for example, legs and spindles on a Windsor chair. Use the cutter like a hand-held pencil sharpener; you either rotate the workpiece while pressing it into the cutter body or you can rotate the tool on the workpiece. Works equally well in soft, green or hard...
Veritas Universal Variable Angle Plane Fence
Designed to fit a wide array of bench planes, including those made by some other manufacturers, this variable angle fence can be used left or right. Not just for right angles, the fence allows you to plane accurate and consistent angles from 45° to 135°.
Angles are set using a square or angle gauge, or directly on an angle you wish to match. A spring-loaded lever locks the fence and can...
Veritas Wide Router Plane Blades
These high-carbon steel router plane blades will fit the Veritas large and medium router planes, and the the Veritas hinge mortise plane, as well as Stanley #71 router planes (with the height-adjustment nut inverted). The narrow single-piece blades are available in five Imperial sizes
The 1/2" blades have a two-piece design and are available in two styles: straight and spear-point (for final...
Woodcarvers Mallet 10oz - Hornbeam
A locally made woodcarver's mallet, all the way from deepest, darkest Norfolk.
Designed by professional woodcarver (Gerald Adams) and made by Colin Dalton. Mallets are notoriously difficult to choose but this design seems a good weight and fits comfortably in the hand.
Seasoned Hornbeam head with Ash handle.
2¾" (70mm) head
8" (200mm) high
10oz (300g)
Woodpeckers Edge Rule 600mm
Woodpeckers Woodworking Edge Rule - Metric 600mm (Includes Edge Rule Stop)
Measuring the narrow edge of stock with typical rules is a little awkward. Getting the rule parallel to the stock and leaving yourself room to make a tick mark can become quite a juggling act. Working on the face of a piece is usually a little easier, but you can still struggle to jeep the rule parallel to your work. The...
Woodpeckers Edge Rule 900mm
Woodpeckers Woodworking Edge Rule - 900mm. Includes Edge Rule Stop.
Measuring the narrow edge of stock with typical rules is a little awkward. Getting the rule parallel to the stock and leaving yourself room to make a tick mark can become quite a juggling act. Working on the face of a piece is usually a little easier, but you can still struggle to jeep the rule parallel to your work. The Woodpeckers...
Woodpeckers in-DEXABLE Double Square
The Woodpeckers in-DEXABLE Double Square with 150mm metric blade and Rack-It.
The Woodpeckers in-DEXABLE Double Squares features the following......
Laser accurate scribing guides every millimetre.
Positive indexing every 30mm.
Laser engraved metric scales.
Sliding support tab to allow the square to rest on the edge of a board.
Rack-It to safely store your square on the workshop wall.
Woodpeckers Mini Engle Angle 3''
Woodpeckers Engle Angle 3'' (75mm). 2023.
All the same tricks of the larger 6'' tool but in a smaller package so it can get into tighter spots.
This tool is inspired by the vintage #30 Stanley Angle Divider from 1903. By fitting the connected legs into an existing corner, the tool bisects the angle automatically. This is particularly important when mitering trim for existing structures....
Woodpeckers Mini Square
Woodpeckers Mini Square
A very handy small square. Description from the Woodpeckers website........
''You can use any square for checking a chisel, but they're usually too long to clear the handle, not wide enough to make it easy to align to the edge and generally poorly designed for the job. That's why we came up with the Woodpecker Mini Square. At 1-1/8'' (28.5mm) x2,...
Woodpeckers Rule Stop 2
Woodpeckers Rule Stop-2.
Simply take any ruler and add this well engineered stop stop to help you repeat your accurate marking out.
Woodpeckers Woodworking Rule 600mm
The Woodpeckers Metric 600mm Woodworking Rule
A rule you can trust that has a very high level of accuracy. These rules are precision made from aircraft grade aluminium and anodized for surface protection and appearance. Woodpeckers say they are straighter, heavier and are easier to handle than any others on the market.
Left to right reading scale one side
Centre scale the other. The ''0''...
Woodpeckers Woodworking Rule 900mm
The Woodpeckers Metric 900mm Woodworking Rule
A rule you can trust that has a very high level of accuracy. These rules are precision made from aircraft grade aluminium and anodized for surface protection and appearance. Woodpeckers say they are straighter, heavier and are easier to handle than any others on the market.
Left to right reading scale one side
Centre scale the other. The ''0''...
Workshop Waist Apron from Lost Art Press
Shop aprons that cover the torso are great in cold climes, but they are impractical during the summer or in heated shops. For years, we tried using tool belts for carpentry, but those are designed for a ridiculous amount of equipment and a 50’ tape measure.
The solution that we love is a waist apron. It is compact and won’t leave a giant sweat stain behind like some shop aprons. And...