Sort By
Per Page
View
Grid
List
Slow Adjuster for Veritas Bevel-Up Planes - Type A
The fine thread on this Norris-style adjuster slows blade advancement, making it easier to set blade projection precisely. An easy retrofit, it simply replaces the regular adjuster supplied with our bevel-up planes.
Two versions are available. This type fits the bevel-up smoother, bevel-up jointer, low-angle jack, low-angle smooth and low-angle block planes.
Made in Canada.
Handles for Veritas Low-Angle Block Plane
The bevel-up configuration of the Veritas low-angle block plane lets you vary the blade angle to suit the task, from low-angle blades for use on end grain to high-angle blades on figured wood. However, steeper cutting angles require more force to push the plane—a challenge for those with small hands or less strength.
We offer inexpensive hardwood grips to adapt our low-angle block plane into...
Veritas Bevel-Up Jointer Fence
The Veritas low-angle jointer fence enables you to shoot consistent and accurate square or bevelled edges with your Veritas bevel-up jointer. The 11" long anodized aluminium fence can be attached to either side of the plane with the brass thumbscrews provided; a set screw can be adjusted to square the fence to the sole.
As supplied, the 2" tall guiding face can be used to plane edges perfectly...
Veritas Variable Angle Fence for Rebate Planes
This plane fence doesn't limit you to right angles - it allows accurate and consistent planing of any angle from 45° to 135°.
Angles are set using a square or angle gauge, or directly on an angle you wish to match.
The spring-loaded lever, which locks the fence, can be rotated out of the way if necessary.
Through-holes in the 11" long aluminium fence allow the attachment of a wooden...
Veritas Jointer Fence
Planing a square edge on a board requires a jointer fence, whether you are using an electric jointer or a hand plane.
The Veritas® jointer fence allows you to shoot accurate and consistent square or bevelled edges with most* iron or steel bench planes. The integral rare-earth magnets make it quick and easy to attach or remove the 11" long anodized aluminium fence from either side of all sizes...
Veritas Hand Jointer
The Veritas Hand Jointer allows you to accurately joint small parts by hand.
Box-making and modelmaking often require small parts that are too dangerous to run through a power jointer and difficult to joint with a hand plane; balancing a plane on pieces much smaller than its sole can be awkward.
This hand jointing accessory for Veritas medium and large shoulder planes lets you bring the work...
Veritas Wile Plane Hammer
Making fine adjustments to plane-blade position is easier with the right tool, and few can compare to the finely made plane hammers of Richard Wile, a hobbyist woodworker from Nova Scotia.
Based on Wile's design, this hammer is machined in our shop to have the same elegant proportions as the original, giving it a weight and balance that feel right in the hand. The small brass head, only 5/8"...
Veritas Wooden Plane Hardware Kit + PM-V11 Blade
With this kit (and basic woodworking skills) you can build a bevel-down wood-bodied smooth plane with a Norris-style mechanism for easy depth and lateral adjustment.
The kit includes a blade, a Norris-style adjuster with a steel cup to seat it in, plus a knob, tapped insert and cross pin for the lever cap, all made of brass. The lapped PM-V11 blade is 1/8" thick and 1 5/8" wide with a 25° bevel.
You...
New Veritas Micro-Adjust Wheel Marking Gauge
Veritas have refined and redesigned their ever popular wheel marking gauges. This new micro-adjust wheel marking gauge draws on two decades of manufacturing experience, with subtle improvements across the board.
The adjustment mechanism built into the stainless-steel rod is intuitive to use. After setting the approximate projection, you can fine-tune the position of the cutter within a range of...
Veritas Micro Adjust Marking Gauge
The Veritas wheel marking gauge is a great workhorse and excellent value. Its popularity led to the development of a second model that incorporates a micro-adjust feature. It is similar to our standard wheel marking gauge with an anodized aluminium body, brass face, stainless-steel rod and internal O-ring to keep a constant light friction force on the rod. It differs in that the body is slightly...
Veritas Dual Marking Gauge
The Veritas Dual Marking Gauge has two independently adjustable rods, which will allow you to set two measurements at once, so you can quickly alternate between them when transferring or marking repetitive dimensions. Projection up to 5-3/4" is easy to set, since an internal O-ring keeps light but constant friction on each rod; a thumbscrew firmly locks rods in place.
Like other Veritas marking...
Veritas Standard Marking Gauge
Standard Gauge - pretty much the same construction as the micro adjust but these are slighly shorter at 6" and do not have the micro adjust feature.
Veritas Marking Gauge Replacement Wheel
Replacement wheel for Veritas gauges. Not suitable for the new style micro-adjust marking gauge.
Veritas Marking Gauge Replacement Wheel - (Inside)
Replacement wheel for the Dual Marking gauges. Both the Inside and Outside cutters are required for the Dual Marking gauge.
Veritas Marking Gauge Replacement Wheel - (Outside)
Replacement wheel for the new style Micro-adust and Dual Marking gauges. Both the Inside and Outside cutters are required for the Dual Marking gauge.
Veritas Marking/Mortice Gauge Heads
Though designed for use with their Veritas® Wheel Marking Gauges, these gauge heads are a simple retrofit for any marking gauge with a 5/16" diameter shaft.
Made from carbon steel, the 5/8" diameter wheel cutters will scribe at any point in their circumference and slice rather than tear fibers for clean, accurate cuts. The single-bevel cutters are usable in-line for marking parallel lines, or...
Veritas Micro-Adjust Rod for Wheel Marking Gauges
We offer the micro-adjust rod separately from the gauge body to let you easily upgrade a Veritas standard wheel marking gauge you own with the new adjustment mechanism.
Veritas Shaft Clamp for Dual Marking Gauge
On occasions, it may an advantage to lock the relative position of the two rods on the Veritas® Dual Marking Gauge, such as when a project requires a constant mortise size, but different offsets. The shaft clamp lets you lock the relative position of the cutters while still being able to adjust the fence for offset. This allows you to preserve identical mortise or tenon sizing when joining parts...
Veritas Shop Marking Knife
The unique handle shape on this marking knife lets you use it comfortably with a pencil grip when fine control is needed, or a pistol grip that allows greater force to be applied for a more visible line.
The removable blade design lets you flip the blade for right-hand or left-hand use, or for flush registration on either side of a reference surface.
The blade, made of PM-V11 tool steel, is 3/32"...
Veritas Aluminium Straightedges
These anodized aluminium straight edges are 1¾" high and 7/16" wide, and will not rust. The reference edge is machined flat to within 0.003" over the entire length. They are available in three lengths, 24", 38" and 50". The 24" straight edge weighs 1lb, the 38" weighs just under 2lb, and the 50" version weighs 2.5lb.
Veritas Steel Straightedges
Shop accuracy begins with a benchmark straightedge as a surface reference. These Canadian-made Veritas precision steel straightedges are ground flat over the entire length on both edges, the 24" lengths to within 0.0010" and the 36" length to within 0.0015". All have been stress relieved to remain true under temperature variation. Useful for checking whether surfaces are flat or...
Veritas Low-Angle Block Plane + PM-V11 Blade
Veritas have made a block plane that uses a ''Norris'' style combined sideways (lateral) and up and down adjustment which gives you greater control when adjusting its impressive 1/8'' thick by 1 5/8'' wide PM-V11.
This plane also overcomes one of the drawbacks of other block planes in having higher side wings (ideal for shooting) with finger grips in each side. The...
Veritas DX60 Block Plane + PM-V11 Blade
This Veritas DX60 block plane is one of the finest planes that Veritas have ever made. 4 years of design work culminates in a superb plane made to exacting standards and featuring newly refined stainless-steel hardware.
The knob and wheel have elegant elliptical knurled edges for a firm grip. The lever cap has been extensively redesigned to integrate cleanly with the plane body and provide an...
Veritas Standard Angle Block Plane + PM-V11 Blade
This is the standard angle version of the Veritas low angle block plane.
Preferred for general-purpose work, the 20° bed angle plus the 25° bevel angle on the bevel-up blade result in an effective cutting angle of 45°, the same as found in most bench planes.
A low-profile lever cap results in a plane that fits the hand well, at only 1/8" higher than its low-angle sibling.
Mechanically,...
Veritas Skew Block Plane + PM-V11 Blade
The Veritas Skew Block Plane is a versatile plane that excels at trimming rebates and planing end grain. Of course, you can also use it as a normal block plane. Its Norris-style adjuster guarantees precise blade setting. Machined and surface ground, the 162 x 44mm body is ductile cast iron. It has a 12° bed angle and a movable toe fully enclosed by the body casting. A Bubinga knob locks the toe...
Veritas Pocket Plane + PM-V11 Blade
The Veritas Pocket Plane at just 4½" long and 1¼" wide overall, and weighing just less than 11oz, is aptly named - it's small and light enough to carry in an apron pocket all day.
Designed with a bevel-up configuration and a fully functional combined feed and lateral adjustment mechanism, it has a finer cutting action than you might expect from such a small tool. This makes it admirably suited...
Veritas Apron Plane + PM-V11 Blade
This small, low-angle block plane from Veritas is the answer to a trim carpenter's prayers. At only 14oz it is half the weight of a standard block plane, a significant factor if you want to carry it with you all day.
The 5½" long, tough ductile cast iron body will take job-site accidents in stride. This is not a plane body that will break when dropped. It has good hand feel; the unique side...
Veritas Bevel-Up Smoother Plane + PM-V11 Blade
The latest addition to the Veritas family of low-angle bench planes is the state-of-the-art pure smoothing plane. It is the plane to use for the final finish on surfaces, especially woods of difficult grain patterns. It also complements the low-angle jack plane.
Veritas have combined the generous width and weight of a dedicated smoother with the versatile inner workings of a low-angle bevel-up...
Veritas Low-Angle Smoothing Plane + PM-V11 Blade
The Veritas low-angle smooth plane has three key uses. It is used to smooth large surfaces, preferably taking a diagonal cut, partly across and partly along the grain. Similarly, with its generous sides, it is ideal for shooting mitres. Finally, it is excellent for end-grain work. The low cutting angle of 37° minimizes fibre tearing. With a bed angle of 12°, this is a "bevel-up" plane, like a low-angle...
Veritas Small Bevel-Up Bench Plane + PM-V11 Blade
This Veritas low angle smoother is 225mm long, 59mm wide and weighs only 1.25kg. It is easier to handle than a full size smoother. Think of it lying somewhere between a large block plane and a full size smoother, then you’ll see just how useful this plane can be.
Like a full size version, it is useful for final finishing of surfaces, end-grain work and for shooting mitres. The ductile cast...
Veritas Bevel-Up Jointer Plane + PM-V11 Blade
The Veritas low-angle jointer is the largest member of the Veritas bevel-up bench plane family. At 22" x 2.7/8" and weighing 7½lb, it is the answer for jointing edges and flattening large panels.
The bevel-up blade configuration results in a plane that is versatile and straightforward to use. The 12° bed angle, coupled with the 25° blade bevel, creates an effective cutting angle of 37°. Simply...
Veritas Low-Angle Jack Plane + PM-V11 Blade
The Veritas® low-angle jack plane is an exceptionally versatile plane. It excels at end grain work, is great for shooting, and also works well for smoothing. With the optional high-angle blade, it is also the answer for working difficult grain, making it a well-rounded workhorse.
Veritas have designated it as a 62½ because of its generous size, heavier weight, low center of gravity...
Veritas Router Plane
Veritas Router Plane
Veritas Medium Router Plane
Slightly larger than the Veritas small router plane, this tool has the advantage of using the same blades as our full-size router plane.
For general use, the blade may be positioned inboard with the sole encircling it for maximum registration on the workpiece, even when approaching from the side or working an edge. This allows it to bridge recesses, providing great stability even on narrow stock....
Veritas Small Router Plane
The Veritas Small Router Plane is a versatile tool for fine work, particularly on narrow material or in confined areas, this small router plane is invaluable for any task requiring small recesses, grooves or dadoes.
The sole is designed to completely encircle the blade when in the closed-throat position for maximum registration to the workpiece, even when approaching from the side or working...
Veritas Narrow Router Plane Blades
These high-carbon steel router plane blades fit the Veritas large and merdium router planes, as well as Stanley #71 router planes (with the height-adjustment nut inverted). The narrow single-piece blades are available in both metric and imperial sizes.
Please note that Veritas do not produce a 3mm and a 1/8" blade, they consider them close enough in size so we only advertise the 1/8".
Sizes...
Veritas Wide Router Plane Blades
These high-carbon steel router plane blades will fit the Veritas large and medium router planes, and the the Veritas hinge mortise plane, as well as Stanley #71 router planes (with the height-adjustment nut inverted). The narrow single-piece blades are available in five Imperial sizes
The 1/2" blades have a two-piece design and are available in two styles: straight and spear-point (for final...
Veritas Fence for Large Router Plane
A very popular addition to the Veritas large router plane. Can be positioned on either side of the plane and will work on both straight and curved pieces.
Replacement 1/4' Blade for Veritas Small Router
Veritas Replacement 1/4" wide high-carbon steel blade for the .
Made in Canada.
Veritas Skew Rabbet + PM-V11 Blade
Like the Stanley #289 that inspired it, it is configured with a blade skewed at a 30° angle to reduce cut resistance, aid in shaving clearance, and help pull the fence tight against the workpiece. Because the blade sits flush with the side of the plane body, corner cuts are clean and accurate.
Adjustable in two axes (vertical and horizontal) for depth and projection, the scoring spur sits...
Veritas Side Rabbet Plane
The Veritas Side Rabbet Plane is used for cleaning up or trimming sidewalls of rabbets, dadoes or grooves to yield a perfect fit with its mate. It has a practical dual-blade configuration, coupled with an ingenious pivoting handle that permits right- or left-hand use to accommodate grain direction.
The thin sole functions much like a skate, allowing use in slots as narrow as 3/16" and to a depth...
Veritas Jack Rebate Plane + PM-V11 Blade
This Veritas Jack Rebate plane cuts large-scale rebating down to size. The body is 385mm long and the blade extends the full width (57mm) of the body. It is suitable for very large rebates and fielded or bevelled panels. The long sole and substantial mass help ensure accuracy.
The 4.8mm thick bevel-up blade makes right or left-handed corner cuts cleanly and accurately. Adjustable scoring spurs...
Veritas Bullnose Shoulder Plane + PM-V11 Blade
The Veritas® bullnose shoulder plane, perfect for cleaning up machine-cut joints, will be one of the most useful hand joinery tools you'll ever own.
Designed for maximum versatility, it performs as either a bullnose or a chisel plane as required. Simply loosen the brass toe-locking knob to remove the toe piece for chisel plane configuration, and you can work right up to a blind corner. An adjustable...
Veritas Small Shoulder Plane + PM-V11 Blade
Designed to seat nicely in the hand, the smallest Veritas shoulder plane is easily controlled using a one-handed grip.
The lever cap wraps around the rear of the body, shrouding the blade adjustment mechanism so it does not obstruct the grip while acting as a comfortable rest for the palm.
The through-hole and textured recesses cast into the side of the body provide grip points for fingers.
The...
Veritas Medium Shoulder Plane + PM-V11 Blade
The shoulder plane (a specialized rebate plane) is the ultimate tool for trimming a joint to a perfect fit. There is no better plane for trimming the shoulder of a tenon to perfection or for rebating work.
The Veritas® medium shoulder plane is proportioned for versatility; it measures 7" long by 0.700" wide and weighs 2 lb. The ductile cast iron body is accurately machined and ground so that...
Veritas Large Shoulder Plane + PM-V11 Blade
The Veritas® large shoulder plane (a specialized rabbet plane) is the latest and largest in our line of shoulder planes. Its size and mass make it perfect for trimming breadboard tenons, adjusting shoulders, or even paring down tenon cheeks. At 8¼" long, 1¼" wide and weighing 3¾ lb, it brings both authority and precision to larger work. The ductile cast iron body is accurately machined and ground...
Veritas Detail Rabbet Plane
The detail rebate plane is primarily useful for small trimming tasks. It is handy for getting into tight spaces, especially cleaning up the bottom of dados or grooves. The plane’s body is ductile cast iron, 75mm long, accurately machined and ground. The sides are flat and square, allowing you to use the plane on its side for trimming tenons. The low 15-degree bed angle combined with the 30-degree...
Veritas Shooting Plane + PM-V11 Blade
The mass of this Veritas Shooting Plane, its long base and low centre of gravity make it both stable and effective. Tipping the scales at just over 3.5kg and just under 400mm long, it is a substantial plane; you will appreciate the authority it provides when shooting.
The body is fully stress-relieved, ductile cast iron, with a sole and running surface machined flat and square to one another;...