Sort By
Per Page
View
Grid
List
Replacement Blade for Veritas Power Tenon Cutters
This replacement blade is for Veritas Power Tenon Cutters and it fits all sizes.
Veritas Small Tapered Reamer
The Veritas small tapered reamer 5mm to 19mm (3/16" to 3/4") is useful to rustic furniture makers for back-tapering holes for through-tenon wedging.
The bit is 85mm overall length with an 8mm hex shank.
Designed for use in an electric drill, these tools may also be used in a traditional brace.
Veritas Large Tapered Reamer
The Veritas large tapered reamer 5mm to 30mm (3/16" to 1-3/16") is useful to rustic furniture makers for back-tapering holes for through-tenon wedging.
The bit is 140mm overall length with an 8mm hex shank.
Designed for use in an electric drill, this tool may also be used in a traditional brace.
The Veritas small tapered reamer 5mm to 19mm (3/16" to 3/4") is useful to rustic furniture makers for...
Veritas Tapered Reamer Pro
The Veritas Tapered Reamer Pro is designed for use in a hand brace, our pro reamer offers excellent control and good cutting capability for general woodworking. It is particularly useful for tapering through holes where you want to be able to wedge tenons, such as in chair construction.
This reamer has a cast steel alloy body, a separate spring-steel blade, and a pair of blade-adjusting set screws.
When...
Veritas Dowel Formers - Metric
This Veritas dowel former allows you to make dowel pins of whatever length you need. You simply drive an oversized piece of wood through the sharp edged hole of the solid A2 tool steel insert to shear excess material from the dowel. The Veritas 75mm diameter mounting plate has two screw holes for permanent mounting.
Can be used over a 3/4" or 20mm dog hole and is compatible with all inserts. Solid...
Veritas Dowel Maker Master Set
The Veritas® Dowel Maker lets you make perfectly sized dowel from 1/4" to 1" dia. in 1/16" increments, up to 4' long (or longer in the larger diameters) from any wood species you wish. The process uses two blades (both highly wear-resistant A2 tool steel), one for roughing and the other for final sizing. You just rip square stock 1/8" oversize and drive it through the dowel maker using a square...
Veritas Tapered Snug Plug Cutters
Sometimes when plugging holes, no matter how carefully drilled, the holes finish up slightly oversize for the plug, especially in soft woods. These Veritas cabinet maker's snug plug cutters overcome this by cutting a slightly tapered plug.
The first 3mm of the plug is the diameter stated whilst the remaining length is then flared out at an angle of 3°. Just tap the plug into place until you...
Curved Replacement Blade for Veritas Dowel & Tenon Cutters
The curved blade is a replacement blade for the Veritas Dowel and Tenon Cutters. It can also be used on the 3/8", 7/16" and 1/2" Veritas Tapered Tenon Cutters (not recommended for the larger sizes as overheating may occur).
Veritas Power Tenon Cutter Sharpening Kit
Each Veritas Power Tenon Cutter sharpening kit consists of:
1½" x 1½" Sanding Drum.
Pack of 3 x 80 grit Silicon Carbide Sleeves
Pack of 3 x 120 grit Silicon Carbide Sleeves
Veritas Cabinetmaker's Mallet
The Veritas Cabinetmaker's Mallet is wooden, these are well suited to shop work such as driving chisels or larger carving tools. Although they tend to be bulky, the wooden striking faces are much kinder to tool handles than steel-face hammers.
Inspired by a vintage tool in the Lee Valley collection, this mallet has the best features of both wood and metal and is a direct substitute for a carpenter's...
Veritas Large Journeyman's Mallet
The Veritas Large Journeyman's Mallet has a solid brass head, a walnut handle and a simple, refined profile, making it an elegant and effective mallet.
Designed for work that requires more finesse than power, it can be held by the handle or used with the head cradled in your palm, allowing you to more precisely control the force of blows. The head is attached to the handle with a blind threaded...
Veritas Carvers Drawknife - PM-V11
An ordinary drawknife is too large for most carving - the Veritas drawknife is designed for ease of use with maximum control.
The teardrop-shaped handles are cocked at 45° to the blade and nestle comfortably in your hands. The polished 4" x 1/8" x 3/4" blade is ground and honed to a perfect edge, and is supplied with a blade guard.
The drawknife blade is custom made for us...
Veritas Chair Devils
Veritas Chair devils are wonderful tools for final shaping and smoothing of round parts such as chair spindles and posts. The specially shaped scraper blade rounds the workpiece, removing any spokeshave marks.
• Machined steel bodies fitted with hardwood handles
• Machined toe and two thumbscrews are solid brass
• High-carbon steel blades are 0.040'' thick, hardened...
Veritas Flat Spokeshave PM-V11
The Veritas flat spokeshave has a 1/8" (0.125") thick PM-V11 tool steel blade, seated at 45° to the sole.
The thick blade, carefully machined lever cap and blade bed all combine to produce chatterfree cutting in most situations.
The ductile cast iron body is fitted with African rosewood handles that are shaped for comfort and control, offering several ways to grip the tool comfortably...
Veritas Round Spokeshave PM-V11
The Veritas Round Spokeshave has a 3.2mm thick PM-V11 steel blade, which fits perfectly onto the machined blade.
The ductile cast iron body is fitted with hardwood handles, shaped for comfort and control. The toe serves as a thumb rest allowing the user to choke up on the body to attain exceptional control. Twin adjustment wheels quickly and accurately control cut depth and skew and shims let...
Veritas Concave Spokeshave PM-V11
The Veritas Concave spokeshaves have a extremely durable PM-V11 steel alloy blade, seated at 45° to the sole. The thick blade, carefully machined lever cap and blade bed all combine to produce chatterfree cutting in virtually all conditions.
This spokeshave is popular with chair and paddle makers, being the first choice for a wide range of jobs from small spindles to large oars.
The ductile...
Veritas Low Angle Spokeshave
The Veritas Spokeshave uses a basic traditional shape, not of the spokeshaves of the last century, but of the century before.
Until about 1900, the vast majority of spokeshaves were low-angle spokeshaves with wooden bodies. The blades were hand forged with upturned tangs that fitted into holes pierced in the body of the shave. Wedged in position, they were adjusted by tapping the ends of the...
Veritas Miniature Planing Stops
The Veritas miniature planing stop is designed to slip over a pair of miniature surface dogs (sold separately) to provide a reliable registration surface when working on thin or narrow workpieces, allowing materials to be worked without obstruction.
For tasks that involve the application of horizontal force in one direction, such as planing, a single stop can be used with no additional clamping....
Veritas Miniature Work Surface
The Veritas 11'' × 8'' miniature Worksurface is made from 18mm Baltic birch plywood and features an array of 17/64'' diameter dog holes, spaced 1 1/2'' apart.
It can be used in combination with the four miniature workbench accessories (Wonder Dog, hold-down, surface dogs and planing stops).
Four rubber feet help prevent the platform from shifting in use.
Made...
Veritas Miniature Wonder Dog
This 1:3 scale version of the Veritas Wonder Dog is especially useful for securing small work horizontally. Sized to fit in a 17/64'' dog hole, it has a 1 1/2'' long stainless-steel post with an O-ring for slightly elevated clamping.
At 3/4'' wide and 1/4'' high, the brass head will not mark tools or workpieces. The clamping screw provides approximately 1 1/4''...
Veritas Set of Miniature Surface Dogs
Just like its full-size version, this functional 1:3 scale surface dog has a flat face for work registration and a rim that supports and stabilizes it on a miniature workbench. The post fits in a 17/64'' diameter dog hole, resisting movement from horizontal forces. The face is 11/32'' × 3/16'' tall. Solid brass, the surface dog is non-corroding and kind to your tools.
To...
Veritas Miniature Hold-Down
This 1:3 scale miniature version the Veritas hold-down can secure work vertically on small projects, such as when cleaning up dovetails or chopping mortises.
The low-profile 3'' cast steel arm is unobstructed at the clamping end, allowing good access to work from all sides. Simply turn the brass knob to apply the desired amount of clamping force. The 3'' post fits in a 17/64''...
Veritas Mk.II Honing Guide
The key to consistent and fast honing is repeatability - and this guide delivers it in spades. Whether you're a sharpening veteran or just starting out, this versatile guide lets you concentrate on sharpening without worrying about controlling blade angle at the same time. This makes your honing reliable, accurate and consistent. Three options let you choose the honing guide that best suits your...
Veritas Side-Clamping Honing Guide
The tried-and-true design of a side-clamping guide is familiar to most woodworkers. This side-clamping honing guide is a piece of modern-day engineering that improves on this established design while maintaining the flexibility of this type of guide. Chisels and plane blades ranging from 1/8" (3mm) to 2½" (63mm) fit securely for accurate honing. The unique three-point holding position...
Veritas Short Blade Honing Guide
A frequent challenge faced by sharpeners of all skill levels is the safe and accurate honing of small or short blades. Spokeshave, small block plane and palm plane blades are too small for most guides. This short blade honing guide has the flexibility to hold small blades that other honing guides cannot handle.
Blades up to 2 5/8'' wide are easily aligned with the included registration jig...
Veritas Small Blade Holder
The Veritas Small Blade Holder helps with the difficulty of holding short blades such as those found in most spokeshaves, instrument maker's planes, etc., sharpening them has been difficult.
The Veritas Small Blade Holder solves this effectively and safely by securing the blade using two powerful rare-earth magnets embedded into anodized aluminium and an adjustable stop block. In effect, it...
Veritas Mortice Chisel Adapter for Veritas Mk.II Narrow-Blade Honing Guide
This Veritas Mortice Chisel Adapter for the Mk.II honing guide expands its blade-holding capacity to allow consistent, accurate honing of mortice chisels. It increases the space between the roller base and the blade carrier to accommodate the thicker blades of mortice chisels, holding blades up to 11/16" thick.
Compatible with the narrow-blade clamping heads, the adapter is configured so...
Veritas Basic Grinding Set
The Grinding Jig works with any power or hand grinder that has a tool rest. The back plate is offset for short chisels, such as Japanese or western butt chisels. The brass clamping bolts have nylon washers to prevent galling; other parts are made from hard aluminum, further hardened by anodizing to prevent wear. High-friction pads ensure solid clamping without inadvertent misalignment. Fits most tool...
Veritas Grinder Tool Rest
The major weakness of most bench grinders is that the tool rests are virtually useless. It is nearly impossible to find one with a rest that is solid and square.
The Veritas® Grinder Tool Rest can be used with 6" or 8" utility bench grinders and many belt sanders/grinders. It mounts directly to the bench in front of the grinder and can be readily folded out of the way for freehand grinding....
Veritas Grinding Jig
The grinding jig works with any power or hand grinder that has a tool rest.
Put a tool in the jig, slide it against the alignment pin and one clamping thumbscrew to square it, adjust the blade projection for bevel angle, and tighten in place. The tool is now held squarely in the jig at the chosen bevel angle. Slide the jig back and forth across the tool rest and stone face to sharpen the tool....
Table for 1 1/2'' Wheels for Veritas Grinder Tool Rest
This replacement table for the Veritas grinder tool rest has a wider slot to let you use it with 1 1/2" wide wheels (like 8" CBN wheels).
The 4" wide aluminum table has a 1 5/8" wide slot and installs easily in place of the standard table. It has the same horizontal slot and center hole for use with sliding and rotating jigs.
(For wheels narrower than 1 1/2", the standard...
.png "Last Ones!")
Veritas Jointer Blade Sharpener
A commercial sharpening service or a sophisticated home grinder is necessary for badly nicked blades. The Veritas Jointer Blade Sharpener is designed to restore blades dulled from normal use, even if they contain minor nicks.
It clamps blades up to 8" wide (including hand-plane blades) for sharpening on PSA-backed abrasives. Just stick the abrasive to a flat surface (plate glass works well),...
Veritas Miniature Honing Guide
It may be stating the obvious, but at some point the blades of the Veritas miniature tools will require sharpening and honing. This 1/3 scale version of the Veritas Mk1 honing guide is a natural extension to the Veritas miniature tool collection. This fully functional honing guide will help keep the miniature blades in peak condition.
The guide consists of a honing guide and an angle jig. The honing...
Veritas Steel Honing Plate
The Veritas Steel Honing Plate measures 204 x 76 x 9.5mm and weighs 1.1kg.
Precision-ground to flatness tolerance of 0.127mm (0.005").
An excellent substrate for diamond paste (available separately).
Made of dimensionally stable low-carbon steel to retain its flatness. Surface pattern helps capture diamond grit without compromising flatness.
The plates can be glued to a backing board...
Veritas Bevel Gauge
Half the secret of sharpening is the control of blade geometry.
Nothing is handier than a bevel gauge for quickly checking the grind angle of chisels, plane blades, turning tools, etc. A quick check confirms the angle last used for grinding or honing so that the edge geometry can be maintained.
Our bevel gauge has seven individual slots that will measure the most commonly used angles from 15°...
Veritas Saw File Holder
Not only does this Veritas Saw File Holder provide a secondary grip for your saw file, it also helps you control the angle of the file as you sharpen, using the eye's natural ability to judge parallel and level.
It has a rotating collar for setting a positive or negative rake angle up to 30°, and a 3" wide protractor to set the fleam (or bevel) angle up to 45° left or right. All you need to...
Veritas Lapping Grit 90x Silicon Carbide 4oz
Silicon carbide is ideal for flattening oil and water stones or lapping plane bottoms and blades. Just sprinkle the grit on a piece of glass or a steel lapping plate, add a shot of oil or water (as required), and lap the item flat. This fast and easy process lets you keep all of your stones dead flat.
90x is used for most applications.
Using PSA-backed plastic laminate sheets on glass speeds...
Veritas Lapping Kit Set of Five 2 oz Containers - 05M0101
Silicon carbide is ideal for flattening oil and water stones or lapping plane bottoms and blades. Just sprinkle the grit on a piece of glass or a steel lapping plate, add a shot of oil or water (as required), and lap the item flat. This fast and easy process lets you keep all of your stones dead flat.
A set of five 2 oz containers of 90x, 180x, 280x, 400x and 600x and instructions. 90x is used for...
Veritas Planing Stop
These low-profile work stops present a broad bearing surface. Particularly useful with thin or narrow workpieces, each 1 1/4" wide anodized aluminum rail projects just 0.22" above the bench top, allowing materials as thin as 1/4" to be worked or planed without obstruction. It also provides a reliable registration surface for materials too narrow to span two adjacent bench dogs.
The...
Muzzles for Veritas Bench Dogs & Pups
For clamping a finished piece without marking it, the slip-resistant muzzles slide over the Bench Dogs (or Bench Pups) to give you a non-marring surface. They have a hard, spring-grip, plastic body with six face ribs.
Available in two sizes: 1¼" long for Bench Dogs or 3/4" long for Bench Pups. Sold in pairs.
Accessories for the Veritas Wood Carver's Vice
Accessories for the Veritas Wood Carver's Vice:
Dog Hole Mount Assembly:
The vice can be side or top mounted through any standard 3/4" dia. dog hole using the auxiliary rod/sleeve/wing-nut assembly, usable on benches from 5/8" to 4" thick.
3 1/2" Mounting Plate:
3-1/2" dia. by 1/2" thick mounting plate with a steel rod.
2" Mounting Plate:
For mounting smaller pieces, such as duck heads or bird...
5 1/2'' Post for Veritas Bench Hold Down
This 5 1/2" Post is for the Veritas Bench Hold Down, for holes where through travel is limited.
At just 5-1/2" long, it provides about 4" of clamping capacity.
Patented.
Veritas Tail Vice Screw
The tail vice screw is essentially the same construction as a shoulder vice screw but without an end guide, this tail vice screw has a clamping capacity of 17" less thickness of wooden jaws (not included) and is 21" overall.
1.1/8" diameter screw with single-lead Acme threads.
Mounting screws included.
Wooden Handle not included, but can be purchased as an optional extra.
Made...
Veritas 3/4'' Surface Clamp
Hold down, bench clamp or surface clamp - the functions are the same just the name changes. True to form Veritas have taken an ordinary thing and made it much, much better - as well as a thing of beauty in brass and black satin.
These fast acting surface clamps can be used anywhere you can drill a 19mm diameter hole. The post has a wedging mechanism which anchors it firmly (horizontally or vertically)...
Veritas Bench Dogs & Pups
These are made from solid brass rod. Sold in pairs.
The crosshatching and 2° slope on the face help to hold wood securely, pulling it down onto the bench's surface. A side spring slides cleanly and holds it in position.
The dogs are 110mm (4.3/8") long, the pups 60mm (2.3/8").
Both work well in combination with Veritas Wonder Dog and Wonder Pup Clamps. For 19mm (3/4")...
Veritas Bench Hold Down
The Veritas hold-down can clamp workpieces to a bench or anywhere a 3/4" hole can be drilled.
Exceptionally high clamping forces can be obtained with this hold-down for two reasons. First, with the arm free to pivot independently, all levered forces are exerted downward, without any losses due to horizontal slippage from the canting action of the hold-down post. Second, the fine barb-shaped grooves...
Veritas Carvers Screw
Turned from a solid bar of brass, this carver's screw, with its tapered tip and high-profile threads, grips securely and guarantees that remounted pieces are held as securely the third and fourth time as they were the first.
The hex portion clamps securely in a vice while you thread on a blank, or you can use a spanner. The moulded tightening knob has a low-friction brass insert. At 5" long overall,...