Best Selling

Boxed in good condition. G ++ This is popular with chairmakers for hollowing out seats etc. Available brand new for around £130 Little used with some minor tarnishing to handles. Full blade. A commission sale.

Brass Cutter Holder for use with Revolution Hollowing System

Fine condition used only once. Comes with the 3/8" Square Drive Adapter and 1/2" Square Socket. Original box and instructions. Obtaining dowels to perfectly match a project or specific species of timber, is to say the least, almost impossible. Not so if you own a Veritas Dowel cutter and have a few timber off-cuts to hand. These cutters can be used two ways. Either use them like a hand-held...

Woodcarvers Punches from Henry Taylor which are made here in the UK. They are approximately 75mm (3'') in length and approximately 5mm wide.

Woodcarvers Punches from Henry Taylor which are made here in the UK. They are approximately 75mm (3'') in length and approximately 5mm wide.

This tapered square-shank adapter lets you use the 5/8'' (16mm) to 1'' (25mm) power tenon cutters with a hand brace.

Pre-owned but little used in Lie-Nielsen leather case.

A 12'' Swan Neck for use with Revolution Hollowing Sytem supplied with Egg Scraper (REV13), 1/2'' diamter shaft.

The Crown Tools Revolution Texturing Tool fits directly into the 1/2'' (13mm) collet of the Revolution Handle and is supplied with a 18 tooth texturing wheel. The blade has an indexing line scribed down the centre to allow the use of Crown Tools Indexing Tool. Adding the Indexing Tool with the appropriate Spiralling Wheels available offers full spiralling capabilities.

18 Tooth texturing wheel, wheels are approx 37mm diameter with 8mm central hole.

Yes! The blacksmiths at legendary French artisan tool makers AURIOU TOOLWORKS also used to make tools for stone sculptors who use air powered chisels for their work. A bit noisy for us (and them maybe because they have stopped making them!) We have 3 gouges: 10mm wide, 15mm wide and 20mm wide. Also 2 snakes tongue (pied a biche) tools - for heavy shaping work (10 & 15mm wide) And 2 point...

New This system (RSTM-SCT3) comes with the carbide square cutter plus the following titanium nitride cutters RSTM-GT2 Excelsior Detail Point Cutter RSTM-GT4 Excelsior French Curve Cutter RSTM-GT6 Excelsior Teardrop Inside/Outside Cutter RSTM-GT7 Excelsior Mushroom Cutter

Brusso Hardware (USA) discontinued a lot of their range over the last few years. Most of their range of stainless hinges left their portfolio but we have a few pairs left (5 pairs) in stock. These are new. The Brusso CB-302 full mortice butt hinge, measures 1¼" x 13/16". Length: 1.250" - 1¼" - 32mm Width: 0.802" - 13/16" - 21mm Leaf Thickness: 0.086" - 5/64" - 2mm NOTE - All Brusso hinges...

This is old stock from the early days of starting up Classic Hand Tools. Sanderson Hardware are still going in California. (Note - these cotter pins are different to what they offer now). The diameter of the ring pull is 3/4". The rod stock is 1/8" diameter and 2 1/4” ong . The square plate is ¾” x 5/8” with 4 screw holes (screws provided). The plate has...

A cap iron serves to stiffen a plane blade, helping to dampen vibration and reduce the potential for blade chatter. Made of corrosion-resistant A2 steel, our 1/8'' (3.17mm) thick cap irons are sized to fit Stanley and Record planes. The leading edge of the cap iron is machined with a relief angle to ensure it always contacts the face of the blade, so no gap can form. Made in Canada.

Top-quality replacement blades for Stanley #51/#52 and Record/Stanley #151 spokeshaves. Produced by Veritas in their PM-V11 (Rc61-63) tool steel, the blades are 2 1/8'' (54mm) wide by 1 7/8" (47mm) high, have a 30° bevel and are lapped on the face to a flatness tolerance of 0.0005" (0.0127mm) or better over the entire surface. The blades are a hefty 3/32'' (2.4mm) thick...

The Veritas honing compound, which took over two years to develop, is the most effective on the market. It is a blend of both chromium and aluminium oxide to give the best combination of cutting speed and fine finish. The bonding is formulated for ease of charging. It will adhere equally well to felt, leather or wood. Cuts quickly but leaves a mirror finish with a light wax film. The average...

Veritas developed these smaller-diameter tenon cutters for use with small stock. Available in six cutting diameters from 1/4'' to 9/16''. The 9/16'' tenon is the size used historically for chair rungs. The other sizes (1/4'' to 1/2'') are useful in many areas, e.g., members within trellis or lattice work. All sizes have a straight blade that cuts a 60°...