Sort By
Per Page
View
Grid
List
Veritas Quick-Release Front Vice
Using the same quick-release mechanism as our tail vise, our front vise has a simple on-off cam lever to engage or disengage the Acme-threaded screw, allowing it to apply up to 400lb of force in either clamping or spreading applications.
The screw mechanism provides 12¼" of overall travel (less the thickness of your wooden jaw and bench apron). Tight body tolerances result in minimal jaw sag,...
Veritas Quick-Release Sliding Tail Vice
Installing a tail vise is notoriously difficult, usually requiring a section of workbench to be cut away and rebuilt around a complicated vise mechanism. Not so with this one. It can be quickly incorporated into a new bench construction or easily retrofitted to an existing bench without major surgery.
The end plates are symmetrical, so you can install the T-handle and quick-release lever in a...
Veritas Quick-Release Wonder Dog
This version of the Wonder Dog has a fast-acting cam mechanism to speed up adjustments. You just slide the head against the workpiece, then throw the lever to apply clamping force. Curved and irregular shapes can also be clamped; two screw holes in the brass dog head let you attach a custom face of any shape, giving good control without marring work.
The low-profile head and clamp body are 5/8"...
Veritas Reeding Blades for Combination Plane
For use with the combination plane only, these PM-V11 steel reeding blades are available in two-, three- and four-reed versions, with 1/8", 3/16" or 1/4" diameter reeds. A 1/16" groove (also known as a quirk) is cut on either side of each reed. Made in Canada.
Replacement 1/4' Blade for Veritas Small Router
Veritas Replacement 1/4" wide high-carbon steel blade for the .
Made in Canada.
Veritas Fence for Large Router Plane
A very popular addition to the Veritas large router plane. Can be positioned on either side of the plane and will work on both straight and curved pieces.
Veritas Ruler Stop
The Veritas ruler stop increases the usefulness of a metal ruler by providing a solid reference point. It is ideal for setting saw fences, repeat cuts, etc.
To use, slide the stop over the ruler end and tighten it at the desired position. The notched post at the tip of the brass adjustment screw allows even the thinnest rulers to be clamped securely; it will not mar the ruler edge. Repositioning...
Veritas Saddle Square
Veritas Small Saddle Square - Transferring a line from one surface to another with a small square is not easy. Our saddle square allows you to scribe two perpendicular surfaces at one time. But, more importantly, it allows you to pick up on a line already scribed & accurately transfer it to another perpendicular face. With 1 1/4" (32mm) & 2 1/4" (57mm) inside legs, it can wrap a...
Veritas Saw File Holder
Not only does this Veritas Saw File Holder provide a secondary grip for your saw file, it also helps you control the angle of the file as you sharpen, using the eye's natural ability to judge parallel and level.
It has a rotating collar for setting a positive or negative rake angle up to 30°, and a 3" wide protractor to set the fleam (or bevel) angle up to 45° left or right. All you need to...
Veritas Saw Guide Clamps
These Veritas Saw Guide Clamps are 50mm capacity clamps are anodised aluminium with solid brass screws and pads. They fit into the T-slot on the underside of the saw guide leaving the upper surface clear.
These clamps ensure the guide is secure and firmly held in place resulting in a higher degree of accuracy. Note they can also be used with the magnetic saw guide.
Veritas Scraper Holder
There is no tool handier in the workshop than a cabinet scraper, and this holder lets you use it to maximum advantage.
The light, strong, glass-filled nylon body, with all brass fittings, is kind to a sharp hook. You can slip any thickness of scraper (6"/150mm long) into it, clamp it in position, and set the amount of bow with the screw-actuated centre pad.
The body is moulded to fit your hands...
Veritas Scraper Shave
The Veritas Scraper Shave is a versatile small scraper suitable for small-scale work, fine detailing, or any application where a normal scraping plane would be too large.
The design of the tool allows a controlled scraping action that effectively smoothes the workpiece. Can be used as a companion tool with the chair devils for smoothing of non-round chair parts such as crest rails, arm bows and...
Veritas Scrub Plane + PM-V11 Blade
The scrub plane is the tool of choice for major stock removal, the first step when flattening rough stock by hand. Much like a low-angle smooth plane, a scrub is not usually used parallel to the grain, but at an angle of 30° or more. The blade edge is ground with a 3" radius, so that it takes an aggressive cut. This is the tool you use to get stock into a condition where you then can use a...
Veritas Shaft Clamp for Dual Marking Gauge
On occasions, it may an advantage to lock the relative position of the two rods on the Veritas® Dual Marking Gauge, such as when a project requires a constant mortise size, but different offsets. The shaft clamp lets you lock the relative position of the cutters while still being able to adjust the fence for offset. This allows you to preserve identical mortise or tenon sizing when joining parts...
Veritas Shooting Board
The 24" long shooting track fits the Veritas shooting plane.
This is a shooting board that doesn’t limit you to one angle, the fence is adjustable to let you shoot up to 60° from square. A spring-loaded button registers in fixed detents at 0°, 18°, 22.5°, 25.7°, 30°, 36°, 45° and 60° to let you quickly set the fence for square angles as well as miter cuts to produce frames with ten,...
Veritas Shooting Board Fence
The Veritas Shooting Board Fence Kit lets you construct a shooting board that doesn’t limit you to one angle – the fence is adjustable to let you easily shoot mitres of various angles. A spring-loaded button registers in fixed detents at 0°, 18°, 22.5°, 25.7°, 30°, 36°, 45° and 60° to let you quickly adjust the fence to shoot square angles as well as mitres for frames with ten, eight,...
Veritas Shooting Board Track
These are straight, durable aluminium tracks for making your own shooting board. They are designed to fit the Veritas Shooting Plane, and any other plane with a running surface between 2-1/32" and 2-1/4" wide; you can adjust the stainless-steel outer rail for a perfect fit. Set screws keep the rail from shifting in use.
The inner rail is 11/64" tall. Low-friction UHMW strips in the...
Veritas Shoulder-Vice Screw
This vice screw is for the L-shaped shoulder vise used on Scandinavian-style benches. 1-1/8" dia. screw with single-lead Acme threads.
The threaded guide is mortised into the vise shoulder, while the end guide attaches to the vise jaw. 7-1/4" clamping capacity (less wooden shoulder thickness), 13" overall. Mounting screws included.
Made in Canada. Patented.
Veritas Side Rebate Plane
The Veritas Side Rebate Plane is used for cleaning up or trimming sidewalls of rebates, dadoes or grooves to yield a perfect fit with its mate. It has a practical dual-blade configuration, coupled with an ingenious pivoting handle that permits right- or left-hand use to accommodate grain direction.
The thin sole functions much like a skate, allowing use in slots as narrow as 3/16" and to...
Veritas Small Blade Holder
The Veritas Small Blade Holder helps with the difficulty of holding short blades such as those found in most spokeshaves, instrument maker's planes, etc., sharpening them has been difficult.
The Veritas Small Blade Holder solves this effectively and safely by securing the blade using two powerful rare-earth magnets embedded into anodized aluminium and an adjustable stop block. In effect, it...
Veritas Small Crosscut Saw
Used for cutting across or perpendicular to the grain, the 16 tpi crosscut saw blade has teeth filed with alternating bevel angles so it severs rather than tears wood fibers; it tracks better and leaves a smoother finish than a rip-cut blade. The teeth are filed with 15° rake and bevel angles and have 0.003" of set per side.
Veritas Small Plough Plane
This is Veritas' redesigned small plough plane. While it still excels at cutting grooves, rabbets and tongues, it now has the ability to cut decorative beading (beading blades available soon).
Closest in size to the classic Record #044 plane, the preferred size of the old-style plough planes, it has a 6 5/8'' long fence that registers solidly to the workpiece and is through-drilled...
Veritas Small Plough Plane Conversion Kit - Right Hand
For the Veritas Right Handed Plough Plane
Veritas Small Scraping Plane
The Veritas Small Scraping Plane is a great tool for the final smoothing of small, flat surfaces, even highly figured timber, or small areas of difficult grain within a larger surface.
The scraping plane comes into action after the surface has been prepared as well as possible using a finely tuned smoothing plane. What the scraping plane does is to replace the need for sanding prior to applying...
Veritas Small Tapered Reamer
The Veritas small tapered reamer 5mm to 19mm (3/16" to 3/4") is useful to rustic furniture makers for back-tapering holes for through-tenon wedging.
The bit is 85mm overall length with an 8mm hex shank.
Designed for use in an electric drill, these tools may also be used in a traditional brace.
Veritas Special Bench Bolts
Most European benches use a bolt system to fasten leg sets to stretchers. The main advantage is that you can snug the bolts if anything loosens due to changes in humidity.
The solid brass nuts on our bench bolts slide into a pre-drilled hole in the stretcher, and distribute pressure to prevent breakout. A bench can be made very rigid (without complex joinery) by using a wide stretcher, since the...
Veritas Standard Angle Block Plane + PM-V11 Blade
This is the standard angle version of the Veritas low angle block plane.
Preferred for general-purpose work, the 20° bed angle plus the 25° bevel angle on the bevel-up blade result in an effective cutting angle of 45°, the same as found in most bench planes.
A low-profile lever cap results in a plane that fits the hand well, at only 1/8" higher than its low-angle sibling.
Mechanically,...
Veritas Standard Blades for Combination & Small Plough Planes
All blades are made from A2 tool steel. Blades are made in Canada. These blades are suitable for both the Veritas Small Plough Plane and Veritas Combination Plane.
The standard blades are stocked for the right hand versions in 1/8", 3/16", 1/4", 5/16", and 3/8" or 4mm, 5mm, 6mm, 7mm, 8mm and 10mm widths.
Veritas Steel Honing Plate
The Veritas Steel Honing Plate measures 204 x 76 x 9.5mm and weighs 1.1kg.
Precision-ground to flatness tolerance of 0.127mm (0.005").
An excellent substrate for diamond paste (available separately).
Made of dimensionally stable low-carbon steel to retain its flatness. Surface pattern helps capture diamond grit without compromising flatness.
The plates can be glued to a backing board...
Veritas Steel Straightedges
Shop accuracy begins with a benchmark straightedge as a surface reference. These Canadian-made Veritas precision steel straightedges are ground flat over the entire length on both edges, the 24" lengths to within 0.0010" and the 36" length to within 0.0015". All have been stress relieved to remain true under temperature variation. Useful for checking whether surfaces are flat or...
Veritas String Inlay Tool System
Used much like a marking gauge, this inlay tool lets you accurately cut narrow grooves in a workpiece as well as neatly slice fine strings from a sheet of veneer. Its interchangeable blade system lets you quickly swap blades to suit the activity.
The hook-shaped blade is designed to cut grooves. Used in a sweeping push-pull motion, it has outlining spurs on one side of the blade to score the groove...
Veritas Tail Vice
This vise can be used for both types of tail vise - with or without a shoulder. It has guide plates 2" wide by 15" long. The maximum opening is 8" (less the thickness of your wooden jaws).
The single-lead Acme screw is 7/8" in diameter.
Made in Canada. Patented.
Veritas Tapered Reamer Pro
The Veritas Tapered Reamer Pro is designed for use in a hand brace, our pro reamer offers excellent control and good cutting capability for general woodworking. It is particularly useful for tapering through holes where you want to be able to wedge tenons, such as in chair construction.
This reamer has a cast steel alloy body, a separate spring-steel blade, and a pair of blade-adjusting set screws.
When...
Veritas Tapered Snug Plug Cutters
Sometimes when plugging holes, no matter how carefully drilled, the holes finish up slightly oversize for the plug, especially in soft woods. These Veritas cabinet maker's snug plug cutters overcome this by cutting a slightly tapered plug.
The first 3mm of the plug is the diameter stated whilst the remaining length is then flared out at an angle of 3°. Just tap the plug into place until you...
Veritas Thickness Calipers
Primarily used by turners, these Veritas thickness calipers can be fitted into virtually any shape of vase or bowl.
To use, open the caliper by just pulling the legs apart (having the spacing nut between the legs rather than outside them allows this), put in position and then set the spacing nut to the wall thickness. Open calipers, remove and measure tip gap.
The spacing nut can be adjusted...
Veritas Tongue-Cutting Blades for Combination & Small Plough Planes
All blades are made from A2 tool steel. Blades are made in Canada. These blades are suitable for both the Veritas Small Plough Plane and Veritas Combination Plane.
With these tongue cutters, you can now use our small plough plane for tongue-and-groove work. The blades are used in conjunction with our wide-blade conversion kit (see above), creating an interchangeable blade system that enables you...
Veritas Trammel Points
Usable on any rule up to 1/4" thick, these narrow-bodied trammels can be set to reproduce radii as little as 9/16". The removable points score clear lines on any wood, and are also effective on aluminium, brass, bronze and mild steel. With the points removed, the trammel bodies double as square gauges, clamping onto a square to make repetitive angle marking easy. Inspired by an antique trammel...
Veritas Variable Angle Fence for Rebate Planes
This plane fence doesn't limit you to right angles - it allows accurate and consistent planing of any angle from 45° to 135°.
Angles are set using a square or angle gauge, or directly on an angle you wish to match.
The spring-loaded lever, which locks the fence, can be rotated out of the way if necessary.
Through-holes in the 11" long aluminium fence allow the attachment of a wooden...
Veritas Wide Blades for Combination & Small Plough Planes
All blades are made from A2 tool steel. Blades are made in Canada. These blades are suitable for both the Veritas Small Plough Plane and Veritas Combination Plane.
The wide blades are available in 7/16", 1/2", 9/16", 5/8", 11/16" and 3/4" or 12mm, 16mm and 18mm widths. A wide-blade conversion kit (see above) is required for use of all wide blades with the Veritas...
Veritas Wide Router Plane Blades
These high-carbon steel router plane blades will fit the Veritas large and medium router planes, and the the Veritas hinge mortise plane, as well as Stanley #71 router planes (with the height-adjustment nut inverted). The narrow single-piece blades are available in five Imperial sizes
The 1/2" blades have a two-piece design and are available in two styles: straight and spear-point (for final...
Veritas Wile Plane Hammer
Making fine adjustments to plane-blade position is easier with the right tool, and few can compare to the finely made plane hammers of Richard Wile, a hobbyist woodworker from Nova Scotia.
Based on Wile's design, this hammer is machined in our shop to have the same elegant proportions as the original, giving it a weight and balance that feel right in the hand. The small brass head, only 5/8"...
Veritas Wonder Dogs & Pups
Steel post and screw with black oxide finish, solid brass clamp head and handle.
These can pivot in any direction that clamping is required. An easy-adjusting handle provides ample clamping pressure in any position. The dog head has two screw holes, so any tip shape can be cut with a scroll saw and attached for specialized work.
The Wonder Dog post is 6½" and is drilled and tapped...
Veritas Wooden Plane Hardware Kit + PM-V11 Blade
With this kit (and basic woodworking skills) you can build a bevel-down wood-bodied smooth plane with a Norris-style mechanism for easy depth and lateral adjustment.
The kit includes a blade, a Norris-style adjuster with a steel cup to seat it in, plus a knob, tapped insert and cross pin for the lever cap, all made of brass. The lapped PM-V11 blade is 1/8" thick and 1 5/8" wide with...
Accesories for Veritas Dowel & Tenon Cutters
Use the 1/2" drive socket for the 3/8" & 7/16" sizes.
The 5/8" drive socket for the 1/2" dowel.
The four-sided square sockets have a 3/8" square-drive end. The socket adaptor has a 1/4" hex shank.
Dowel Cutters made in Canada. Patented.
Accessories for the Veritas Wood Carver's Vice
Accessories for the Veritas Wood Carver's Vice:
Dog Hole Mount Assembly:
The vice can be side or top mounted through any standard 3/4" dia. dog hole using the auxiliary rod/sleeve/wing-nut assembly, usable on benches from 5/8" to 4" thick.
3 1/2" Mounting Plate:
3-1/2" dia. by 1/2" thick mounting plate with a steel rod.
2" Mounting Plate:
For mounting smaller pieces, such as duck heads or bird...
5 1/2'' Post for Veritas Bench Hold Down
This 5 1/2" Post is for the Veritas Bench Hold Down, for holes where through travel is limited.
At just 5-1/2" long, it provides about 4" of clamping capacity.
Patented.
Blade for the Veritas Small Scraping Plane
Replacement blade for the Veritas Small Scraping Plane 05P2950.
Blade for Veritas Flat & Round Spokeshaves
Replacement PM-V11 blade to fit both the Veritas Flat (05P3373) and Round (05P3374) Spokeshaves.
