Sort By
Per Page
View
Grid
List
Veritas Carvers Screw
Turned from a solid bar of brass, this carver's screw, with its tapered tip and high-profile threads, grips securely and guarantees that remounted pieces are held as securely the third and fourth time as they were the first.
The hex portion clamps securely in a vice while you thread on a blank, or you can use a spanner. The moulded tightening knob has a low-friction brass insert. At 5" long overall,...
Veritas Centre Marker
The Veritas centre marker is used for marking the centre of any square or round piece up to 6" across.
Ideal for marking work removed from a lathe after waste ends have been removed. This accurate centre marker is a precision aluminium die casting with a steel scoring blade.
Easy to use, set the material in the marker, tap it and rotate a quarter turn and tap again, the result is two scoring...
Veritas Chair Doctor Glue
Veritas Chair Doctor glue can penetrate narrow cracks in chairs. I used this on my kitchen chairs which had become decidely wobbly and they are able to withstand my sons rough treatment again - excellent.
If a chair has a loose rung, an injection of Chair Doctor Glue will first swell the rung & then bond it.
The low viscosity lets it soak into the end grain of wood, swell it and then freeze...
Veritas Chamfer Guide for Low-Angle Block Plane
You can convert the Veritas Low-Angle Block Plane (05P22.01) and Standard Block Plane (05P22.30) into chamfer planes in seconds with this cunning guide.
Easy to install - you first set the chamfer width on the guide, then install the guide by unscrewing the front knob of the plane, replacing the toe piece with the chamfer guide and tightening the knob again. It is ready to go.
Adjustable for...
Veritas Combination Plane
Originally created to replace stacks of hollow and round wooden planes, combination planes are defined by their flexibility. However, they are not complex to use and are often faster to set up than a machine for one-off work.
The Veritas combination plane was designed from the ground up to eliminate problems that made the original Record and Stanley planes often frustrating to use. It is precisely...
Veritas Combination Plane Box
This storage box provides a place to keep the assembled plane, the second pair of fence rods and up to two of the blade boxes. Slots in the sides of the box base act as rests for the fence rods, holding the plane upright. The top of the box fits into channels in the box base, locking the plane in position as well as securing other contents.
Made in Canada from Baltic birch plywood, the box is...
Veritas Combination Plane Rabbet Blade - 1 1/16'
Will only work with the Veritas combination plane. 1-1/16" wide PM-V11 rabbeting blade lets you cut rabbets up to 1". 35° bevel angle
Veritas Concave Spokeshave (with PM-V11 blade)
The Veritas Concave spokeshaves have a extremely durable PM-V11 steel alloy blade, seated at 45° to the sole. The thick blade, carefully machined lever cap and blade bed all combine to produce chatterfree cutting in virtually all conditions.
This spokeshave is popular with chair and paddle makers, being the first choice for a wide range of jobs from small spindles to large oars.
The ductile...
Veritas Detail Palm Planes
With a height-adjustable palm rest for better in-hand registration, these miniature planes are easily maneuvered and permit fine, controlled cuts.
The investment-cast steel body has a 45° bed angle and a fixed mouth, and uses a brass retention screw to secure the included 30° bevel A2 tool steel blade (0.06" thick by 3/8" wide). The soles are approximately 1½" long by 5/8" wide and are available...
Veritas Detail Rabbet Plane
The detail rebate plane is primarily useful for small trimming tasks. It is handy for getting into tight spaces, especially cleaning up the bottom of dados or grooves. The plane’s body is ductile cast iron, 75mm long, accurately machined and ground. The sides are flat and square, allowing you to use the plane on its side for trimming tenons. The low 15-degree bed angle combined with the 30-degree...
Veritas Dovetail Markers
For quick, accurate marking of dovetails, this pair of Veritas Dovetail Markers are the best available. With riding ledges on both sides, these 50 x 50mm markers can be flipped over to scribe both slopes of the dovetail.
They are designed so the entire ledge is riding on the reference face, even when marking edge dovetails.
The relieved corners at the join of the body ensure perfect seating....
Veritas Magnetic Guide & Saw
Hand-cut dovetails remain the mark of the skilled cabinetmaker and a feature that buyers look for in high-end furniture. Veritas has developed a guide and saw system that lets amateurs achieve professional results. The system also allows the seasoned expert to produce dovetail joints more quickly and with less effort.
The Veritas Magnetic Dovetail 1:8 Guide, clamps in position and holds the saw...
Veritas Dowel & Tenon Cutters
Obtaining dowels to perfectly match a project or specific species of timber, is to say the least, almost impossible. Not so if you own a Veritas Dowel cutter and have a few timber off-cuts to hand. These cutters can be used two ways. Either use them like a hand-held pencil sharpener, to put accurate tenons on the tips of turnings or on rustic furniture components. Alternatively using a cordless drill,...
Veritas Dowel Formers - Metric
This Veritas dowel former allows you to make dowel pins of whatever length you need. You simply drive an oversized piece of wood through the sharp edged hole of the solid A2 tool steel insert to shear excess material from the dowel. The Veritas 75mm diameter mounting plate has two screw holes for permanent mounting.
Can be used over a 3/4" or 20mm dog hole and is compatible with all inserts. Solid...
Veritas Dowel Maker Master Set
The Veritas® Dowel Maker lets you make perfectly sized dowel from 1/4" to 1" dia. in 1/16" increments, up to 4' long (or longer in the larger diameters) from any wood species you wish. The process uses two blades (both highly wear-resistant A2 tool steel), one for roughing and the other for final sizing. You just rip square stock 1/8" oversize and drive it through the dowel maker using a square...
Veritas Edge-Trimming Planes
Edge-trimming planes are used for final trimming cuts on jointed boards to ensure smooth edges at exactly 90° to the face, and for working end grain. In many instances you will need only one model; the appropriate choice is often based on which of your hands is dominant.
However, neither model is exclusively for left or right handed users, as the planes are in fact complementary. Having both...
Veritas Fluting Blades for Combination Planes
For use with the combination plane, these blades are used to create decorative concave fluting on workpieces. The PM-V11 steel blades are available in 3/16", 1/4", 3/8" and 1/2" flute diameters. Made in Canada.
Veritas Front Vice - Large
This vise has rugged, machined, double guide rods and a single-lead Acme screw.
The large front vise is 10-1/2" × 21" overall with a 1-1/8" dia. screw, and 13" clamping capacity (less the thickness of your wooden jaws). The larger vise has an offset center screw to allow vertical clamping without skewing.
Can be added to an existing bench or built into a new one.
Mounting screws included.
Made...
Veritas Front Vice - Regular
This vise has rugged, machined, double guide rods and a single-lead Acme screw.
The regular front vise is 7" × 14¾" overall with a 7/8" dia. screw and clamping capacity of 8¼" (less the thickness of your wooden jaws).
Can be added to an existing bench or built into a new one.
Mounting screws included.
Made in Canada. Patented.
Veritas Gents Saw - Cross Cut
Sharing the same, advanced materials as the Veritas dovetail and carcass saws, these Gent’s saws have 200mm long high-carbon steel blades just 0.4mm thick with 0.08mm of teeth set per side.
The teeth on the 22tpi crosscut saw have a rake angle of 15°, an included angle of 60° and alternating 15° bevel angles so that they sever rather than tear wood fibres.
Depth of cut is 41mm....
Veritas Gents Saw - Rip Cut
Sharing the same, advanced materials as the Veritas dovetail and carcass saws, these Gent’s saws have 200mm long high-carbon steel blades just 0.4mm thick with 0.08mm of teeth set per side.
The 20tpi ripsaw has teeth with a 14" rake angle and a 60° included angle.
Depth of cut is 41mm. For strength and rigidity, the glass and stainless steel-filled polymer spine is moulded over...
Veritas Grinder Tool Rest
The major weakness of most bench grinders is that the tool rests are virtually useless. It is nearly impossible to find one with a rest that is solid and square.
The Veritas® Grinder Tool Rest can be used with 6" or 8" utility bench grinders and many belt sanders/grinders. It mounts directly to the bench in front of the grinder and can be readily folded out of the way for freehand grinding....
Veritas Grinding Jig
The grinding jig works with any power or hand grinder that has a tool rest.
Put a tool in the jig, slide it against the alignment pin and one clamping thumbscrew to square it, adjust the blade projection for bevel angle, and tighten in place. The tool is now held squarely in the jig at the chosen bevel angle. Slide the jig back and forth across the tool rest and stone face to sharpen the tool....
Veritas Hand Jointer
The Veritas Hand Jointer allows you to accurately joint small parts by hand.
Box-making and modelmaking often require small parts that are too dangerous to run through a power jointer and difficult to joint with a hand plane; balancing a plane on pieces much smaller than its sole can be awkward.
This hand jointing accessory for Veritas medium and large shoulder planes lets you bring the work...
Veritas Hinge Mortice Plane
The Veritas Hinge Mortice plane can accurately cut the recesses for door hinges or strike plates in a fraction of the time it takes to set up a router or chop them out with a chisel. The precision blade depth adjuster ensures an accurate, uniform depth. The ductile cast iron body has been accurately machined and ground flat. The large wooden knobs are positioned to provide comfort and excellent control....
Veritas Inlay Cutter Head for Router Plane
This simple attachment for a lets you score a shallow groove to accept inlaid purfling, banding or stringing, taking advantage of the plane’s fence and depth-adjustment mechanism to precisely control groove position and depth.
The cutter head holds a pair of included single-bevel slicing blades that score crisply defined groove outlines across, with or diagonal to the grain. By using a chisel...
Veritas Inlay String Thicknesser
The critical dimension for string inlay material is thickness. If too thick it won’t fit into the groove; too thin, and it will leave an unsightly gap. This Veritas Inlay String Thicknesser scrapes veneer - or any narrow, thin stock up to 2½" wide - to the exact thickness required.
Instead of a sole that travels on top of the material, it has two skates to elevate the blade from the work surface....
Veritas Jack Rebate Plane + PM-V11 Blade
This Veritas Jack Rebate plane cuts large-scale rebating down to size. The body is 385mm long and the blade extends the full width (57mm) of the body. It is suitable for very large rebates and fielded or bevelled panels. The long sole and substantial mass help ensure accuracy.
The 4.8mm thick bevel-up blade makes right or left-handed corner cuts cleanly and accurately. Adjustable scoring spurs...
.png "Last Ones!")
Veritas Jointer Blade Sharpener
A commercial sharpening service or a sophisticated home grinder is necessary for badly nicked blades. The Veritas Jointer Blade Sharpener is designed to restore blades dulled from normal use, even if they contain minor nicks.
It clamps blades up to 8" wide (including hand-plane blades) for sharpening on PSA-backed abrasives. Just stick the abrasive to a flat surface (plate glass works well),...
Veritas Jointer Fence
Planing a square edge on a board requires a jointer fence, whether you are using an electric jointer or a hand plane.
The Veritas® jointer fence allows you to shoot accurate and consistent square or bevelled edges with most* iron or steel bench planes. The integral rare-earth magnets make it quick and easy to attach or remove the 11" long anodized aluminium fence from either side of all...
Veritas Lapping Grit 90x Silicon Carbide 4oz
Silicon carbide is ideal for flattening oil and water stones or lapping plane bottoms and blades. Just sprinkle the grit on a piece of glass or a steel lapping plate, add a shot of oil or water (as required), and lap the item flat. This fast and easy process lets you keep all of your stones dead flat.
90x is used for most applications.
Using PSA-backed plastic laminate sheets on glass speeds...
Veritas Lapping Kit Set of Five 2 oz Containers - 05M0101
Silicon carbide is ideal for flattening oil and water stones or lapping plane bottoms and blades. Just sprinkle the grit on a piece of glass or a steel lapping plate, add a shot of oil or water (as required), and lap the item flat. This fast and easy process lets you keep all of your stones dead flat.
A set of five 2 oz containers of 90x, 180x, 280x, 400x and 600x and instructions. 90x is used for...
Veritas Large Beading Blades for Combination Planes
These large beading blades are for use only with the combination plane, and are available in 5/16", 3/8", 7/16" and 1/2" bead diameters. All blades cut a 1/16" groove on either side of the blade. Made in Canada.
Veritas Large Journeyman's Mallet
The Veritas Large Journeyman's Mallet has a solid brass head, a walnut handle and a simple, refined profile, making it an elegant and effective mallet.
Designed for work that requires more finesse than power, it can be held by the handle or used with the head cradled in your palm, allowing you to more precisely control the force of blows. The head is attached to the handle with a blind threaded...
Veritas Large Saddle Square
Veritas Large Saddle Square - Many of the people who purchased the small saddle square have asked for a larger version. This version has 1-3/8" x 3-3/8" legs to accommodate a standard 2 x 4 e.g., for stud wall layout. It also has a slot machined through the centre to help lay out stud locations. Simply mark the centres of your studs on top and bottom plate, then place the square so that the...
Veritas Large Shoulder Plane + PM-V11 Blade
The Veritas® large shoulder plane (a specialized rabbet plane) is the latest and largest in our line of shoulder planes. Its size and mass make it perfect for trimming breadboard tenons, adjusting shoulders, or even paring down tenon cheeks. At 8¼" long, 1¼" wide and weighing 3¾ lb, it brings both authority and precision to larger work. The ductile cast iron body is accurately machined and ground...
Veritas Low Angle Spokeshave
The Veritas Spokeshave uses a basic traditional shape, not of the spokeshaves of the last century, but of the century before.
Until about 1900, the vast majority of spokeshaves were low-angle spokeshaves with wooden bodies. The blades were hand forged with upturned tangs that fitted into holes pierced in the body of the shave. Wedged in position, they were adjusted by tapping the ends of the...
Veritas Low-Angle Smoothing Plane + PM-V11 Blade
The Veritas low-angle smooth plane has three key uses. It is used to smooth large surfaces, preferably taking a diagonal cut, partly across and partly along the grain. Similarly, with its generous sides, it is ideal for shooting mitres. Finally, it is excellent for end-grain work. The low cutting angle of 37° minimizes fibre tearing. With a bed angle of 12°, this is a "bevel-up"...
Veritas Magnetic Saw Guides
This anodised aluminium Veritas Magnetic Saw Guide helps keep your saw on the right track and perpendicular to a workpiece. It provides a registration surface about 32mm tall. It is particularly useful when crosscutting tenon shoulders or the edges of a dado, which is where you want your saw to cut straight and true. You can hold the guide onto your workpiece with a hand or secure it with clamps.
The...
Veritas Marking Gauge Replacement Wheel
Replacement wheel for Veritas gauges. Not suitable for the new style micro-adjust marking gauge.
Veritas Marking Gauge Replacement Wheel - (Inside)
Replacement wheel for the Dual Marking gauges. Both the Inside and Outside cutters are required for the Dual Marking gauge.
Veritas Marking Gauge Replacement Wheel - (Outside)
Replacement wheel for the new style Micro-adust and Dual Marking gauges. Both the Inside and Outside cutters are required for the Dual Marking gauge.
Veritas Marking/Mortice Gauge Heads
Though designed for use with their Veritas® Wheel Marking Gauges, these gauge heads are a simple retrofit for any marking gauge with a 5/16" diameter shaft.
Made from carbon steel, the 5/8" diameter wheel cutters will scribe at any point in their circumference and slice rather than tear fibers for clean, accurate cuts. The single-bevel cutters are usable in-line for marking parallel lines, or...
Veritas Medium Router Plane
Slightly larger than the Veritas small router plane, this tool has the advantage of using the same blades as our full-size router plane.
For general use, the blade may be positioned inboard with the sole encircling it for maximum registration on the workpiece, even when approaching from the side or working an edge. This allows it to bridge recesses, providing great stability even on narrow stock....
Veritas Metric Bevel Setters
A sliding bevel is an excellent tool for transferring angles but not for reading them. This bevel setter allows you to set specific angles (from 0° to 60° in 1/2° increments) on a sliding bevel or a workpiece and to read angles already set. Both functions are useful for dovetailing, for machine set-up, for polygon work, or for accurately fitting a piece in a restricted location. Common dovetail...
Veritas Metric Sliding Square
These cabinetmaker's squares are used to lay out or transfer measurements quickly and accurately; you always have an ample reference face against your work without having to flip the square. This also simplifies working in two axes at once (e.g., measuring in 50mm and over 40mm), substantially reducing the chance of error when measuring and marking two dimensions.
The stainless steel blade...
Veritas Micro-Adjust Rod for Wheel Marking Gauges
We offer the micro-adjust rod separately from the gauge body to let you easily upgrade a Veritas standard wheel marking gauge you own with the new adjustment mechanism.
Veritas Miniature Bench Plane
This 1/3 scale version of the Veritas small bevel-up smooth plane is only 3½" long and 13/16" wide.
Fully functional, it has a 5/8" wide A2 blade (0.06" thick) with a 25° bevel angle that, together with the 13° bed angle, provides an effective cutting angle of 38°. The stainless-steel Norris-style adjuster lets you set the blade with precision.
The body is made from investment-cast stainless...