Spare Blade for Veritas Edge-Trimming Plane
Spare Blade for Veritas Edge-Trimming Plane
Replacement blade for the Veritas Edge-Trimming Plane. 1/8" thick, 1 1/4" wide replacement blades in PM-V11 steel work wood up to 1" wide. Made in Canada.
£32.00 inc VAT
Blades for the Veritas Detail Palm PlanesBlades for the Veritas Detail Palm Planes
Blades for the Veritas Detail Palm Planes
Replacement blades for the Veritas detail palm planes. (Convex and double-convex planes use the same blade.)
from £11.50 inc VAT

Replacement Blade for Veritas Cabinetmakers Trimming Plane
Replacement Blade for Veritas Cabinetmakers Trimming Plane
Replacement lapped O1 steel blade for the Veritas Cabinetmaker's Trimming Plane. Hardened to Rc58-60. Made in Canada.
£36.95 inc VAT
Spare Blades for the Veritas Detail Rabbet PlanesSpare Blades for the Veritas Detail Rabbet Planes
Spare Blades for the Veritas Detail Rabbet Planes
The lapped replacement blades for the Veritas detail rabbet planes are made of O1 tool steel.
£12.50 inc VAT

Spare Blades for the Veritas Scrub PlaneSpare Blades for the Veritas Scrub Plane
Spare Blades for the Veritas Scrub Plane
Available in high-carbon steel (Rc58-60) or PM-V11 steel (Rc61-63). The blade edge is ground with a 3" radius, so it takes an aggressive cut.
from £30.00 inc VAT
Veritas Combination Plane Rabbet Blade - 1 1/16'
Veritas Combination Plane Rabbet Blade - 1 1/16'
Will only work with the Veritas combination plane. 1-1/16" wide PM-V11 rabbeting blade lets you cut rabbets up to 1". 35° bevel angle
£22.25 inc VAT

Veritas Dovetail SawVeritas Dovetail Saw
Veritas Dovetail Saw
When we first saw this saw (!) we were a bit dubious but it has quickly grown on us. It is very comfortable. it is very affordable, it cuts well and can be re-sharpened. Not for the purists maybe but beauty is in the eye of the beholder. This is what those clever chaps from Veritas say about this saw.... The Veritas dovetail saw is an innovative blend of tradition and technology. It incorporates...
£86.50 inc VAT
Veritas Fine Cut Dovetail Saw (20tpi)
Veritas Fine Cut Dovetail Saw (20tpi)
The Veritas Fine Cut Dovetail Saw (20tpi) is best for stock of less than half an inch thick, this finer version of the standard Dovetail saw would complement your existing saw armoury. The Veritas dovetail saws are an innovative blend of tradition and technology, incorporating the critical characteristics of a classic fine joinery saw but made using modern production processes and state-of-the-art...
£84.50 inc VAT

Veritas Small Crosscut SawVeritas Small Crosscut Saw
Veritas Small Crosscut Saw
Used for cutting across or perpendicular to the grain, the 16 tpi crosscut saw blade has teeth filed with alternating bevel angles so it severs rather than tears wood fibers; it tracks better and leaves a smoother finish than a rip-cut blade. The teeth are filed with 15° rake and bevel angles and have 0.003" of set per side.
£92.50 inc VAT
Veritas Rip Cut Carcass Saw
Veritas Rip Cut Carcass Saw
The saw has a 275mm (11") long by 0.5mm thick high-carbon steel blade filed for rip cutting at 12tpi. The teeth have a rake angle of 10°, an included angle of 60° for fast and accurate cutting along the line of the grain. The depth of cut is 60mm. The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece...
£89.00 inc VAT

Veritas Crosscut Carcass Saw
Veritas Crosscut Carcass Saw
The saw has a 275mm (11") long by 0.5mm thick high-carbon steel blade filed crosscut at 14tpi. The teeth have a rake angle of 15°, an included angle of 60° with alternate 15° bevels to efficienlty sever wood fibres rather than tear. The depth of cut is 60mm. The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid...
£89.00 inc VAT
Veritas Tenon SawsVeritas Tenon Saws
Veritas Tenon Saws
The unique designs of the Veritas carcass saws and dovetail saws have proved to be extremely popular and Veritas have now introduced two superb tenon saws to complement their range. They combine the best characteristics of this fine classic joinery saw with those of state-of-the-art materials and construction methods. The tooth pattern on the thin high-carbon steel blade provides a good balance...
£130.00 inc VAT

Veritas Dovetail Saw and Magnetic GuideVeritas Dovetail Saw and Magnetic Guide
Back In Stock
Veritas Dovetail Saw and Magnetic Guide
Hand-cut dovetails remain the mark of the skilled cabinetmaker and a feature that buyers look for in high-end furniture. Veritas has developed a guide and saw system that lets amateurs achieve professional results. The system also allows the seasoned expert to produce dovetail joints more quickly and with less effort. The Veritas Magnetic Dovetail 1:8 Guide, clamps in position and holds the saw...
from £32.00 inc VAT
Veritas Flush Cutting SawVeritas Flush Cutting Saw
Back In Stock
Veritas Flush Cutting Saw
Traditionally used for the rapid trimming of plugs and dowels flush with a surface, the Veritas flush cutting saws can be used where you want to cut off a projection without damaging the surrounding or adjoining face. This is possible because the teeth are set one way only The 22 tpi Japanese tooth-pattern blade cuts aggressively (on the pull stroke), but does not mark the surface that it is...
from £25.95 inc VAT

Veritas Gents Saw - Cross CutVeritas Gents Saw - Cross Cut
Veritas Gents Saw - Cross Cut
Sharing the same, advanced materials as the Veritas dovetail and carcass saws, these Gent’s saws have 200mm long high-carbon steel blades just 0.4mm thick with 0.08mm of teeth set per side. The teeth on the 22tpi crosscut saw have a rake angle of 15°, an included angle of 60° and alternating 15° bevel angles so that they sever rather than tear wood fibres. Depth of cut is 41mm....
£67.35 inc VAT
Veritas Gents Saw - Rip CutVeritas Gents Saw - Rip Cut
Veritas Gents Saw - Rip Cut
Sharing the same, advanced materials as the Veritas dovetail and carcass saws, these Gent’s saws have 200mm long high-carbon steel blades just 0.4mm thick with 0.08mm of teeth set per side. The 20tpi ripsaw has teeth with a 14" rake angle and a 60° included angle. Depth of cut is 41mm. For strength and rigidity, the glass and stainless steel-filled polymer spine is moulded over...
£60.75 inc VAT

Veritas Saw File HolderVeritas Saw File Holder
Veritas Saw File Holder
Not only does this Veritas Saw File Holder provide a secondary grip for your saw file, it also helps you control the angle of the file as you sharpen, using the eye's natural ability to judge parallel and level. It has a rotating collar for setting a positive or negative rake angle up to 30°, and a 3" wide protractor to set the fleam (or bevel) angle up to 45° left or right. All you need to...
£46.95 inc VAT
Veritas Magnetic Saw GuidesVeritas Magnetic Saw Guides
Veritas Magnetic Saw Guides
This anodised aluminium Veritas Magnetic Saw Guide helps keep your saw on the right track and perpendicular to a workpiece. It provides a registration surface about 32mm tall. It is particularly useful when crosscutting tenon shoulders or the edges of a dado, which is where you want your saw to cut straight and true. You can hold the guide onto your workpiece with a hand or secure it with clamps. The...
from £37.75 inc VAT

Veritas Saw Guide Clamps
Veritas Saw Guide Clamps
These Veritas Saw Guide Clamps are 50mm capacity clamps are anodised aluminium with solid brass screws and pads. They fit into the T-slot on the underside of the saw guide leaving the upper surface clear. These clamps ensure the guide is secure and firmly held in place resulting in a higher degree of accuracy. Note they can also be used with the magnetic saw guide.
£49.65 inc VAT
Both Veritas Dovetail Saw and Magnetic Guide
Both Veritas Dovetail Saw and Magnetic Guide
Hand-cut dovetails remain the mark of the skilled cabinetmaker and a feature that buyers look for in high-end furniture. Veritas has developed a guide and saw system that lets amateurs achieve professional results. The system also allows the seasoned expert to produce dovetail joints more quickly and with less effort. The Veritas Magnetic Dovetail 1:8 Guide, clamps in position and holds the saw...
£77.85 inc VAT

Veritas PM-V11 Bench ChiselsVeritas PM-V11 Bench Chisels
Back In Stock
Veritas PM-V11 Bench Chisels
Precision made in Veritas' own machine shop, these bench chisels are milled from PM-V11 steel (Rc61-63), an innovative proprietary alloy. This metal's micro-structure makes it extremely durable, so it can withstand the impact of heavy chopping cuts without chipping or deforming as readily as other tool steels, even at bevel angles as low as 20°. Highly wear resistant, the edge typically...

5

from £99.50 inc VAT
Veritas PM-V11 Mortice ChiselsVeritas PM-V11 Mortice Chisels
Last Ones!
Veritas PM-V11 Mortice Chisels
These are substantial mortice chisels. The blades are more than 1/2" thick at the heel of the bevel and are a consistent width from tip to shoulder for accurate registration in a mortice. The chisel sides are slightly relieved to reduce sidewall friction and allow for minor cut corrections. Each has a 25° primary bevel to make deep cuts easier, with a 35° secondary bevel to give them...
from £125.00 inc VAT

Veritas PM-V11 Butt ChiselsVeritas PM-V11 Butt Chisels
Back In Stock
Veritas PM-V11 Butt Chisels
Veritas Butt chisels are made in wider sizes than most chisels, making them efficient for wasting out large areas, such as the mortices for installing butt hinges. They also have shorter blades that some woodworkers find offer improved control. Made from PM-V11 tool steel, the blades taper from shoulder to tip for strength and rigidity, and have parallel sides and true bevel edges for clearance...
from £81.00 inc VAT
Veritas Set of 3 Miniature ChiselsVeritas Set of 3 Miniature Chisels
Veritas Set of 3 Miniature Chisels
This chisel set is the latest addition to the Veritas line of fully functional miniature tools. Made at about 1/3 the scale of our regular bench chisels, each is only about 3-1/4" long overall and weighs less than a third of an ounce. At this scale, the three tools in the set have 3/8", 1/4" and 1/8" wide blades. All permit a delicate touch where fine, controlled cuts are needed. Their...
£48.95 inc VAT

Veritas Square FenceVeritas Square Fence
Veritas Square Fence
A carpenter's square is frequently needed just because of its size. The key disadvantage of such a square (its lack of a supporting fence ledge) can now be eliminated using a Veritas square fence. The 8" (200mm) long anodized aluminum extrusion can be readily attached to either the stock or blade of your square (depending upon intended use) with the two integral brass screws. The face of...
£27.75 inc VAT
Veritas 1 1/2'' Pocket Layout SquareVeritas 1 1/2'' Pocket Layout Square
Veritas 1 1/2'' Pocket Layout Square
The Veritas Pocket Layout Square is machined from solid aluminium extrusion, anodized and laser etched on both sides, this triangular layout square is only 1½" on a side. The 1/2" wide by 1/8" thick base registers solidly against a workpiece and has a 1/8" offset on one edge and 1/4" on the other. Like a standard layout square, it has 1/16" rule graduations as well as angle graduations in 10°...
£12.50 inc VAT

Pencil Tip & 10 Leads for Veritas Trammel Points
Pencil Tip & 10 Leads for Veritas Trammel Points
This pencil tip can replace either of the stainless-steel tips on the Veritas trammel points or the Veritas beam compass. It holds an included 2mm thick, 25mm long HB lead that marks a dark line and holds a bevel edge well. Ten additional pencil leads are included. Made of durable and corrosion-resistant stainless steel with knurled sections to make them easy to remove. Pencil tips measure about...
£17.50 inc VAT
New Veritas Micro-Adjust Wheel Marking GaugeNew Veritas Micro-Adjust Wheel Marking Gauge
New Veritas Micro-Adjust Wheel Marking Gauge
Veritas have refined and redesigned their ever popular wheel marking gauges. This new micro-adjust wheel marking gauge draws on two decades of manufacturing experience, with subtle improvements across the board. The adjustment mechanism built into the stainless-steel rod is intuitive to use. After setting the approximate projection, you can fine-tune the position of the cutter within a range of...
£49.75 inc VAT

Lee Valley Winding SticksLee Valley Winding Sticks
Lee Valley Winding Sticks
Winding sticks are not new; woodworkers have been making them for years from scrap wood and using them to check the flatness of material. Placed at opposite ends of a board, they accentuate any twist (wind), making it easier to identify and correct. With the sticks in place, sight across their top edges. If the edges are parallel, the board is not twisted. Reposition and repeat to check the entire...
£41.55 inc VAT
Veritas 14° Dovetail Saddle Marker (1:4)
New
Veritas 14° Dovetail Saddle Marker (1:4)
This new 14° marker is designed to approximate a 1:4 ratio, for those who prefer this angle when working in thinner stock, as it not only provides stronger material interlock than traditional ratio angles but produces a slightly exaggerated dovetail joint that many find attractive. The long legs ensure accurate registration. Also, much like the Veritas saddle square they are based on, they allow...
£12.75 inc VAT

Veritas Aluminium Straightedges
Veritas Aluminium Straightedges
These anodized aluminium straight edges are 1¾" high and 7/16" wide, and will not rust. The reference edge is machined flat to within 0.003" over the entire length. They are available in three lengths, 24", 38" and 50". The 24" straight edge weighs 1lb, the 38" weighs just under 2lb, and the 50" version weighs 2.5lb.
from £31.45 inc VAT
Veritas Bar GaugeVeritas Bar Gauge
Veritas Bar Gauge
Using a bar gauge lets you directly transfer and compare dimensions without conversion to numbers, reducing the chance of transcription errors. You can even use it to quickly test an assembly for squareness by checking that the diagonals are equal. The base unit consists of two 6" steel rods fixed to aluminium clamp heads. The rods have threaded end holes that accept interchangeable brass...
£79.00 inc VAT

Veritas Bar Gauge 12'' Extension Rods
Veritas Bar Gauge 12'' Extension Rods
This pair of 12" extension rods can be used to extend the reach of the Veritas bar gauge, Veritas beam compass, or Veritas marking and transfer tool. It can also be used with the fence and center kit for the Veritas plunge base for rotary tools or the fence and center kit for compact routers, in order to extend the reach of the fence. The rods have a male thread at one end and a female thread...
£17.45 inc VAT
Veritas Bar Gauge HeadsVeritas Bar Gauge Heads
Back In Stock
Veritas Bar Gauge Heads
Compares measurements e.g. equal diagnosis in drawers. Transfers dimensions without converting into numbers. Can be used for sizing shelves or interior trim on windows. Gauge head openings are 13 x 19mm, rip 6mm slices to make bars (wood not included).
£13.25 inc VAT

Veritas Beam CompassVeritas Beam Compass
Veritas Beam Compass
A beam compass (or trammel) offers longer reach and easier adjustment than an ordinary compass. This updated beam compass is made largely of stainless steel, providing it with improved toughness and rust resistance, not to mention a more modern look. The beams have threaded ends that let you link them together for longer reach. Just the base section of the beam compass deals with circles from...
£89.95 inc VAT

Veritas Beam Compass Heads
Veritas Beam Compass Heads
Using a regular compass for small circles is OK, but for projects involving large circles or arcs, our beam compass heads are ideal. The aluminium heads clamp onto a piece of wood between 5/8" and 3/4" thick, creating a compass whose radius is limited only by the length of stock you have at hand. Each brass clamping knob holds the head securely to the beam using a trapped pin that prevents pivoting...
£66.95 inc VAT
Veritas Carpenter's GaugeVeritas Carpenter's Gauge
Veritas Carpenter's Gauge
Specifically designed to be carried in an apron or pocket, this is both a direct-reading compass and a marking gauge, two things that carpenters frequently need but find hard to carry. It has a rotatable head, which locks vertically for use and horizontally for storage and tip protection. It is direct reading, both for radius and diameter, in inches and centimetres. If you have ever measured a...
£27.65 inc VAT

Veritas Centre MarkerVeritas Centre Marker
Veritas Centre Marker
The Veritas centre marker is used for marking the centre of any square or round piece up to 6" across. Ideal for marking work removed from a lathe after waste ends have been removed. This accurate centre marker is a precision aluminium die casting with a steel scoring blade. Easy to use, set the material in the marker, tap it and rotate a quarter turn and tap again, the result is two scoring...
£26.95 inc VAT
Veritas Dovetail MarkersVeritas Dovetail Markers
Veritas Dovetail Markers
For quick, accurate marking of dovetails, this pair of Veritas Dovetail Markers are the best available. With riding ledges on both sides, these 50 x 50mm markers can be flipped over to scribe both slopes of the dovetail. They are designed so the entire ledge is riding on the reference face, even when marking edge dovetails. The relieved corners at the join of the body ensure perfect seating....
£14.45 inc VAT

Veritas Dovetail Saddle MarkersVeritas Dovetail Saddle Markers
Veritas Dovetail Saddle Markers
These Veritas dovetail saddle markers are precision machined at 1:6 and 1:8 angles, the traditional angles for softwood and hardwood dovetails respectively. The long legs ensure accurate registration. Also, much like the Veritas® Saddle Square™ they are based on, they allow a continuous line to be transferred around the corner, so the straight and angled lines can be scribed at the same...
£14.45 inc VAT
Veritas Miniature Marking GaugesVeritas Miniature Marking Gauges
Back In Stock
Veritas Miniature Marking Gauges
These are fully working versions of the Veritas wheel marking and dual marking gauges, but only one third of the size. Their smaller scale allows greater control and makes these exquisite tools perfect for small marking tasks that require a delicate touch. Each is 57mm long and weighs just over 14g and 21g respectively. Like their full-size counterparts, they cut (not tear) fibres for clear marks...
£35.00 inc VAT

Veritas Dual Marking GaugeVeritas Dual Marking Gauge
Veritas Dual Marking Gauge
The Veritas Dual Marking Gauge has two independently adjustable rods, which will allow you to set two measurements at once, so you can quickly alternate between them when transferring or marking repetitive dimensions. Projection up to 5-3/4" is easy to set, since an internal O-ring keeps light but constant friction on each rod; a thumbscrew firmly locks rods in place. Like other Veritas marking...
£49.50 inc VAT
Veritas Imperial Rule for Sliding Square
Back In Stock
Veritas Imperial Rule for Sliding Square
These Imperial rules for the Veritas sliding squares are interchangeable.
£14.50 inc VAT

Replacement Tip for Veritas Japanese Style Awls
Replacement Tip for Veritas Japanese Style Awls
The replacement tip for the Veritas Japanese-Style Awls is A2 steel hardened to Rc60-62 for toughness.
£7.90 inc VAT
Veritas Large Saddle Square
Veritas Large Saddle Square
Veritas Large Saddle Square - Many of the people who purchased the small saddle square have asked for a larger version. This version has 1-3/8" x 3-3/8" legs to accommodate a standard 2 x 4 e.g., for stud wall layout. It also has a slot machined through the centre to help lay out stud locations. Simply mark the centres of your studs on top and bottom plate, then place the square so that the...
£16.25 inc VAT

Veritas Marking Gauge Replacement Wheel
Veritas Marking Gauge Replacement Wheel
Replacement wheel for Veritas gauges. Not suitable for the new style micro-adjust marking gauge.
£4.25 inc VAT
Veritas Marking Gauge Replacement Wheel - (Inside)
Veritas Marking Gauge Replacement Wheel - (Inside)
Replacement wheel for the Dual Marking gauges. Both the Inside and Outside cutters are required for the Dual Marking gauge.
£4.75 inc VAT
Page: | 1 | 2 | 3 | 4 | 5 | 6 |