Sort By
Per Page
View
Grid
List
Lie-Nielsen Drawer Lock Chisel Pair
Chris Becksvoort came to Lie-Nielsen with this greatly improved design for a traditional tool. This special pair of chisels is indispensable for cutting small mortises in tight places - such as setting a drawer lock into a piece of furniture.
A2 Tool Steel, precision ground. Blade widths are 1/2'' and 1/4''. Blade length is 1'', with a cutting depth of 11/16'' on...
Lie-Nielsen A2 Bevel Edge Chisels
Lie-Nielsen A2 bevel edge chisels - these will hold their edge longer than high carbon chisels and therefore require less frequent sharpening.
The chisel edges are square, parallel along the length, and very narrow so you can get into tight places. The backs are ground flat and finished by hand at 400 grit. The bevel is flat ground at 30°, but a higher secondary bevel (about 35°) is advisable,...
Lie-Nielsen No.62 Low Angle Jack Plane
The Lie-Nielsen No.62 Low Angle Jack Plane. What is not to like? You take the most popular and useful jack plane and bed it at a low angle (12°). This makes the most versatile group of planes even more versatile.
Comes with a 2" (50mm) wide A2 steel blade which is .175" (4.5mm) thick. From the box it has a 25° bevel, but it is worth sticking a secondary bevel of 5° on it if...
Lie-Nielsen No.5 1/2 Jack Plane
A Lie-Nielsen No.5 1/2 Jack Plane. Probably the most popular bench plane, and the one that many woodwork teachers recommend starting out with due to its versatility.
The equivalent of a later type Stanley Bedrock No.605½.
14 3/4" (375mm) long.
2 3/8" (60mm) wide blade. A2 steel.
Iron body, 7lbs (3.15kg).
Lie-Nielsen No.60 1/2 Block Plane
The Lie-Nielsen No. 60½ Block Plane is based on the legendary Stanley No. 60½. This low angle block plane from Lie-Nielsen is a superb little tool for any toolkit — ideal for trimming end grain, chamfering edges, and general fine-tuning.
Adjustable Mouth – The movable front shoe lets you open or close the mouth easily: fine for delicate finishing, wider for more aggressive...
Lie-Nielsen Honing Guide
The Lie-Nielsen version of the side clamping style of honing guide is solidly machined from Stainless Steel, with a Bronze bearing.
Their Honing Guide features removable jaws: it comes with a standard pair of jaws that fit most Lie-Nielsen blades, and additional jaws are available (sold separately) for Chisels 3/16" and under, tall jaws for Mortice Chisels, long jaws for very short blades and...
Lie-Nielsen Bronze Low Angle Block Plane
The Lie-Nielsen small bronze Low Angle Block Planes fit perfectly in the hand and slip easily into the pocket. The 5¼" body holds a 1¼" x 1/8" thick blade. An unobtrusive Stainless Steel adjuster offers blade control of micrometer ease and precision with minimum backlash. The mouth is not adjustable.
The blade in the Low Angle Plane is bedded at 12° for fine cuts...
Lie-Nielsen No.4 1/2 Iron Smoothing Plane
Solidly built, this is the ultimate smoothing plane. It is longer, wider, and heavier than the No. 4, and its extra thick blade eliminates the possibility of chatter.
Comes with a 45° frog as standard. Other frogs are available separately.
10-3/8" (264mm) long.
2-3/8" (60mm) blade. A2 steel.
Iron body 5½lbs (2.5kg).
Lie-Nielsen No.507 Rebating Block Plane
The Lie-Nielsen No 507 Rebating Block Plane is also described as a Lie-Nielsen 60½ Rebating Block Plane (60 1/2R).
This 12° angle rebate block plane is based on an old Sargent block plane (No 507). The plane body is made from unbreakable ductile iron and is ground flat and square to .001". The cap iron is polished bronze. The throat is non adjustable. It is 6¼" long...
Lie-Nielsen No.041 Small Shoulder Plane
This is the smallest of the Lie-Nielsen "Preston style" shoulder planes, 5/8" wide, 5 3/4" long. The blade is 0.140" thick, and the tool weighs 1.35 lbs.
With an adjustable mouth like its larger siblings, this tool is just right for trimming and fitting small tenons, dadoes and rebates.
Replacement Blades are available here
Lie-Nielsen Dovetail Saw with Cherry Handle
Lie-Nielsen believe that their Back Saws are the finest made anywhere. They are an exact copy of a British saw made in 1830. Owning one is like having a piece of woodworking history in your shop.
Since dovetailing is a ripping operation, where the kerf is running with the grain, the Lie-Nielsen Dovetail Saw has its teeth filed to a rip profile, unlike other dovetail saws on the market today. Solid...
Tite-Mark Standard
The Tite-Mark Range is manufactured by Glen Drake Toolworks and distributed by Lie-Nielsen.
The unique micrometer adjustment makes these marking gauges an easy and very accurate tool to use. It has steel shafts with brass body and fixed circular A2 blade hardened to 58-60 Rockwell. The blade retracts safely into a recess in the head.
The Tite-Mark Standard (7" long shaft) is built around a 5/16"...
Lie-Nielsen No.5 Jack Plane
The equivalent of a later type Stanley Bedrock No.605 jack plane.
14" long (355mm)
2" wide blade (50mm)
Iron body 5-1/2lbs (2.5kg)
Vallorbe Triangular Saw Files
To choose the right file, size it to the tooth. Ideally, about half of the cutting surface of the file will be in contact with the tooth -- half of the file will be in the gullet and the other half unused. When you rotate the file to get a fresh edge, it will be uniformly sharp. If you use a smaller file, only some of the new surface will be fresh and the rest dull.
Lie-Nielsen Screwdrivers with Cherry Handles
These Lie-Nielsen screwdrivers are made to fit specific screws on Lie Nielsen tools. They may be useful for other jobs as well. Modelled after gunsmith's screwdrivers with machined tips, they are correctly sized to fit the screw slots, giving you good power and control without slipping. The Chipbreaker and frog adjustment screwdriver are particularly useful.
The blades are hardened 416 Stainless...
Lie-Nielsen No.4 Iron Smoothing Plane
Lie-Nielsen's smoothing planes are precision machined from a manganese bronze casting, or an iron casting. They all come with a beautifully formed handle and knob made from American cherry. They have the Stanley Bedrock style frog which gives a fully machined mating fit between the frog and body. You can move the frog backwards or forwards, allowing the opening or closing of the plane's mouth...
Lie-Nielsen Large Router Plane Open Throat
A router plane is a great tool for working shallow mortices - hinge gains, inlay, doorlocks, trimming tenons and the like. Lie-Nielsen's version is based on an early Stanley 071 model, the Open Throat design offers more visibility in front of the tool, which is especially useful for inlay work. Also, the blade is held solidly in the body in a square broached hole (blades will not fit original...
Lie-Nielsen No.042 Medium Shoulder Plane
A improved version of the now discontinued Record 042. This plane is 3/4" wide and weighs 2.35 lbs. The body is 9¼" long, with a 3/4" x .140" thick blade.
This is an elegant tool for trimming and fitting tenons, dados and rebates.
!!!!
Lie-Nielsen Tapered Dovetail Saw with Cherry Handle
Lie-Nielsen have redesigned their three most popular back saws to feature a slight tapering of the blade from toe to heel. This taper gives you better control over precise cuts. When you reach the gauge line on the front of your stock, the blade is slightly above the line on the back side, which reduces the risk of sawing past your line. In addition, the taper introduces an angled approach to your...
Lie-Nielsen No.1 Iron Smoothing Plane
The Lie-Nielsen No.1 Smoothing Plane in iron. This is based on the famous (and somewhat scarce) Stanley No.1. The size makes it more comparable to a block plane than a smoother but nonetheless this small bench plane is suitable for detail work.
5-1/2" (14cm) long
Blade is 1-3/16" (3cm) x .110" (2.79mm) thick.
Weight is 1.35 lbs. (612 grams)
Lie-Nielsen Cross Peen Hammer
This small hammer is not only great for tacks and brads, but also for making fine blade adjustments on your planes.
Brass Head, 4 oz (115 grams).
Cherry handle
Overall size is 12'' (300mm) long and 4'' (100mm) wide
Lie Nielsen No.66 Iron Beading Plane
This Beading Tool can quickly produce a wide range of decorative profiles without the fuss and fiddle of setting up an electric router.
Derived from an early, generously proportioned Stanley No. 66, it has a Ductile Iron body and Bronze blade clamp. Two Bronze fences are included, one for curved work and one for straight work, and can be adjusted along the slot across the bottom of the tool.
The...
Lie-Nielsen 10 1/4 Rebate Bench Plane
Also known as a Carriage Maker’s or Jack Rebate Plane, this is one of the largest rabbet plane made. Based on the Stanley 10¼, which went out of production in the mid-1940s, we modified the design to fit the Bedrock format. Adjustable side nickers make clean, cross-grain cuts. Both handle and knob can tilt left or right to give better access and control in tight corners.
12-3/4"...
Lie-Nielsen Drawbore Pins
Drawboring is a great way to make a strong mechanical joint. A wooden pin is hammered through slightly offset holes in the two pieces, and pulls the joint together. You use Drawbore Pins to pull the joint together first (with some force and a twisting motion). This eases the edges of the hole, making driving the wood pin easier. You can also disassemble the joint if you want to work on the fit some...
Lie-Nielsen Tapered Tenon Saw with Cherry Handle
Lie-Nielsen have redesigned their three most popular back saws to feature a slight tapering of the blade from toe to heel. This taper gives you better control over precise cuts. When you reach the gauge line on the front of your stock, the blade is slightly above the line on the back side, which reduces the risk of sawing past your line. In addition, the taper introduces an angled approach to your...
Lie-Nielsen Tapered Carcass Saw with Cherry Handle
This is the tapered version of the ever popular carcass saw. The taper gives you better control over precise cuts. When you reach the gauge line on the front of your stock, the blade is slightly above the line on the back side, which reduces the risk of sawing past your line.
The tapered saw is very similar to the standard carcass saw in size, but has a thinner plate of .015". It tapers 1/4"...
Lie-Nielsen 16'' Tenon Saw with Cherry Handle
A Tenon Saw is a large backsaw used for making deep, accurate cuts in furniture joinery. It should make straight, fast cuts without binding. Based on a classic Henry Disston model from the early 20th century, our Tenon Saws have Cherry handles, Brass fittings, and stout ¾'' x ¼''' milled Brass backs. These saws are solid, well balanced and smooth cutting. Filed rip...
Lie-Nielsen Carcass Saw with Cherry Handle
The Carcass Saw is used for precise cuts across the grain, cutting tenon shoulders, and defining the edges of a dado.
It has 14 points per inch, filed crosscut, for cutting quickly, yet accurately and smoothly.
Blade is .020" (.5mm) thick, with a .003" (.076mm) set.
Overall length, including handle, is 19" (48.26cm), with an overall height of 4-7/8" (12.38cm).
Usable blade dimensions are 14"...
Lie-Nielsen No.3 Iron Smoothing Plane
Lie-Nielsen's smoothing planes are precision machined from an iron casting. Comes with a beautifully formed handle and knob made from American cherry. They have the Stanley Bedrock style frog which gives a fully machined mating fit between the frog and body. You can move the frog backwards or forwards, allowing the opening or closing of the plane's mouth without having to remove the lever cap...
Lie-Nielsen Set of 5 Bevel Edge Chisels
The ever popular Lie-Nielsen A2 bevel edge chisels as a set. The most popular 5 sizes are included -
1/4", 3/8", 1/2", 3/4", 1".
This does not include a tool roll.
Boggs Concave Spokeshave
The Boggs Concave Spokeshave is a collaboration between Kentucky Master Chair Maker Brian Boggs and Lie-Nielsen Toolworks. A 2-5/8" diameter sole makes this tool the right choice for working chair spindles and other round parts.
Weight 8 oz. Body is 9-5/8" long, A-2 blade 1-1/8" x 1/8" thick, Bronze body and cap. Hickory handles.
Lie Nielsen Carbide Burnisher
Creating a burr on a scraper requires a hard, highly polished surface.
The Lie Nielsen Carbide Burnishers have a 4" polished solid Carbide shank held in a Cherry handle. A flared Brass bolster protects your fingers while burnishing.
Lie Nielsen No.66 Replacement Blades for L-N66
Seven hardened, double-ended blades will make 14 standard shapes. The blades will fit antique Stanleys as well, for those who have or acquire one without blades. Made from A2 Tool Steel, 5/8" (1.58cm) wide.
The blade profiles include:
1/16", 5/64", 1/8", 5/32", 3/16", and 1/4" Single Beads
3/32" and 1/8" Fluting
1/8" Double Reed
1/16" and 5/64" Triple Reeds
1/16" Quadruple Reed
3/32" Double Concave
3/32"...
Lie-Nielsen Scrub Plane
This plane is based on the Stanley 40 1/2 and is designed to remove large quantities of wood quickly e.g taking rough-sawn boards down to size, before finishing with a Jack Plane and a Smoothing Plane.
It is also useful for shaping irregular objects or creating an interesting finished surface.
The Lie Nielsen Scrub Plane has a cast Iron body, 10¼" long. The blade is massive to eliminate...
Depth Stop for Lie-Nielsen 271 Small Router Planes
Brass depth stop makes it easy to cut predetermined depth repeatedly.
Blades for Lie-Nielsen 271 Small Router
For use in the Lie-Nielsen No. 271 Small Router Planes. Made from O1 Tool Steel.
The Small Router Plane comes with a 1/4" wide square tip blade (this blade).
There are three specialty blades designed for inlay work are also available:
1/4" Pointed Tip
3/32" Pointed Tip
3/32" Square Tip (this one)
Lie-Nielsen 50 Degree Frog
If you prefer a higher angle for your plane blade you can either fit a 50 degree (York Pitch) or a 55 degree (Mid Pitch) frog.
Most planes have their blades at an angle of 45°, known as common pitch. But the famous English Smoothers like Norris are usually 50° (York Pitch) or 55° (Middle Pitch). The higher pitches make smoothing difficult wood easier.
These 50 degree frogs will fit Lie-Nielsen...
Lie-Nielsen 55 Degree Frog
If you prefer a higher angle for your plane blade you can either fit a 50 degree (York Pitch) or a 55 degree (Mid Pitch) frog.
Most planes have their blades at an angle of 45°, known as common pitch. But the famous English Smoothers like Norris are usually 50° (York Pitch) or 55° (Middle Pitch).
The higher pitches make smoothing difficult wood easier.
Lie-Nielsen 7 Tool Chisel Roll
7 pocket leather tool roll, Brass fittings. Beautifully made in Maine, USA.
Lie-Nielsen 9 Tool Chisel Roll
9 pocket leather tool roll, Brass fittings. Beautifully made in Maine, USA.
Lie-Nielsen 12 Tool Chisel Roll
12 pocket leather tool roll, Brass fittings. Beautifully made in Maine, USA.
Lie-Nielsen Boggs Spokeshave
The original Boggs Spokeshave is hefty and solid, weighing 12 oz. Designed for fine, precise shaping in all woods. Available with either a flat or curved sole.
Body is 10" long with a 1" wide flat sole.
The sole of the Curved Spokeshave has a gentle, 5" radius for working inside curves.
2" wide x 1/8" thick A2 blade.
Bronze body and cap.
Hickory handles.
Weight is 12 oz.
Lie-Nielsen Small Router Plane Open Throat
Loosely based on the Stanley No. 271, these small Router Planes are perfect for shallow mortise and small relief work. The compact design makes it easy to guide along narrow edges and fit into tight spaces.
The Closed Throat design gives more support in front of the blade, making it ideal for working on the edges of boards or cleaning out the end of a stopped groove in a rail or stile.
Lie-Nielsen...
Lie-Nielsen Chisel Handles
Lie-Nielsen chisel handles are made from Maine-harvested Hornbeam and can be used with any of the Lie-Nielsen chisels.
The standard handle is recommended for all but the largest chisels.
Long chisel handles are 4" longer than the standard handles. Excellent for paring.
The Mortise chisel handles are slightly larger in diameter and length than the standard chisel handle, the Mortise Chisel Handle...
Lie-Nielsen Chisel Plane
The Lie-Nielsen Chisel Plane is the perfect little tool (6½" x 1¾") for removing glue and trimming dowel plugs. It is very useful for working into corners and to the ends of rebates.
The heavy 3/16" thick blade is set at 12 degrees. You adjust the depth of the cut by a nicely machined knurled knob. American cherry handle.
!!!!
Lie-Nielsen Corner Chisel 3/8''
Producing square mortises is exacting work. The Corner Chisel, used after the mortise has been roughed out by hand or with a slot mortiser—which produces round edged mortises—helps square corners easily and precisely.
Made from A2 Tool Steel, hardened to RC 60-62 and ground razor sharp. Beveled at 30º. Comes with a Hickory handle. Overall length is approximately 10".
Currently...
Lie-Nielsen Countersink with Cherry Handle
Cherry handle with solid brass ferrule.
3 flute, 82° countersink.
Please note that wood handles have natural figure and colour variations in the wood grain and may not match the photo.
Lie-Nielsen Dowel Plates
If you want to make exact-sized dowels from any wood you choose, a Lie-Nielsen Dowel Plate is the best tool.
It's also handy to get a precise tenon on chair spindles. The Lie Nielsen plates are 1/4" x 5-5/8" x 1½" surface ground A2 tool steel. The holes are machined with 6-degree clearance taper on the underside, the holes are straight for the first .025"; so this tool can be sharpened many times...
