Active Sales

3 Japanese bevel edge bench chisels [Pre-owned]

These appear to be by the same maker but we cannot quite read the makers stamp clearly enough to get an exact match. Single fluted, with machine made striking hoops to red oak handles. Widths 6mm, 15mm and 30mm Nice addition or introduction to Japanese bench chisels at a very good price.

£75.00 inc VAT

Lie-Nielsen Toolworks - No.102 White Bronze Block Plane [As New]

This plane is very sought after and falls into the collectors category for many. A fully functional plane of course bit this was made in limited numbers by Lie-Nielsen Toolworks. Thsi particular plane has been in its box since first purchased. You will see that we have taken it out of the box to photograph it. It is mint condition. The box has a few minor tears but is in G++ condition.. This...

£475.00 inc VAT

Lie-Nielsen Toolworks - No.3 Iron Smoothing Plane [As New]

Mint in the box, iron bodied Lie-Nielsen Toolworks No.3 smoothing plane (box dated 2019)

£375.00 inc VAT

A Stanley No.6C (Corrugated sole) [Vintage]

Needs a darn good clean up. This plane has a corrugated sole to assist movement over resinous wood. We do not see too many of these. Will clean to G++ 18 inches long, 2 3/8 inch wide, weighs in at just under 8 lbs. Made between 1898 and 1970 - we think this may be pre-2nd WW.

£100.00 inc VAT

An Ebony & Brass Mortise Gauge [Vintage]

An Ebony & Brass Mortise Gauge [Vintage]

These are so well made, really heavy with thick brass plate and escutcheon. The 2 pins are needle sharp so watch out! These are typically found in British cabinetmakers workshops of yesteryear. The screw adjuster works well but these are considered keepsake collectables these days. We have not done anything to this one and it will polish up beautifully if you wish to do so. ...

£45.00 inc VAT

Japanese Mortise Chisel for fine work [Pre-owned]

6mm wide mortise chisel. The makers mark is difficult to read but this appears to be quality chisel with litte wear. Single hollow flute. Machine made striking hoop on red oak handle.

£30.00 inc VAT

Boxwood - Medium Size diameter from the tree [Clearance]

Boxwood - Medium Size diameter from the tree [Clearance]

A medium diameter length of boxwood in the round (from the tree). This has been sitting in a cabinet makers shop for 20 plus years so is in stable, dry condition. It needs to be used and this is your opportunity to do so for creating handles, infils for small plane making, inlay or other use. Study the photographs carefully as the measure/rule in the photos will give you a good guide as to...

£30.00 inc VAT

Stanley No.104 Pressed Steel Smoothing Plane [Vintage]

Referencing page 119 of THE STANLEY PLANE by ALVIN SELLENS (The Early American Industries Association 1975) this plane was advertised as being lightweight , easy to use and were listed as being in demand for manual training classes. Rosewood handle and front knob (in very good condition) Endwise iron adjustment is accomplished on these planes by operation of a 2 pronged lever mounted behind the...

£100.00 (VAT exempt)

2 Fine Sorby Paring Gouges [Vintage]

These are beautiful shallow paring gouges of vintage quality by I.Sorby Are the handles original - maybe not but they are both dark rosewood and gorgeous. Not made like this anymore! 1 inch and 5/8 inch wide 14 inch overall.

£75.00 inc VAT

A Leatherworkers strapped hammer [Pre-owned]

This has been cleaned and polished so looks almost new apart from one small stain to the strap. Nicely made. The round face is about 3/4" (19mm) in diameter. No makers mark.

£25.00 inc VAT

A Repaired Record 3 in 1 Plane - The 311 [Pre-owned]

The Record 311 Shoulder plane Bullnose Plane Chisel Plane This is a matched plane (that is to say that all original parts so there is perfect matching of parts). NOTE - THERE IS A GOOD REPAIR BY WAY OF BRAZING TO ONE OF THE LUGS (the starboard side) THAT HOLDS THE LEVER CAP - SEE PHOTO The plane is fully functional but aesthetically compromised hence the price. ...

£65.00 inc VAT

A Preston Bullnose Plane [Pre-owned]

A good example of this popular bullnose plane with good life left in the iron.

£45.00 inc VAT

Stanley No.93 Shoulder Plane [Pre-owned]

Stanley No.93 Shoulder Plane [Pre-owned]

In near perfect condition, this plane has not done any work. It is a recent model. Full iron. Stanley, Made in England. This plane is commonly used for trimming tenons, shoulders, and cutting or cleaning up rebates (rabbets). Made in Sheffield, England, often seen as a reliable alternative to the US-made versions, with production spanning several decades from the mid-20th century.

£75.00 inc VAT

Blacksmiths Rounding Hammer [Pre-owned]

A lovely blacksmiths rounding hammer with 1 inch square and 1 inch diameter round faces. There is something very pleasing about this hammer with its simple form and 10'' oak handle.

£30.00 inc VAT

Lie Nielsen Toolworks - No.610 Low Angle Jack Rebate Plane [Pre-owned]

Lie Nielsen Toolworks - No.610 Low Angle Jack Rebate Plane [Pre-owned]

This plane has been discontinued from the Lie Nielsen tool range for several years now. This particular example has been used but well looked after. It is in G++ condition with an almost full Lie-Nielsen iron. No box. The 610 is a specialty tool for furniture makers. Think it as a rebating version of Lie-Nielsen's best selling No.62 low angle jack plane. It is very useful for making...

£485.00 inc VAT

Veritas Mortise Chisel [Clearance, As New]

Veritas Mortise Chisel [Clearance, As New]

Now discontinued from the Veritas range. We are not sure why as these were popular despite their cost. PMV-11 steel. 1/4'' wide. Unused old stock.

£75.00 inc VAT

Oval handled Mortise Chisel [Pre-owned]

Heavy duty vintage oak oval handled wide mortise chisel. Only Ray Iles makes these now to this classic design and his are a lot of money (fully warranted). A lovely tool that needs to work.

£35.00 inc VAT

Oval Handled Mortise Chisel 5/16'' [Pre-owned]

A traditional mortise chisel 5/16 inch wide made in Sheffield England. Lovely beech oval handle with leather washer to bolster. Great value.

£36.00 inc VAT

Lie-Nielsen Toolworks - No.212 small scraping plane [Pre-owned]

This bronze bodied small scraping plane has been out of production for a good few years at Lie-Nielsen Toolworks. The iron version is available from Classic Hand Tools. 'This unusual plane is based on the now scarce Stanley No.212. The almost perpendicular blade makes it ideal for small scraping jobs, producing shavings like the finest lace leaving smooth surfaces with crisp edges. The...

£325.00 inc VAT

Auriou - Curved Cabinetmakers Rasp [Pre-owned]

Useful for sshaping and smoothing shallow hollow forms such as bowls, chairseats etc. Auriou rasps are considered by many fine authorities (peole who actually use them in their work) as the best. Thsi rasp is 11 inches long plus a 5 inch handle. Stitched on the underside only, it tapers to a tip with a max width of 1 1/2 inches (38mm) This rasp is slightly different to the standard range (which...

£75.00 inc VAT

Woodpeckers In-Dexable Centre Finder with 150mm Rule [Pre-owned]

Woodpeckers have discontinued this very useful tool so here you go, your last chance to buy one from us. To find the middle of any round or square stock this Woodpeckers Centering Head holds the blade at a 45° angle relative to machined 90° surfaces. Marking the two diagonals of a square locates centre. It’s even easier to find the centre of a circle…just hold the Centering...

£145.00 inc VAT

Woodpeckers - Woodworking Rule Protractor Head - Metric [Pre-owned]

Woodpeckers are discontinuing this tool. We just have the one left. The Woodpeckers Protractor Head is a precision-machined, aluminum tool designed to convert Woodpeckers Woodworking Rules into versatile, adjustable T-squares capable of setting any angle from 0° to 180°. It is designed for high-accuracy angle layout and measurement in woodworking, featuring laser-engraved scales and a smooth,...

£150.00 inc VAT

Woodpeckers Auto Line Precision Drill Guide [Pre-owned]

The Woodpeckers Auto-Line Drill Guide keeps your drill bit perfectly perpendicular when drilling. It also has a sliding base and fence system that makes it simple to keep your hole locations true. The Woodpeckers Auto-Line Drill Guide has a high quality 12.7mm (1/2") chuck supported by a pair of sealed ball bearings. The shaft has a standard quick-release fitting that will fit any cordless...

£265.00 inc VAT

Screw Stemmed beech filester plane with brass fittings [Pre-owned]

EMIR - MADE IN LONDON This was almost hidden in the depths of a large tool chest and was quite mucky when we released it from its hiding place. We have cleaned away some of the grubbiness which was mainly dirt and shavings and underneath it all is a very nice examle of this plane. The screw stems are near perfect.The brass fittings are original and undamaged. Original wedge and iron. This plane...

£65.00 inc VAT

11 Medium Cut English Made Rifflers [Vintage]

These are useful well shaped rifflers for detailing work on wood and ssoft stone. Anout 7 inches long. Hours of fun to be had with these. Many are marked Stubs England. Stubs is a renowned maker of quality tools from Warrington England.

£45.00 inc VAT

Lie-Nielsen Toolworks - 2 3/8 inch wide replacement frog [Pre-owned]

Ribbit ribbit ribbit... What is Kermit's favourite music......answer at end... This Lie-Nielsen replacement frog is at the standard angle of 45 degrees and is for a LN No. 4 1/2, 5 1/2, 6 or 7 plane only. Supplied with a branded Lie-Nielsen plane sock. It has a very minor scratches but appears unused. Selling for about £105 on our main site. (oh yes.....Kermit's favourite...

£75.00 inc VAT

8 fine cut English made rifflers for wood or stone [Pre-owned]

These are useful well shaped rifflers for detailing work on wood and soft stone. About 5 1/2 inches long witha fine cut. Hours of fun to be had with these. Many are marked Stubs England. Stubs is a renowned maker of quality tools from Warrington England.

£40.00 inc VAT

Marples - Rosewood & Brass Panel Gauge [Pre-owned]

Litte used, this 30 inch panel gauge is made from rosewood and brass. Made by Marples of Sheffield, England. This Panel Gauge allows lines to be gauged past the centre of a 56” wide panel. The stem is 30” long and the head 9” wide with a brass wear strip fitted inside a rebate which rests on the edge of the panel to be gauged. The stem has a steel marking pin, plus the facility...

£36.00 inc VAT

Lovely Stanley No.5 [Pre-owned]

A very nice Stanley Bailey No.5 jack plane with lovely rosewood handles. This plane has been used bt there is plenty of life left in the blade. It has been extremely well looked after.

£85.00 inc VAT

Craftsman made marking knife with attractive curly maple handle [Pre-owned]

Craftsman made marking knife with attractive curly maple handle [Pre-owned]

A nicely made marking knife with blade. inches overall. The handle is made from curly maple and is nicely figured. Blue Spruce "esque" in appearance but this is a very nice craftsman made version.

£25.00 inc VAT

5 Henry Taylor Straight Carving Gouges [New, Clearance]

Last 2 sets!

£75.00 inc VAT

Stanley 55 Combination Plane [Vintage]

A very good example of this classic plane. More often than not, these planes are missing things such as the nicker irons, the slitter cutter, cam rest, short rods and the like which can be irritating to say the least. No such woriies here as this Stanley 55 Universal Plane is complete including 4 boxes of standard cutters and an instruction booklet. We see alot of Stanley 45 & 55's...

£295.00 inc VAT

Stanley No.67 Shave [Vintage]

These are quite difficult to find these days. A nice example of the Stanley 67 spokeshave which has detachable rosewood handles that can be moved to a 90 degree setting by use of pre-drilled holes. Good original Stanley Sweetheart iron remains.

£60.00 inc VAT

Record No.8 Jointer [Pre-owned]

A well looked after No.8 Record jointer plane. 2 5/8” wide original Record blade (plenty of life left) 24” long and weighing in nearly 5 kgs Good stained beech handles. Clean mouth.

£145.00 inc VAT

Record No.7 Jointer Plane [Pre-owned]

Record No.7 jointer plane in excellent condition, original full 2 3/8 inch wide iron Stained beech handles. The plane presents very well and just needs a bit if a final clean. There is staining to the cap iron and blade as you can observe but nowhere the cutting/holding edges. In good order. This weighs in nearly 3.5kgs so work those muscles!

£135.00 inc VAT

Preston Bullnose Plane [Vintage]

An excellent bullnose plane with good iron by Preston. The mouth is square. 1 1/8 inch wide. 5 1/4 inches overall. The sole is 3 3/4 inches long. Body has cosmetic blemishes comensurate with age. This will be a good value addition to your tool box.

£52.00 inc VAT

4 Beech Spokeshaves [Vintage]

4 nice beech sopkeshaves with good blades. Cutting edges of 1, 1 3/4, 2 1.4 & 2 3/4 inches. The 1, 1 3/4 and 2 1/4 inch bladed shaves have quite tight mouth openings whereas the largest shave has done more work and the mouth is more open due to wear but it is perfectly usuable. The 1 inch blade spokeshave has a brass wear strip. Quite a cute collection.

£34.00 inc VAT

4 Diamic Henry Taylor Turning Gouges [Pre-owned]

4 Diamic Henry Taylor Turning Gouges [Pre-owned]

4 Henry Taylor DIAMIC brand turning tools which have seen very little use (one cracked ferule). HS1 - Superflute Gouge: A high-performance, general-purpose gouge. Often used for bowl turning and considered more versatile than traditional bowl gouges. 1/2 inch (13mm) cutting edge and 5/8 inch (16mm) bar.The original Superflute HS1, designed in 1978 by Roy Child, has sold in thousands all over the...

£210.00 inc VAT

Gifkins Standard Dovetail Jig [Pre-owned, As new]

Gifkins Standard Dovetail Jig [Pre-owned, As new]

Fancy making some boxes without getting too bogged down with marking, measuring, sawing, chiselling and swearing? This is a commission sale of this popular and easy to use Dovetail jig which you can learn all about here: Gifkins A10 Dovetail Jig This is available brand new for £345 as you can see, but this is an unused item from one of our customers and is a commission sale. As new, unused. This...

£255.00 (VAT exempt)

Shapton Kuromaku Professional Sharpening Stone 30,000 grit

Grab yourself a sharpening bargain!

Was £295.00 Now £225.00 inc VAT

Norris No.20E Shoulder Plane [Rare, Vintage]

Norris No.20E Shoulder Plane [Rare, Vintage]

This plane has been professionally restored although you wouldn't know this unless we told you as the restoration is perfectly done. The steel soled mouth is tight and true. Gunmetal body with lovely ebony infil and wedge. A very nice shoulder plane which bears the dings and marks of use. There is little left of the original Norris blade (clearly stamped with Norris London) hence the...

£295.00 inc VAT

Norris No.13 Smoothing Plane [Vintage]

Steel soled Norris smoothing plane with pinned parallel patent metal sides and attractive rosewood infill. Alex Mathieson & Son iron ( 1 ½” remaining at least) and matching cap iron. The lever cap is stamped Norris London. This was once owned by an A Kirkland, whose name is on the rosewood, AK initials on the plane bed and quite discreetly dotted on one of the steel sides. The...

£325.00 (VAT exempt)

Lie Nielsen Toolworks – Replacement blade for a No.2 Plane [Clearance, As New]

Original rust proof packaging – as new. 1 5/8” wide. This is for a Lie-Nielsen No.2 smoothing plane.

£50.00 inc VAT

Stanley 45 Combination Plane in Original Metal Box [Pre-owned]

This is a Stanley 45 Universal Plane It is in very good working order and has its spur cutters and original fittings. Unused set of 21 boxed cutters to include. 6 beading cutters. Two match cutters. One sash cutter. 11 plow and dado cutters. One fillester cutter (please ignore the wooden rods in the photo, they are to help with packing in the metal box only!) The plane is in very...

£145.00 inc VAT

Auriou Rasp-stitchers Hammer [Rare, Vintage]

Auriou Rasp-stitchers Hammer [Rare, Vintage]

RARE INDEED

£165.00 inc VAT

Henry Taylor Sheffield Fishtail Carving Gouges – Series 11 – 5 widths [New, Clearance]

Clearance stock, From the "Professional" range of Henry Taylor carving tools. These fishtail gouges have a 4¾" (120mm) blade with a ground inner surface and a charcoal black non-reflective finish on the outer surface. Fitted with an octagonal beech handle and brass ferrules. Professional grade Sheffield made fishtail gouges series 11 – which is a tight curve. These...

£120.00 inc VAT

Brand

Price

Additional Filters

Sort By

Per Page

View