Lee Valley 3/4'' Dog Hole BushingsLee Valley 3/4'' Dog Hole Bushings
Back In Stock
Lee Valley 3/4'' Dog Hole Bushings
These 3/4'' hardened steel bushings help you make an accurate dog-hole drilling guide using any 1 1/2'' thick board. Knurling on the bushing provides a mechanical lock when installed in an appropriately sized hole (1'' for the 3/4'' bushing), and a projecting rim ensures that it rests perpendicular to the jig's surface. Made in Canada.
£10.00 inc VAT
Veritas Bench Dogs & Pups
Veritas Bench Dogs & Pups
These are made from solid brass rod. Sold in pairs. The crosshatching and 2° slope on the face help to hold wood securely, pulling it down onto the bench's surface. A side spring slides cleanly and holds it in position. The dogs are 110mm (4.3/8") long, the pups 60mm (2.3/8"). Both work well in combination with Veritas Wonder Dog and Wonder Pup Clamps. For 19mm (3/4")...
from £25.00 inc VAT

Veritas Planing StopVeritas Planing Stop
Veritas Planing Stop
These low-profile work stops present a broad bearing surface. Particularly useful with thin or narrow workpieces, each 1 1/4" wide anodized aluminum rail projects just 0.22" above the bench top, allowing materials as thin as 1/4" to be worked or planed without obstruction. It also provides a reliable registration surface for materials too narrow to span two adjacent bench dogs. The...
£25.50 inc VAT
Muzzles for Veritas Bench Dogs & PupsMuzzles for Veritas Bench Dogs & Pups
Muzzles for Veritas Bench Dogs & Pups
For clamping a finished piece without marking it, the slip-resistant muzzles slide over the Bench Dogs (or Bench Pups) to give you a non-marring surface. They have a hard, spring-grip, plastic body with six face ribs. Available in two sizes: 1¼" long for Bench Dogs or 3/4" long for Bench Pups. Sold in pairs.
from £2.25 inc VAT

Veritas Wonder Dogs & PupsVeritas Wonder Dogs & Pups
Veritas Wonder Dogs & Pups
Steel post and screw with black oxide finish, solid brass clamp head and handle. These can pivot in any direction that clamping is required. An easy-adjusting handle provides ample clamping pressure in any position. The dog head has two screw holes, so any tip shape can be cut with a scroll saw and attached for specialized work. The Wonder Dog post is 6½" and is drilled and tapped...
from £35.00 inc VAT
Veritas Quick-Release Wonder DogVeritas Quick-Release Wonder Dog
Veritas Quick-Release Wonder Dog
This version of the Wonder Dog has a fast-acting cam mechanism to speed up adjustments. You just slide the head against the workpiece, then throw the lever to apply clamping force. Curved and irregular shapes can also be clamped; two screw holes in the brass dog head let you attach a custom face of any shape, giving good control without marring work. The low-profile head and clamp body are 5/8"...
£66.50 inc VAT

Veritas Bench Hold DownVeritas Bench Hold Down
Veritas Bench Hold Down
The Veritas hold-down can clamp workpieces to a bench or anywhere a 3/4" hole can be drilled. Exceptionally high clamping forces can be obtained with this hold-down for two reasons. First, with the arm free to pivot independently, all levered forces are exerted downward, without any losses due to horizontal slippage from the canting action of the hold-down post. Second, the fine barb-shaped grooves...
£115.00 inc VAT
5 1/2'' Post for Veritas Bench Hold Down
5 1/2'' Post for Veritas Bench Hold Down
This 5 1/2" Post is for the Veritas Bench Hold Down, for holes where through travel is limited. At just 5-1/2" long, it provides about 4" of clamping capacity. Patented.
£7.75 inc VAT

Veritas 3/4'' Surface ClampVeritas 3/4'' Surface Clamp
Back In Stock
Veritas 3/4'' Surface Clamp
Hold down, bench clamp or surface clamp - the functions are the same just the name changes. True to form Veritas have taken an ordinary thing and made it much, much better - as well as a thing of beauty in brass and black satin. These fast acting surface clamps can be used anywhere you can drill a 19mm diameter hole. The post has a wedging mechanism which anchors it firmly (horizontally or vertically)...
£69.50 inc VAT
Veritas Vice Handle
Veritas Vice Handle
A wooden handle from Veritas that fits both their Tail Vice Screw and their Front Vices. Handle length 310mm and diameter of 30mm
£9.65 inc VAT

Veritas Front Vice - Regular
Veritas Front Vice - Regular
This vise has rugged, machined, double guide rods and a single-lead Acme screw. The regular front vise is 7" × 14¾" overall with a 7/8" dia. screw and clamping capacity of 8¼" (less the thickness of your wooden jaws). Can be added to an existing bench or built into a new one. Mounting screws included. Made in Canada. Patented.
£89.00 inc VAT
Veritas Front Vice - Large
Veritas Front Vice - Large
This vise has rugged, machined, double guide rods and a single-lead Acme screw. The large front vise is 10-1/2" × 21" overall with a 1-1/8" dia. screw, and 13" clamping capacity (less the thickness of your wooden jaws). The larger vise has an offset center screw to allow vertical clamping without skewing. Can be added to an existing bench or built into a new one. Mounting screws included. Made...
£125.00 inc VAT

Veritas Quick-Release Front ViceVeritas Quick-Release Front Vice
Veritas Quick-Release Front Vice
Using the same quick-release mechanism as our tail vise, our front vise has a simple on-off cam lever to engage or disengage the Acme-threaded screw, allowing it to apply up to 400lb of force in either clamping or spreading applications. The screw mechanism provides 12¼" of overall travel (less the thickness of your wooden jaw and bench apron). Tight body tolerances result in minimal jaw sag,...
£430.00 inc VAT
Veritas Quick-Release Sliding Tail ViceVeritas Quick-Release Sliding Tail Vice
Veritas Quick-Release Sliding Tail Vice
Installing a tail vise is notoriously difficult, usually requiring a section of workbench to be cut away and rebuilt around a complicated vise mechanism. Not so with this one. It can be quickly incorporated into a new bench construction or easily retrofitted to an existing bench without major surgery. The end plates are symmetrical, so you can install the T-handle and quick-release lever in a...
£420.00 inc VAT

Veritas Shoulder-Vice ScrewVeritas Shoulder-Vice Screw
Veritas Shoulder-Vice Screw
This vice screw is for the L-shaped shoulder vise used on Scandinavian-style benches. 1-1/8" dia. screw with single-lead Acme threads. The threaded guide is mortised into the vise shoulder, while the end guide attaches to the vise jaw. 7-1/4" clamping capacity (less wooden shoulder thickness), 13" overall. Mounting screws included. Made in Canada. Patented.
£42.55 inc VAT
Veritas Tail Vice Screw
Veritas Tail Vice Screw
The tail vice screw is essentially the same construction as a shoulder vice screw but without an end guide, this tail vice screw has a clamping capacity of 17" less thickness of wooden jaws (not included) and is 21" overall. 1.1/8" diameter screw with single-lead Acme threads. Mounting screws included. Wooden Handle not included, but can be purchased as an optional extra. Made...
£51.00 inc VAT

Veritas Tail ViceVeritas Tail Vice
Veritas Tail Vice
This vise can be used for both types of tail vise - with or without a shoulder. It has guide plates 2" wide by 15" long. The maximum opening is 8" (less the thickness of your wooden jaws). The single-lead Acme screw is 7/8" in diameter. Made in Canada. Patented.
£87.95 inc VAT
Veritas Special Bench Bolts
Veritas Special Bench Bolts
Most European benches use a bolt system to fasten leg sets to stretchers. The main advantage is that you can snug the bolts if anything loosens due to changes in humidity. The solid brass nuts on our bench bolts slide into a pre-drilled hole in the stretcher, and distribute pressure to prevent breakout. A bench can be made very rigid (without complex joinery) by using a wide stretcher, since the...
£39.50 inc VAT

Veritas Twin-Screw Vice
Veritas Twin-Screw Vice
The Veritas Twin Screw Vice is the only non-racking full-width end vise on the market. You can clamp anything anywhere in the vise and the jaws stay parallel. The chain drive ensures parallelism and eliminates the racking common in other vises. It can be operated using either handle. Even better, a spring-loaded lock pin lets you disengage the chain for controlled jaw skewing needed to equalize...
from £340.00 inc VAT
Veritas Wood Carver's ViceVeritas Wood Carver's Vice
Veritas Wood Carver's Vice
A good carver's vice should be adjustable in all three axis. This one has full rotation in two axes and 3" of height adjustment in the third axis. But more important, it has controlled release; when you relieve the clamping pressure, a combination of internal springs and O-rings provides residual resistance so that your work does not suddenly fall or rotate. You can reposition the work and...
£155.00 inc VAT

Accessories for the Veritas Wood Carver's ViceAccessories for the Veritas Wood Carver's Vice
Accessories for the Veritas Wood Carver's Vice
Accessories for the Veritas Wood Carver's Vice: Dog Hole Mount Assembly: The vice can be side or top mounted through any standard 3/4" dia. dog hole using the auxiliary rod/sleeve/wing-nut assembly, usable on benches from 5/8" to 4" thick. 3 1/2" Mounting Plate: 3-1/2" dia. by 1/2" thick mounting plate with a steel rod. 2" Mounting Plate: For mounting smaller pieces, such as duck heads or bird...
from £15.00 inc VAT
Veritas Carvers ScrewVeritas Carvers Screw
Veritas Carvers Screw
Turned from a solid bar of brass, this carver's screw, with its tapered tip and high-profile threads, grips securely and guarantees that remounted pieces are held as securely the third and fourth time as they were the first. The hex portion clamps securely in a vice while you thread on a blank, or you can use a spanner. The moulded tightening knob has a low-friction brass insert. At 5" long overall,...
£23.00 inc VAT