Lie-Nielsen Fishtail Chisel 1/2''
Lie-Nielsen Fishtail Chisel 1/2''
Fishtail Chisels are perfect for reaching the back corners of half-blind dovetails and paring other hard-to-reach areas. Their unique shape offers versatility for right and left hand recesses. Made from A2 Tool Steel, hardened to RC 60-62. Maine-harvested Hornbeam handles. Overall length is approximately 8". The bevel comes ground sharp at 25º, but a higher secondary bevel is advisable,...
£100.00 inc VAT
Robert Sorby Heavy Duty Corner Chisel
Robert Sorby Heavy Duty Corner Chisel
A heavyweight 1" (25mm) wide bruzz (corner chisel) for cleaning up deep corners of mortises. Ash Handle Overall Size:- 380-407mm Blade Length 239mm
£142.80 inc VAT

Robert Sorby Corner Chisel
Robert Sorby Corner Chisel
Designed for squaring up the ends of mortises, grooves or housings. The faces are precision ground to produce clean, accurate 90 degree angles. Often used nowadays to clean up after a router. Sharpen each face individually with an oil stone. The origins of this tool are from wheelwrights and millwrights who used a v shaped chisel to hollow out mortises in wheels and wooden beams (often referred...
£73.17 inc VAT
Ashley Iles Corner ChiselsAshley Iles Corner Chisels
Ashley Iles Corner Chisels
Ashley Iles corner chisels are available in 3/8" (9mm) and 1/2" (12mm).
from £36.00 inc VAT

Lie-Nielsen Corner Chisel 3/8''
Lie-Nielsen Corner Chisel 3/8''
Producing square mortises is exacting work. The Corner Chisel, used after the mortise has been roughed out by hand or with a slot mortiser—which produces round edged mortises—helps square corners easily and precisely. Made from A2 Tool Steel, hardened to RC 60-62 and ground razor sharp. Beveled at 30º. Comes with Maine-harvested Hornbeam handles. Overall length is approximately...
£150.00 inc VAT
Barr 7/8' Corner Chisel
Barr 7/8' Corner Chisel
Corner chisels are forged from tough carbon steel; these chisels are hand-tapered, bent to 90 degrees, then flat ground. Terrific for cleaning out mortises. 7/8" (22.225mm) x 7/8" (22.225mm) x 18" (450mm)
£216.00 inc VAT

Henry Taylor Swan Neck ChiselsHenry Taylor Swan Neck Chisels
Henry Taylor Swan Neck Chisels
A Henry Taylor swan neck chisel is used to clean the bottom of mortices. The chisel is levered in use, not struck. Available in 1/4", 5/16" and 3/8".
from £22.80 inc VAT
Kamanomi Japanese Chisel
Kamanomi Japanese Chisel
Used for cleaning the corners of joints.
£93.00 inc VAT

Morinomi Japanese Chisel
Morinomi Japanese Chisel
Used for cleaning the bottom of mortices.
£98.00 inc VAT
Sokosarai Japanese Chisel
Sokosarai Japanese Chisel
Used for scraping and levelling the bottom of mortices.
£93.00 inc VAT

Veritas Set of 3 Miniature ChiselsVeritas Set of 3 Miniature Chisels
Veritas Set of 3 Miniature Chisels
This chisel set is the latest addition to the Veritas line of fully functional miniature tools. Made at about 1/3 the scale of our regular bench chisels, each is only about 3-1/4" long overall and weighs less than a third of an ounce. At this scale, the three tools in the set have 3/8", 1/4" and 1/8" wide blades. All permit a delicate touch where fine, controlled cuts are needed. Their...
£43.60 inc VAT