Classic Hand Tools

View Cart
 
 
 
     
   
     

    Secure Online Shopping

   
 

Secure Online Shopping


Online Catalogue >  Clamps, Workbenches & Hardware  >  Veritas Quick-Release Vices


Veritas Quick-Release Vices


Veritas Quick-Release Sliding Tail Vise



Installing a tail vise is notoriously difficult, usually requiring a section of workbench to be cut away and rebuilt around a complicated vise mechanism. Not so with this one. It can be quickly incorporated into a new bench construction or easily retrofitted to an existing bench without major surgery.

The end plates are symmetrical, so you can install the T-handle and quick-release lever in a right- or left-handed orientation, allowing the vise to be mounted at either end of the bench.

Installation is straightforward: using the included hardware, attach the mounting plate to the underside of the bench, then register and secure the vise mechanism to the plate. Using wood that you supply, add a custom-made jaw the same thickness as the bench skirt.

The quick-release mechanism has a simple on-off lever that engages or disengages the Acme-threaded screw, which can apply force (up to 300 lb) in both clamping as well as spreading applications - something not possible with any other quick-release tail vise.

Maximum travel is 7". The body is ductile iron with zinc-alloy end plates, steel shafts and guide rods, and a maple handle. Requires an unobstructed mounting area at least 17" x 6" on the underside of the bench top.



Made in Canada. Patented.

Veritas Quick-Release Sliding Tail Vise Ref: 05G3001

Price includes VAT



Price: 325.00 (Including VAT at 20%)
Quantity:



Veritas Quick Release Front Vice



Using the same quick-release mechanism as our tail vise, our front vise has a simple on-off cam lever to engage or disengage the Acme-threaded screw, allowing it to apply up to 400 lb of force in either clamping or spreading applications.

The screw mechanism provides 12" of overall travel (less the thickness of your wooden jaw and bench apron). Tight body tolerances result in minimal jaw sag, even at full extension. An extruded aluminum screw cover keeps debris out of the screw mechanism and prevents the workpiece from contacting the lubricated screw.

Straightforward to install in new construction or as a retrofit to an existing bench, the vise requires an unobstructed mounting area on the underside of the bench top at least 12" wide by 16" deep (with a 2" thick bench apron and a 1" thick jaw).

The body is ductile iron with zinc-alloy endplates, steel shafts and guide rods, and a maple handle. Mounting instructions and hardware included.



Made in Canada. Patented.

Veritas Quick-Release Front Vice Ref: 05G3401

Price includes VAT



Price: 325.00 (Including VAT at 20%)
Quantity:


Veritas Special Bench Bolts

Most European benches use a bolt system to fasten leg sets to stretchers. The main advantage is that you can snug the bolts if anything loosens due to changes in humidity.

The solid brass nuts on our bench bolts slide into a pre-drilled hole in the stretcher, and distribute pressure to prevent breakout. A bench can be made very rigid (without complex joinery) by using a wide stretcher, since the stretcher is bolted into position.

The steel bolts are 6" long and 1/2" in diameter. The nuts are 25mm x 25mm and will fit perfectly in a 1" hole.

Made in Canada. Patented.

Veritas Special Bench Bolts Ref: 05G0702

Price includes VAT



Price: 29.50 (Including VAT at 20%)
Quantity:


 

Online Catalogue >  Clamps, Workbenches & Hardware  >  Veritas Quick-Release Vices

 
Home - Terms & Conditions - Site Map - Shipping - About Us - Contact Us - Visit Us - Privacy Statement

© Classic Hand Tools Ltd | Company Registration No. 04764498 | VAT No. GB 818 111 455