Crucible GoDrillaCrucible GoDrilla
Crucible GoDrilla
The Crucible GoDrilla extends the reach of your drill bits (and other tooling) without introducing any run out or wobble. This precision-machined tool (made in Tennessee) allows you to perform many unusual boring and fastening operations with immense ease and accuracy. DIY store bit extenders are cheap, poorly made and are designed for operations where run out is OK. An oversized hole will be hidden...
£72.00 inc VAT
Crucible Pinch RodsCrucible Pinch Rods
Crucible Pinch Rods
Please Note: Wood is not included. While there are many ways to determine if an assembled carcase is square, the easiest method is to use “pinch rods” to compare the corner-to-corner measurements. Unlike using measurements to compare the diagonals, pinch rods do not depend on reading and remembering dimensions. So they are much less prone to error. Also, pinch rods allow you to bring...
£66.00 inc VAT

Gransfors Bruk Splitting Wedge 460Gransfors Bruk Splitting Wedge 460
Back In Stock
Gransfors Bruk Splitting Wedge 460
Forged steel wedge. Twisted for maximum splitting. The poll has ground edges. The wedge has a 1¾" face, weighs 4 lb. Danger: Always wear adequate clothing and protection for your face and eyes. Book and protective leather sheath included.
£72.50 inc VAT
Veritas Large Tapered Reamer
Veritas Large Tapered Reamer
The Veritas large tapered reamer 5mm to 30mm (3/16" to 1-3/16") is useful to rustic furniture makers for back-tapering holes for through-tenon wedging. The bit is 140mm overall length with an 8mm hex shank. Designed for use in an electric drill, this tool may also be used in a traditional brace. The Veritas small tapered reamer 5mm to 19mm (3/16" to 3/4") is useful to rustic furniture makers for...
£30.95 inc VAT

Veritas Small Tapered ReamerVeritas Small Tapered Reamer
Veritas Small Tapered Reamer
The Veritas small tapered reamer 5mm to 19mm (3/16" to 3/4") is useful to rustic furniture makers for back-tapering holes for through-tenon wedging. The bit is 85mm overall length with an 8mm hex shank. Designed for use in an electric drill, these tools may also be used in a traditional brace.
£19.25 inc VAT
Veritas Tapered Reamer ProVeritas Tapered Reamer Pro
Back In Stock
Veritas Tapered Reamer Pro
The Veritas Tapered Reamer Pro is designed for use in a hand brace, our pro reamer offers excellent control and good cutting capability for general woodworking. It is particularly useful for tapering through holes where you want to be able to wedge tenons, such as in chair construction. This reamer has a cast steel alloy body, a separate spring-steel blade, and a pair of blade-adjusting set screws. When...
£59.50 inc VAT

Barr Gutter AdzeBarr Gutter Adze
Barr Gutter Adze
The Barr Gutter Adze is primarily used for roughing-out chair seats. It is also very useful for log scribe work, large bowl projects and totem work. It has a 30" hardwood handle which can be cut to desired length. 2 1/4" cutting edge, approx #6 sweep, overall head length is 9", head wt. approx 3lbs, handle length 30''
£215.00 inc VAT
Barr Hand AdzeBarr Hand Adze
Barr Hand Adze
The Barr Hand Adze is the best choice for roughing out your bowls and chair seats. Designed for maximum control the 2¼" cutting edge is just enough for the task at hand. Not too light, not too heavy it is the perfect addition to your workshop! 2¼" cutting edge, head length 8", total weight 2lbs, handle length 15"
£190.00 inc VAT

Henry Taylor Bowl AdzeHenry Taylor Bowl Adze
Henry Taylor Bowl Adze
Sheffield made hand forged adzes by Henry Taylor for single handed use. This one is a tight gouge (sweep 9), however this lucky fella is outcannel which makes it a Bowl Adze. At the other end to the cutting edge is a square faced hammer poll. All Henry Taylor adzes have an ash handle of 250mm (about 10") . The overall head size (from the square face of the hammer poll to the cutting edge)...

5

£99.50 inc VAT
Henry Taylor Hand Adze Deep Curved BladeHenry Taylor Hand Adze Deep Curved Blade
Henry Taylor Hand Adze Deep Curved Blade
Sheffield made hand forged adzes by Henry Taylor for single handed use. There is a choice of 3 adzes; this one is a tight incannel gouge (sweep 9), and is offered with an incannel or outcannel grind. The outcannel grind is favoured by those working concave surfaces as it allows the leading edge to enter the working area easier. At the other end to the cutting edge is a square faced hammer...
£99.50 inc VAT

Henry Taylor Hand Adze Shallow Curved BladeHenry Taylor Hand Adze Shallow Curved Blade
Henry Taylor Hand Adze Shallow Curved Blade
Sheffield made hand forged adzes by Henry Taylor for single handed use. There is a choice of 3 adzes, this one a gouge end with a shallow/mid gouge or there is a tight gouge (sweep 9) and a 50mm (2") straight edge (like a chisel). At the other end to the cutting edge is a square faced hammer poll. All the adzes have an ash handle of 250mm (about 10") . The overall head size (from the...
£99.50 inc VAT
Henry Taylor Hand Adze Straight BladeHenry Taylor Hand Adze Straight Blade
Henry Taylor Hand Adze Straight Blade
Sheffield made hand forged adzes by Henry Taylor for single handed use. There is a choice of 3 adzes, this one a 50mm (2") straight edge (like a chisel) or curved end (like a gouge) with either a shallow/mid gouge or a tight gouge (sweep 9). At the other end to the cutting edge is a square faced hammer poll. All the adzes have an ash handle of 250mm (about 10") . The overall head size...
£78.00 inc VAT

Leonhard Muller Round AdzeLeonhard Muller Round Adze
Leonhard Muller Round Adze
These adzes are from Leonhard Muller's Carpenter's Hatchets range. There are 3 sweep widths to chose from and all come with straight ash handles. Straight 400mm - 450mm ash handles (about 16" - 18") Choice of 40mm, 50mm or 70mm wide medium sweep cutting edge.
£95.00 inc VAT
Muller French-Style Sculptors AdzeMuller French-Style Sculptors Adze
Muller French-Style Sculptors Adze
Again, these adzes are from Leonhard Muller's Carpenter's Hatchets range but they are based on the traditional French design where the head gradually flares from the poll. 3 sweep widths to chose from and all come with straight hickory handles. Straight 450mm hickory handles (about 18") Choice of 65mm, 60mm or 56mm wide medium sweep cutting edge.
£105.00 inc VAT

Pfeil Curved AdzePfeil Curved Adze
Pfeil Curved Adze
The Pfeil Curved Adze, forged from quality steel, is available in Standard and Small: Standard: Length 460mm (18”), cutting edge 95mm (3¾"), weight 1100g. Small: Length 280mm (11”), cutting edge 50mm (2”), weight 600g. Please be aware that these do not come pre-sharpened.
£113.50 inc VAT
Pfeil Straight AdzePfeil Straight Adze
Pfeil Straight Adze
The Pfeil Straight Adze is forged from quality steel and comes in two sizes: Standard: length 460mm (18”), cutting edge 80mm (3”), weight 1kg Small: length 280mm (11”), cutting edge 50mm (2”), weight 500g Please be aware that these do not come pre-sharpened.
from £101.00 inc VAT

Ray Iles 8' Mike Abbott Pattern Draw KnifeRay Iles 8' Mike Abbott Pattern Draw Knife
Ray Iles 8' Mike Abbott Pattern Draw Knife
This drawknife designed by Mike Abbott and manufactured by Ray Iles has a 8" cutting edge, with beech handles. This 8" drawing knife has slightly flared handles which are bent backwards, meaning the handles are at approximately the same angle, whether you are using them back down, or cannel down. Made in England
£67.50 inc VAT
Ray Iles 6' Small Draw KnifeRay Iles 6' Small Draw Knife
Ray Iles 6' Small Draw Knife
The Ray Iles 6" drawknife is a standard carpenter's drawknife, made from 01 high carbon steel and fitted with beech handles and brass ferrules. Made in England
£55.00 inc VAT

Ray Iles 6' Gent's DrawknifeRay Iles 6' Gent's Drawknife
Ray Iles 6' Gent's Drawknife
This Gent's drawknife made by Ray Iles is a delicate drawknife which has a 6" cutting edge and slightly splayed handles. It is made from O1 high carbon tool steel and is fitted with beautiful curved boxwood handles and brass ferrules. Made in England
£80.00 inc VAT
Pfeil Large Straight Drawknife
Back In Stock
Pfeil Large Straight Drawknife
This Pfeil Straight Drawshave comes with a goatskin case and has cherry handles. The blade is 250mm in length and the overall length is 440mm. Classic carpenters design with straight back and straight blade.
£141.00 inc VAT

Pfeil Large Curved Drawknife
Pfeil Large Curved Drawknife
Pfeil large curved drawknife with Cherry handles, and goatskin protector for blade. 430mm overall length, blade length 240mm, weight 450g. Gently curved blade.
£84.50 inc VAT
Pfeil Small Drawknife
Pfeil Small Drawknife
This is a compact, handy draw knife from Pfeil with a razor-sharp cutting edge. Very useful for small scale work. Made with cherry handles, the length of the blade is 110mm and the overall length is 290mm.
£47.00 inc VAT

Flexcut 3' Draw Knife KN25
Flexcut 3' Draw Knife KN25
This handy little draw knife by Flexcut was developed for fan carving but works great for skinning small areas of bark and roughing-off corners. Made in the USA by Flexcut.
£57.90 inc VAT
Flexcut 5' Flexible Draw Knife KN16
Flexcut 5' Flexible Draw Knife KN16
This flexible Flexcut draw knife has 5 inches of workable edge, designed to flex around contours where large amounts of stock need to be removed quickly. The tool can be flexed to accommodate concave or convex surfaces. Cuts can be made that conform more closely to the finished shape, taking less time to sand or scrape. The curved edge gives a skew-like cutting action for a low resistance cut. This...
£63.40 inc VAT

Veritas Carvers Drawknife - PM-V11Veritas Carvers Drawknife - PM-V11
Veritas Carvers Drawknife - PM-V11
An ordinary drawknife is too large for most carving - the Veritas drawknife is designed for ease of use with maximum control. The teardrop-shaped handles are cocked at 45° to the blade and nestle comfortably in your hands. The polished 4" x 1/8" x 3/4" blade is ground and honed to a perfect edge, and is supplied with a blade guard. The drawknife blade is custom made for us...
£107.00 inc VAT
Pfeil Small Straight Drawknife
Pfeil Small Straight Drawknife
Pfeil Small straight drawknife with cherry handles. Overall length 310mm with a cutting edge of 120mm.
£40.00 inc VAT

Robert Sorby DrawknifeRobert Sorby Drawknife
Robert Sorby Drawknife
10" cutting edge, ash handled draw knife. Straight back and straight blade with slightly splayed handles.
£95.00 inc VAT
Flexcut 1'' Mini Draw Knife KN17
Flexcut 1'' Mini Draw Knife KN17
This miniature draw knife by Flexcut is designed for hard-to-reach areas, where a pulling action is more conducive to efficient stock removal. The flexible shank allows the cutting angle to be changed easily for contoured cuts. Made in the USA by Flexcut.
£33.40 inc VAT

Benchcrafted DrawsharpBenchcrafted Drawsharp
Benchcrafted Drawsharp
Ease and safety With the Benchcrafted Drawsharp, the cutting edge is facing away from your body and fingers, the honing action is parallel to the blade, and your fingers are safely behind the cutting edge at all times. If you've shied away from using drawknives because of sharpening, the Drawsharp will open the door to this wonderful tool, whether you’re a chairmaker, or looking to add the drawknife...
£112.00 inc VAT
Accessories for the Benchcrafted Drawsharp
Accessories for the Benchcrafted Drawsharp
Rehab kit Most knives will be in good enough condition to use the abrasives included with the Drawsharp. But for those which require more aggressive material removal (removing knicks or severely blunted edges) or for those who may not want to grind their knife, Benchcrafted offer a rehab kit with medium and coarse diamond abrasives. The kit includes two sleeves and two each of coarse and medium diamond...
from £4.58 inc VAT

Boggs Concave SpokeshaveBoggs Concave Spokeshave
Boggs Concave Spokeshave
The Boggs Concave Spokeshave is a collaboration between Kentucky Master Chair Maker Brian Boggs and Lie-Nielsen Toolworks. A 2-5/8" diameter sole makes this tool the right choice for working chair spindles and other round parts. Weight 8 oz. Body is 9-5/8" long, A-2 blade 1-1/8" x 1/8" thick, Bronze body and cap. Hickory handles.
£249.00 inc VAT
Clifton 500 10" Convex SpokeshaveClifton 500 10" Convex Spokeshave
Clifton 500 10" Convex Spokeshave
Clifton Spokeshaves are made from virtually unbreakable spheridal graphite/malleable iron; the surfaces are finished and polished to give maximum comfort in the hand; the weight and balance permits the Spokeshave to sit firmly on the wood so that only a stroking action is required to make them cut. The firm seating and fine adjustment allow the woodworker to make delicate nuances in the weight of cut....
£125.00 inc VAT

Clifton 550 10" Concave SpokeshaveClifton 550 10" Concave Spokeshave
Clifton 550 10" Concave Spokeshave
Clifton Spokeshaves are made from virtually unbreakable spheridal graphite/malleable iron; the surfaces are finished and polished to give maximum comfort in the hand; the weight and balance permits the Spokeshave to sit firmly on the wood so that only a stroking action is required to make them cut. The firm seating and fine adjustment allow the woodworker to make delicate nuances in the weight of cut....
£125.00 inc VAT
Clifton 600 Flat 10" SpokeshaveClifton 600 Flat 10" Spokeshave
Clifton 600 Flat 10" Spokeshave
Clifton Spokeshaves are made from virtually unbreakable spheridal graphite/malleable iron; the surfaces are finished and polished to give maximum comfort in the hand; the weight and balance permits the Spokeshave to sit firmly on the wood so that only a stroking action is required to make them cut. The firm seating and fine adjustment allow you the woodworker to make delicate nuances in the weight...
£125.00 inc VAT

Clifton 650 Curved 10" SpokeshaveClifton 650 Curved 10" Spokeshave
Clifton 650 Curved 10" Spokeshave
Clifton Spokeshaves are made from virtually unbreakable spheridal graphite/malleable iron; the surfaces are finished and polished to give maximum comfort in the hand; the weight and balance permits the Spokeshave to sit firmly on the wood so that only a stroking action is required to make them cut. The firm seating and fine adjustment allow you the woodworker to make delicate nuances in the weight...
£125.00 inc VAT
Lee Valley Cast Round Spokeshave
Lee Valley Cast Round Spokeshave
Founded in 1825, Edward Preston & Sons, Ltd. produced some of the finest tools of the Victorian age. Lee Valley have created a close replica of their model 1374 round-bottomed spokeshave, a tool as elegant as it is effective. Smaller than typical spokeshaves at 6¾" long overall, it is designed for fine smoothing and shaping, with a tight mouth opening that helps reduce tear-out,...
£77.50 inc VAT

Lie-Nielsen Boggs SpokeshaveLie-Nielsen Boggs Spokeshave
Lie-Nielsen Boggs Spokeshave
The original Boggs Spokeshave is hefty and solid, weighing 12 oz. Designed for fine, precise shaping in all woods. Available with either a flat or curved sole. Body is 10" long with a 1" wide flat sole. The sole of the Curved Spokeshave has a gentle, 5" radius for working inside curves. 2" wide x 1/8" thick A2 blade. Bronze body and cap. Hickory handles. Weight is 12 oz.
from £173.00 inc VAT
Lie-Nielsen Small Spokeshave
Lie-Nielsen Small Spokeshave
This Lie Nielsen spokeshave is based on a lovely tool that hasn’t been available since Edward Preston and Sons went out of business in the 1930’s. Lightweight but solid. Redesigned for fine, precise shaping work in all woods. Available with a flat or curved sole (1-1/2" radius). 6-3/4" long, with a 5/8" wide sole Bronze body and cap with with an A-2 cyro blade...
from £167.00 inc VAT

Veritas Concave Spokeshave PM-V11
Veritas Concave Spokeshave PM-V11
The Veritas Concave spokeshaves have a extremely durable PM-V11 steel alloy blade, seated at 45° to the sole. The thick blade, carefully machined lever cap and blade bed all combine to produce chatterfree cutting in virtually all conditions. This spokeshave is popular with chair and paddle makers, being the first choice for a wide range of jobs from small spindles to large oars. The ductile...
£118.00 inc VAT
Veritas Flat Spokeshave PM-V11Veritas Flat Spokeshave PM-V11
Veritas Flat Spokeshave PM-V11
The Veritas flat spokeshave has a 1/8" (0.125") thick PM-V11 tool steel blade, seated at 45° to the sole. The thick blade, carefully machined lever cap and blade bed all combine to produce chatterfree cutting in most situations. The ductile cast iron body is fitted with African rosewood handles that are shaped for comfort and control, offering several ways to grip the tool comfortably...
£115.00 inc VAT

Veritas Low Angle Spokeshave
Veritas Low Angle Spokeshave
The Veritas Spokeshave uses a basic traditional shape, not of the spokeshaves of the last century, but of the century before. Until about 1900, the vast majority of spokeshaves were low-angle spokeshaves with wooden bodies. The blades were hand forged with upturned tangs that fitted into holes pierced in the body of the shave. Wedged in position, they were adjusted by tapping the ends of the...
£95.95 inc VAT
Veritas Round Spokeshave PM-V11
Veritas Round Spokeshave PM-V11
The Veritas Round Spokeshave has a 3.2mm thick PM-V11 steel blade, which fits perfectly onto the machined blade. The ductile cast iron body is fitted with hardwood handles, shaped for comfort and control. The toe serves as a thumb rest allowing the user to choke up on the body to attain exceptional control. Twin adjustment wheels quickly and accurately control cut depth and skew and shims let...
£120.00 inc VAT

Veritas Scraper Shave
Veritas Scraper Shave
The Veritas Scraper Shave is a versatile small scraper suitable for small-scale work, fine detailing, or any application where a normal scraping plane would be too large. The design of the tool allows a controlled scraping action that effectively smoothes the workpiece. Can be used as a companion tool with the chair devils for smoothing of non-round chair parts such as crest rails, arm bows and...
£106.00 inc VAT
Ray Iles Rounding PlanesRay Iles Rounding Planes
Ray Iles Rounding Planes
A rounder is also known as rotary plane and is used to create accurate tenons or for rounding spindles for chairs. All of these 6 rounders are made by Ray Iles. The thick blade is held in place by two washered screws which allows you to adjust or remove the blade for sharpening very easily. Beech body, lightly linseed oiled. Having reduced your spindle to a little over the size of the rounder...
£49.50 inc VAT

Veritas Tapered Tenon CuttersVeritas Tapered Tenon Cutters
Veritas Tapered Tenon Cutters
Veritas tapered tenon cutters will put tapered tenons on the tips of turnings, dowels or rustic furniture components to fit into tapered holes; for example, legs and spindles on a Windsor chair. Use the cutter like a hand-held pencil sharpener; you either rotate the workpiece while pressing it into the cutter body or you can rotate the tool on the workpiece. Works equally well in soft, green or hard...
£56.00 inc VAT
Veritas Dowel & Tenon CuttersVeritas Dowel & Tenon Cutters
Veritas Dowel & Tenon Cutters
Obtaining dowels to perfectly match a project or specific species of timber, is to say the least, almost impossible. Not so if you own a Veritas Dowel cutter and have a few timber off-cuts to hand. These cutters can be used two ways. Either use them like a hand-held pencil sharpener, to put accurate tenons on the tips of turnings or on rustic furniture components. Alternatively using a cordless drill,...
from £48.00 inc VAT

Accesories for Veritas Dowel & Tenon Cutters
Accesories for Veritas Dowel & Tenon Cutters
Use the 1/2" drive socket for the 3/8" & 7/16" sizes. The 5/8" drive socket for the 1/2" dowel. The four-sided square sockets have a 3/8" square-drive end. The socket adaptor has a 1/4" hex shank. Dowel Cutters made in Canada. Patented.
from £3.45 inc VAT
Curved Replacement Blade for Veritas Dowel & Tenon Cutters
Curved Replacement Blade for Veritas Dowel & Tenon Cutters
The curved blade is a replacement blade for the Veritas Dowel and Tenon Cutters. It can also be used on the 3/8", 7/16" and 1/2" Veritas Tapered Tenon Cutters (not recommended for the larger sizes as overheating may occur).
£22.95 inc VAT
Page: 1 | 2 | 3 |